Q1) Concrete mix Design for M35 Ans: Target mean strength for M35 grade concrete Fck=fck+1.65s Fck=35+1.65*5 Fck=43.25 N/mm2     2.Determination of water cement ratio As per IS 456 Table no.5 Water cement ratio = 0.45        3.Selection of water content Water cement ratio for 100mm slump=…

   Dimension of First floor plan Bedroom:4 X  3.5 Toilet : 3.5 X 2.5 Study room : 3 X 3.3 Terrace : 13.69 X 4 Bed room : 4.5 X 4     Dimenaion of ground floor plan Bed room : 4.5 X 4 Dining : 4.5 X 3.5 Parking: 6.23 X 3.5 Pooja room : 2.8 X 3.5 Store room : 3.5 X 2.8 Wash room : 2.5 X 3.5 Guest…

    AIM: To create diffrent geometrics shape given above by coordinate system using line and circle tool   INTRODUCTION: COORDINATE SYSTEM:It is a method which allow to define the placement of points to determine the position of point/geometricsshape.This system is mainly of two types thy are ABSOLUTE COORDINATE…

   AIM:To draw cross section of wall over footing     Commands used: Line Rectangle  Trim   Procedure  Step 1:Create Rectangle by using REC in command box Specify the first corner point as (5,5) Specify the length of rectangle=0.9 units in command box Specify width of rectangle =…

  AIM:Drafting of various geometrics using chamfer , fillet tool in autocad   Drawing No: 1       Drawing No:2       Drawing No:3         Drawing no 4                                …

Aim:To draw the layout of the residential plan Commands used: XL-H Offset fillet Extend Trim PROCDURES: First create a new Autocad file with imperial settings Type ''Engineering'' in units and selects inches Set the limits with command ''LIMITS'' specify the left corner points and right corner enter zoom all draw construction…

AIM:To create a column schedule as shown in the figure.     PROCEDURE: STEP1 In the command tab type "L'' to create tables In the command type ST(Text style)>Aerial.shx>left In the command type text to text the given text in drawing In the command type mtext>symbols>to get diameter symbol RESULT:…

AIM:TO Draw the elevation and details of a wardrobe as shown in figure below.After sketching and to provide the dimensions and text with use of layers   PROCEDURE: STEP 1: Units are set to be in "Engineering" and in ''mm'' Limits and Limitmax are also set Click zoom and enter ''all''     2.STEP 2: In the…

AIM: To create plan, section , elevation as shown in figure by using proper dimension and technique and dimension style to document the project and also assuming  the sizes of doors and windows  as per                   construction INTRODUCTION The  plan…

AIM: To design and design and layout of a residential building having plot size 60'X 20' facing east direction   ARCHITECTURAL DRAWING   Site plan layout Ground floor plan First floor plan  Elevation Section view   STRUCTURAL DRAWING Column layout Beam layout Footing layot     PROCEdDURE…

AIM: To create the template as shown in the figure   PROCEDURE:      Creation of Custom1_Titleblock In the command type ''UN'' and select the units and scale Type offset distance in the command box  Select the object the to offset  Select the text tool from the ribbon tab and enter…

To create the multiple viewport scaling and drawing and setting in template in the drawing   PROCEDURE   AIM: To create a layout of plan and section of project using template m-arch.dwt   Open plan and section of a challenge number 7 Select layout at the bottom Right click on template and open ''march template…

AIM: To create kitchen layout and hatching of architectural elements and sectional view of industrial building   PROCEDURE Units are set to be  mm  limmax and limits are set zoom command is also set  STEP 1) In the command type ''rec'' and create rectangle of 4734 X  3688 In the command type offset…

AIM: To create the a 3d furniture as shown  in the figure   PROCEDURE: Type  ''un'' and set the  units in ''engineering'' and ''inches''  Select the workspace in '3d modelling'' in the workspace Take line command select the first point  specify the next point >@0,0,2.6''>enter  specify…

AIM: TO CREATE THE ISOMTRIC VIEW OF THE BUILDING   PROCEDURE: Draw the floor plan and elevation of the building and given imfor,mation Create the layer 3d wall, 3d window Select the wall in floor by using command boundry creathe region inside the boundry Then use the subtract command to subtract the inner region…

AIM: To create the 3d dimension of the buiding   PROCEDURE: External wall : 9 inch window: 3' X 4 All dimnsion are in inches    Click on the  autocad and opne application  Set the unit in ''engineering'' and inches Keep ortho mode on Keep decimal degrees zero Assign color to each to building  use…

AIM: To create the project and name project appropriaeky   PROCEDURE:  Initially open the  revit software               choose architectural template then click on project and then click on ok Now,open revit software opens Click on the save icon which is on the left…

AIM: To know what is BIM and to summerize the features of BIM and benifits of using BIM over 2D cad tools             BIM Bim is an acronym for building information building or building information management.It is a highly collabarative process that allows architects,engineers,…

AIM: To create the floor for layout created in the week 2 and provode appropriate material and thickness to the floor   PROCEDURE: Initially open the week assignement        Now, in order to create the floor ,go to architectural tab of the ribbon and choose the floor option Now choose pick boundry…

AIM: To create the ceiling above the wall at first floor level     PROCEDURE: Initially open the week 3 assignement from the revit software We open the revit software and select the ceiling option from the architecture toolbar       After selecting the ceiling option select the room …

             INTRODUCRION TO NATINAL BUILDIONG CODE AND STEPS IN A CONSTRUCTION PROJECT          1.WHY ARE BUILDING CODES OR STANDARD  ESSENTIAL FOR THE MODELING/ EFFICENCY OF DRAWING IN REVIT   The NATIONAL BUILDING CODES (NBC) is a document…

                                                                                         USAGE…

QUESTION :1 ANSWER: Office buillding   QUESTION:2 ANSWER My building is constructed in plan area or flat area Location: Ahmednagar, Maharahtra,India   QUESTION 3:   AIM: To draw the structural model of office building   PROCEDURE: Start the revit 2023 software        Then click…

                                                                                           …

PREPARING SCHEDULE AND COST ESTIMATE FOR A BUILDING USING REVIT INTRODUCTION SCHEDULE: A schedule is a tabular  display pof information,extracted from tghe properties of the elements in a project,A schedule can list every instance of the type of element you are scheduling ot it can collopse multiple instances…

  Creating Conceptual mass in revit and creation of sinusoidal curve and a parametric stadium using dynamo Introduction   Dynamo is an open source visual programming language for revit,written by designer and construction professional.Its a programming language that allows you to type lines of code,while creating…

                                                              Usage of Navigation tool,Timelinear and clash detection test using Naviswork    INTRODUCTION:…

What is mode of failure or damage of the beams in the figure above? are the damage repairable ?Elaborate      We can clearly see in this image damage is done in the bottom of the beam and column is clear The above Figure shows that flexural cracks devlop at the bottom part of the beam  Flexural failure…

1.Compute lateral stiffness of the one story frame with an intermediate realistic stiffnessof the beam.The system has e dof's as shown.Assume L=2h and Elb=Elc    SOLUTION      Stiffness matrix is determined by the method called stiffness matrix method of analysis   In this above image the…

Question 1                                                                                          …

QUESTION :1   Comment on the layput of the framing ,concerning earthquake resistance in the two horizontal direction X or Y (dots are column, lines  depicts beams).Look into aspects of symmetry.redundancy and bi directional stiffness and ductility                  …

QUESTION 1   The building shown 20 X 35m in plan has column on a 5 X 5 m grid and shear wall in three alternatives arrangements (a),(b),(c), all with the same total cross sectional area of the sear walls.Compare the threealternatives ,taking into accounting the restraint floor shrinkage ,the lateral stiffness and…

      AIM:  To modelling a 25 storey building on etabs 2020 with structural properties including ground floor or plinth level at a height off 1.5 meters from the base and a story  height of 3 meter         PROCEDURE: Open ETABS 2020 application Click the file menu and choose…

AIM: To provide details of longitudnal and shear reinforcement for the two continous beams usinf ETABS   PROCEDURE:       STEP 1): After downloading the model given in the question ,click the concreter frame design tool in the ribbon tab Choose the appropriate design combination Select the appropriate…

      AIM: To provide details of longitudnal reinforcement for the two column from foundation to terrace level.         STEP1:) Open a G+4 Etab file Click the concrete frame design info option Select the display design info option Choose design output as longitudnal reinforcement…

                                                                            ANALYSIS AND DESIGN USING RCC SHEAR WALLS IN THE…

AIM: To run a model response spectrum analysis and check analysis results of the ETABS model for the inter story drift requirements ,vertical and planner irregularities ,minimum shear wall requirements ,amximum axial load ratio for column  and shear walls ,an effective moment of inertial for beams   PROCEDURE: …

AIM: To design a square footing  for a clumn size for 400 X 400.   PROCEDDURE:   Design of square footing Net soil Upword Pressure Depth of footing Gross bearing capacity Reinforcement Check For one way shear Check for two way shear   Design Of square Footing   Column size : 400 X 400 mm Soil…

Model the isolated footinf provided in week 11 challenge on SAFE. Analyze and design it to verify the size,depth and steel provided as per calculations     PROCEDURE Open  the SAFE 2020 Software CLick on the new model CLick on the new model Display Units - Metric SI Dlect the Region -Indian Select the Concrete…

AIM: To carryout modelling analysis ,design and preparation of construction drawings a G+3 RCC building situated in Guwhahati ASSAM   PROCEDURE: Initially Open the Etabs sopftware and then provide the grid and story information                     We need to define…

       Project1 : Comparative study  of diffrent storey building for seismic forces         AIM: Comparative study of diffrent storey building for seismic forces        INTRODUCTION: Factors influencing the Natural Period if a building      …

. AIM: To summarize the user interface in TSD   PROCEDURE:  Open the tekla software and click on the new option  Now project workspace will be visible     Now demostrate the use of scene content  Open the tekla software and click on the new option Now project workspace will be visible Now click on the scene content  With…

AIM: To model column for industrial steel structure using TSD   PROCEDURE :  Initially opened the tekla file which we created in the last week Check the level by clicking the construction levels         To add pedestal properties click on the manage property in the home menu, the  manage…

 AIM : To create beam properties for first floor  and model the beams   PROCEDURE:  Open the tekla software  Open the Previous file     Go to home tab and manage properties set         Define beams B2 and go to model and select steel beam and draw beam as shown…

AIM : To calc502ulate dead load in design report based on IS code and apply the dead load on model   PROCEDURE :   Dead load = 1.2 Kn/M^2 Finishes    = 500 mm X 24 Kn/m^2 = 1.2 Kn/m^2 Brick wall load  = 0.15 X 20 X 5.2    = 15.6 Kn/m^2 Brick wall load  = 0.15 X 20 X 6.8   …

Generate module wind loading in the design report based IS code as per following input   Basic wind speed Terrain category 2   AIM : To calculate wind load as per IS CODE 875 part -III   INTRODUCTION : Wind load is calculated according to IS code 875 -III For industrial Building     …

AIM : To analyze the model and summarize the study of bending moment , shear force and deflection for the elements of the model satisfying all the loads and load combination as per the code     Open the previous model with all the loads assigned the model  Performing analysis check for the settings of the…

AIM : To analyze and design a steel building to 10T crane as per IS standard code using TEKLA STRUCTURAL DESIGNER   INTRODUCTION : First Order kinear analysis for most of the cases  The process performed when this analysis is run can be summarized as follows             …

 Aim : To set up a model for RC buillding design   PROCEDURE: Open Tekla Structural design GO to settings---> Structural defaults Select the SSL for the cover in contact with the ground Eneter the cover values as given in the above table         For the cover above the ground change default…

AIM: To calculate the dead load in design based on IS code and apply on the model   Tools used : Load cases ,Full UDL , Area load ,Property window\   Calculation :    Slab model   Finishes Loading = 0.05 X 24 KN/M^2 =1.2 KN/m^2  Brick Wall with cement plaster thickness = 225mm Unit weight = 20KN/m^2 Floor Height = 3.6…

AIM : To generate the seismic loading based on IS Code and zone II using seismic wizard   INTRODUCTION : Seismic load indicates how much seismic energy a structure would need to endure in a specific geographic location   PROCEDURE Load toolbar > Click on seismic load >Seismic Wizard      …

AIM : To design the RC column and beams after the analysis   PROCEDURE : OPen the tekla file Now right click the member to be designed and then select interactive design and static   Design of Column   Select Static  from interactive design after that dialogue box appears  This dialogue box shows…

AIM : To design slab and foundation of the model   INTRODUCTION :  First order analysis , Status ,Check panel ,Properties     PROCEDURE    Open file created in TSD and open 3D view         Click on First order analysis and perform  analysis and also perform analysing …

AIM : To generate report for steel industrial and RC structure using TSD   PROCEDURE : Open the saved tekla software Now go to report option from the ribbon and select model report NOw select the load cases and combination summary to obtain report Click on the show report to obtain the report      …

AIM : To devlop model as per given plan and analyze and design structure   TOOLS USED    Paint  Manage properrty set  Constructiokn levels  Grids  Column Beams Model report Show report  Interactive design Slab on beams Frames Roof panels Wall panels Loads Loadcases Seismioc wizard   PROCEDURE Open the plan in them in paint…

AIM : To devlop model as per given plan and analyze and design structure   TOOLS USED    Paint  Manage properrty set  Constructiokn levels  Grids  Column Beams Model report Show report  Interactive design Slab on beams Frames Roof panels Wall panels Loads Loadcases Seismioc…

AIM : Write the steps involved in stadd pro file through web mail   PROCEDURE :  Open the soaftware in the landing page Click on share icon  Click on send mail Browse the file you want to share Ensure that ypu are sign in Type of material used in staad pro       There are three methods…

 1.1 How will you design circulat section to column So in order to assign the circular section to column is discussed below CLick on option define THen there will be another dilogue box xalled property in that dialogue box select the option circular section from given list After that give desired diameter for that…