calculation of concrete mix design for M35 grade concrete with Fly ash: . Data collection  grade designation = M35  Type of cement = OPC 43 grade conforming to Is 8112  Max nominal size of aggregate = 20mm  max w/c ratio = 0.45  workability = 100mm  exposure condition = severe  method…

Important structural drawings are: centre line diagram Footing and cloumn layout wih reinforecement details column schdule with reinforcement details plinth beam layout with reinforcement details first floor beam layout with reinforcement details first floor slab layout with reinforcement details lift pit and head room…

  1. Absolute cooardinate system:  In the absolute coardinate system the following steps should be followed as a procedure. At first open the autocad and set dimensions that the dimensions are in mm. Then enter the Line command in autocad and after that enter the first point of the given diagram as (2,1) that…

Q1.  Aim: Draw the given column cross section using autocad. Procedure: The detail step by step procedure to draw the given cross section of column using autocad are: At first open the autocad and set dimensions that the dimensions. for drawing the column first use the rectangle command called rec enter and select…

Q1. Aim: To draw a given diagram using autocad procedure: The  following steps should be followed as a procedure to draw a given diagram using autocad To draw the given diagram in autocad, the following steps should be followed as a procedure. At first open the AutoCAD and set dimensions that the dimensions are in…

Challange: 1: Aim: To draw a given floor plan using autocad. procedure: The  following steps should be followed as a procedure to draw a given floor plan using autocad To draw the given floor plan in autocad, the following steps should be followed as a procedure. At first open the AutoCAD and set dimensions that the…

1.  Aim: To draw a given table schdule using autocad. procedure: The  following steps should be followed as a procedure to draw a given section table using autocad To draw the given section table in autocad, the following steps should be followed as a procedure. At first open the AutoCAD and set dimensions that…

1.  Aim: To draw a given cross section of wardrobe using autocad. procedure: The  following steps should be followed as a procedure to draw a given cross section of a wardrobe using autocad To draw the given cross section of a wardrobe in autocad, the following steps should be followed as a procedure. At first…

1. To draw a given floor plan using autocad. procedure: The  following steps should be followed as a procedure to draw a given floor plan using autocad To draw the given floor plan in autocad, the following steps should be followed as a procedure. At first open the AutoCAD and set dimensions that the dimensions are…

a. Floor plan of plot size (60'x20') To draw a given floor plan using autocad. procedure: The  following steps should be followed as a procedure to draw a given floor plan using autocad To draw the given floor plan in autocad, the following steps should be followed as a procedure. At first open the AutoCAD and set…

1. Aim: To draw a given table schdule using autocad. procedure: The  following steps should be followed as a procedure to draw a given section table using autocad To draw the given section table in autocad, the following steps should be followed as a procedure. At first open the AutoCAD and set dimensions that the…

1. Aim: To draw a given cross section of kitchen using autocad. procedure: The  following steps should be followed as a procedure to draw a given cross section of a kitchen using autocad To draw the given cross section of a kitchen in autocad, the following steps should be followed as a procedure. At first open the…

1. Aim:  Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. To draw a given floor plan using autocad. procedure: The  following steps should be followed as a procedure to draw a given floor plan using autocad…

1. Aim: To Create a 3D Furniture element as shown in the Figure in autocad. procedure: The  following steps should be followed as a procedure to draw a given 3d model table using autocad To draw the given 3d model table in autocad, the following steps should be followed as a procedure. At first open the AutoCAD and…

1. Aim: Create a 3D Isometric View of the building with plan and elevation given.  procedure: The  following steps should be followed as a procedure to draw a given 3D Isometric View of the building with plan and elevation using autocad To draw the given 3D Isometric View of the building with plan and elevation…

1. Aim: To create Create a 3 dimensional model of the residential building with a rendered view. procedure: The  following steps should be followed as a procedure to draw a given floor plan and  To create Create a 3 dimensional model of the residential building with a rendered view using autocad To…

1(a): Aim: To determine the failure as shown in the given figure. Procedure: In the given figure to determine the failure that the failure in the given figure is cloumn and beam junction falure. The stress that can be produced due to the During earthquakes, the failure of beam-column joints is governed by bond and…

1. Aim:  To determine the lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The system has 3 DOFs as shown. Procedure: This structure can be analyzed by any of the standard methods, including moment distribution. Here we use the definition of stiffness influence…

1) Given that A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived.

1) In the above diagram given to Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. Symmentry: It indicates that when the given structure is divided sectionally in the X axis and y axis the symmentical views is look like similarly same that is when the given structure is cut into x axis…

1) In the given sturctural diagram the shear walls arein the L shaped structure at the edge of the plan. so the sturcture with that given plan as the structure is more restrained it will be more shrinking, expanding and cracking. .  In the second diagram given that the shear walls are on the middle of the structure…

Aim: Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. Given that the Structural Element Sizes  Beams : 300 × 400 mm …

1) Given that the to calculate the in Etabs Factors influencing the dynamic characteristics of a building Factors influencing the Natural Period of a building Factors influencing the Mode shape of oscillations A) In this given that the building is a 2 storeys building with number of bays in X axis as 4 and Y axis as 3…

Aim:Detail design of beams in Etabs 2018.The ETABS file for a G+4 building is provided. Run the analysis and design of the RCC Moment ResistingFrame. The following challenge deals specifically with twocontinuous beams on the 1st floor.1 ) 3 span continuous beam along grid A2) 7 span continuous beam along grid 3Provide…

GIVEN: Given that The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment Resisting Frame. The following challenge deals specifically with two columns at the following grid intersections.1. 3A2. 3BObjective: Provide details of longitudinal reinforcement for the two columns, from foundation…

 Given that: The etabs file for a G+6 building is provided. Run the analysis and design the RCC shear walls (show in the etabs model). The following challenge deals specifically with the shear wall of size 300x1500 at grid A-11 in the structural model. onjectives:  Extract values of longitudinal steel ratio,…

GIVEN THAT: The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have…

1. Given that Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. AIM:  design and analysis the isolated footing using safe software, and verify the size & reinforcement which provided as per the calcuations.…

1. Giventhat: From the file menu, create a new project (Structural / Architectural / Construction template ) and name the project appropriately. AIM: From the file menu, create a new project (Structural / Architectural / Construction template ) and name the project appropriately. INTRODUCTION TO REVIT SOFTWARE:…

1. Building Information Modelling (BIM)- Building information modeling (BIM) is a process supported by various tools, technologies and contracts involving the generation and management of digital representations of physical and functional characteristics of places. Building information models (BIMs) are computer files…

1. GIVEN THAT Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with…

1. Given that Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level. AIM: To model a Ceiling from the architecture tab above the walls at the first-floor level. INTRODUCTION: The creation of Ceilings within Revit…

1.Why are building codes or standards essential for the modeling/ efficiency of drawings in Revit ? A building code (also building control or building regulations) is a set of rules that specify the standards for constructed objects such as buildings and nonbuilding structures. Building codes specify minimum standards…

1. Given that Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project. Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project. Aim: to set project base point and project shared coordinates…

1. Given that Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School From the above the options of type of structure to build a building,i need to…

1. A) HVAC Systems:HVAC systems are responsible for the regulation of heat, airflow, ventilation, and air conditioning of an entire building. You won’t see the machines when you enter the building but you will most certainly feel the effects of a comfortable and well-ventilated workplace. Here are some of the top…

1. Given that Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below           a. Using 3D model create a section box           b. To create similar doors and windows in a floor plan layout     …

1. Given that Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. Introduction: Dynamo is an open source visual programming language for Revit, written by designers and construction professionals. Its aprogramminglanguage that allows you to type lines of code; while…

1. Given that Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class AIM: To use the architecture/structural project file developed from week 6-8, Export the Revit file…

1. Given that  1. Write the steps involved to upload a .std file through web mail?    2. Name the different materials that can be designed using STAAD Pro.    3. Is it possible to capture images in STAAD Pro? If yes how?    4. Name the three ways by which you can create a model. …

1) Aim:  1. How will you assign Circular section to column?    2. How will you assign Unit system to a .std model file?    3. What are the parameters to be specified while using “Bay Frame” option?    4. Name few codal standards incorporated in STAAD Pro software. …

1. Aim: . 1. State the primary load cases to be considered for design.    2. What is One – Way slab?    3. What is the value of unit weight of structural steel and soil?    4. Name few sections that can be defined using Properties tab in STAAD Pro.    5. Define Primary…

1. Design a Warehouse Building located in Chennai using STAAD Pro Connect Edition. The specification must be as follows     Assume suitable sections for structural elements. Follow IS800:2007, IS1893 and IS 875 Prepare a Design Basis Report for the project Create structural model using STAAD Pro Connect…

1. Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows:      Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity 180…

Design and optimize typical shear, moment and Splice joints in RAM Connection for the following structure modelled in Staad Pro. Design and optimize base plate connection. given condition Structure: A 2D portal frame fixed support spanning 15m with a pitched roof ridge height of 12m, slope of 4 degrees. A uniformly distributed…

Design and optimize typical shear, moment and Splice joints in Staad Connection module for the following structure modelled in staadpro. Generate Report. Design and optimize braced connection (use US standard connections) in RAM Connection.  Structure: A 2D portal frame fixed support spanning 15m with a pitched…

1-Given below is a floor plan of a building. The red lines running East-west are beams supported by the girders spanning North-South between columns. The floor system is 120 mm thick normal weight concrete floor. The floor finish and mech loads on the floor is 3 kPa. The live load on the floor is 5…

Perform Form-finding and structural analysis structure of multiple masts.Given is a two-span beam of spans 5m each. A uniform load of magnitude 5kN/m of variable length to be applied on a beam such that it renders max. possible vertical reactions at A, B & C, and maximum bending moment at midspan of…

Model of a membrane roof with cables. The modeling, form-finding and create the cutting patterns to the structure.Step by step procedureand next go to the geomentry window in that go to cerate beam or add beam option and add beam in the given nodes.create a node at the centre from the right support then consider the height…

A residential society has 200 x 2BHK flats and 100 x 3BHK flats. A typical family in a 2BHK flat has 3 persons/flat and a 3BHK flat has 4 persons/flat. The gross water demand (per person per day in liters) can be calculated by taking the aggregate of the usage for all the below listed activities.ActivitiesConsumption(per…

Conduct the post processing of the results once the analysis is complete. The first task includes, checking the base pressure and settlement beneath the base slab which should be within the limits mentioned in Project-1. If these limits are exceeded then the dimensions need to be increased or decreased so that the base…

1-Summarize the user interface in TSD with the for the following items: - Project Workspace – How to access and usage  Scene Content – Demonstrate the use of scene content  Create two scene views Loading drop list- How to access  Properties windows – how to access and usageAim :…

Create column properties for different types of pedestal members and model in the grids created as per the assignment 1Create column properties for steel columns and model columns in the grid created as per assignment 1.Create beam properties and model primary and secondary beams on the ground floorStep by step procedure…

1. Create beam properties for First floor and model the beamsStep by step procedure: go to tekla software and model upto beam and column intersection then go to manage properties sets under home tab click on new and select the members and then steel members off the auto design option and set to MB350 and click on ok under…

Calculate dead load in design report based on IS code and apply dead load on the modelFinishes of 50mmSlab as per designBrickwall 150mm thicknessRoofing load based on purlin sizeCeiling loading 0f 0.3KN per sq m Step by step procedure:open teklka software and model the beams columns as required positionsspecify the…

40hr project on modelling, analysis & design of a state-of-the-art tall composite building using ETABS software. The composite members to be designed using Comflor softwarea. ModellingThe structural model prepared for the project 1to be used for the project 2.Prepare two distinct structural framing plans (location…

Generate manual wind loading in the design report based IS code as per the following inputBasic wind speed = 39m/sTerrain category 2Based on the above calculation apply the loadings on the model On a separate model generate wind loading using wind wizard