Aim - To find out the mix proportion for M35 grade of concrete with fly ash .   Introduction - i) Generlly Fly ash is added in a concrete to reduced the amount of portland cement.                        ii) It improves the workability and durability of concrete…

Aim - To sketch a G+1 floor residential plan, according to Vaastu Shastra and accordingly calculate the            individual corresponding loads from the members as per IS code .   Introduction - I have considered a plan of G + 1 buliding according to Vaastu Shastra .      …

Aim - i) Create the geometries from P1 to P2 using all the coordinates system methods.          ii) Civil Related Problems -             a) Draw the profile and the trusses using any coordinate system methods.     Introduction - i) In autocad there are…

Aim - To Create Floor Plan , Footing Details and Isometric view using Autocad tools .   Introduction - i) In this assignment various tools like line , polylines , rectangle etc are going to                             used to draw the cross…

Aim - To draw a given sketches in autocad by using various tools like Chamfer , Fillet etc .   Introduction - i) In autocad there are various tools like Chamfer , Fillet , Trim , Rotates etc                         ii) With the help of theses tools we…

Aim - To draw a layout of given residence plan .   Introduction - i) Autocad is most appropriate software which is used to draw a architectural plan .                        ii) For the students and learners , Residential layout is the best plan to practice…

Aim - To create the Column Schedule as shown in figure .    Introduction -  i) The details of Column Schedule drawing is helpful for contractor as well as structural engineer to     understand details about  size of column , reinforcement etc  ii) In given fig Column C1 is provided…

Aim - i) To draw the elevation and details of a wardrobe as shown in fig .          ii) To provide the dimensions and text with the use of layers .   Introduction - i) In give figure Elevation of wardrobe , Carcase elevation , Side elevation are given           …

  Aim - To create the Plan and Sections as shown in the Figures by using proper dimension techniques and          dimension styles to document the project.   Introduction - i) In a given fig . 1st floor 2nd floor and 3rd floor plan is given with dimensions .      …

Aim - To design the layout of a residential building of a dimension 60' x 20 ' with following           drawings -          A) Architectural drawings - i) Floor plan                             …

Aim - i) To create the template by using Text and Attributes .          ii) To create Custom1_titleblock and Custom2_titleblock by using Attributes .   Introduction - i) In Autocad standard templates are given in Start tab                    …

Aim - To create the Kitchen Layout with proper hatch technique and also with proper dimensions           to the kitchen as shown in the figure .   Introduction - i) In give fig there are two plans are given                       …

1)    Aim - 1) Create a layout of plan and sections A of the project in Challenge 7            2) By using Command MV to create the viewport .     Introduction - i) As we have already drawn the Week 7 project by using various commands in autocad.        …

1)   Aim - To create 3D furniture elements as shown in figure .   Introduction - i) In an given figure 3D wireframe model is given as furnitures .                         ii) 3D wireframe model can be drawn by using various coordinate sysrtem  …

Aim - To create a 3D Isometric view of building with plan and elevation.   Introduction - i) An Isometric view is an 3D representation of the object.                       ii) In an give fig , view of building is given with plan and elevations.      …

    Aim - To crerate a 3D model of Residential Building .   Introduction -    i) A 2D plan is created in autocad and it is converted into 3D by using Autocad 3D Modeling . ii) Auotocad is generally used for 2D drawings and then if necessary it is converted into 3D objects by using 3D Modeling …

  1)    Aim - To create a New Project and Name the Project    Introduction - 1) Revit is an Building Information Modeling software and is product of an Autodesk.                      2) It can be useful for Architects , Civil engineer , Structural…

1) BIM -    i) BIM ( Building Information Model ) It is an process supported by various tools , technology and contracts involving the generation and management    of digital representation of physical and functional characterstics of places . ii) It is a highly collaborate process that allows architect…

1)    Aim - i) To create a floor plan with appropriate thickness and material and place it in a plan .          ii) To align the floor plan with grids .     Introduction - 1) Revit is an Building Information Modeling software and is product of an Autodesk.    …

1)    Aim - To create a Ceiling from the Architecture tab to the first floor level .   Introduction - 1) Revit is an Building Information Modeling software and is product of an Autodesk.                         2) It can be useful for Architects…

  1) Necessity of Building Codes or Standard codes in modeling of drawings in Revit -    i) A building code is a set of building codes that are developed and maintained by a standard organisation.  This standard organisation operates    indenpendently of the jurisdiction or area in which…

  1)    Aim - i) To create an Architectural Template           ii) To Set the Project Base point and Project shared coordinate to Project      Introduction - 1) In Revit multiple discipline can work together by linking the project or by using cloud option or Collaborate…

1) Select the type of Structure you want -    i)  As there are 3 options - a) Multi-Unit Residential Apartment                                         b) Office Buildings          …

1) HVAC System and its necessity is the modeling -   i) HVAC device is largely an meeting of diverse varieties of gadget hooked up collectively to offer heating and cooling in conjunction with     indoor weather manage. ii) HVAC structures contain mechanical, electric and I & C additives to offer…

1)      Aim - To use the shortcut keys in Revit discussed in class to complete the following tasks and list them below .   Introduction - 1) Shortcut keys are generally used to save the time and increase the speed of the work                         2) It also increase the efficiency of the work .                      …

1)    Aim - To create a sinusoidal points and create a curve and create a surface out of the curve by using Dynamo    Introduction -  1) Dynamo is a visual programming software which is used to enhance the project process . 2) Its a software that allows you to type lines of code; while also creating…

1)    Aim - To use the architecture/structural project file developed from week 6-8, Export the Revit file to Navisworks cache file.   Introduction -    1) Navisworks is a software tool which is generally used by Management files people . 2) It helps us to coordinate or manage the…

1)  a)   Aim -  Identification of Modes of Failures    Introduction -  i) Generally RC beams fails in Shear failure or in Flexure . ii) The Shear failure occurs when the imposed load exceeds the flexural capacity of the beam's materials, iii) The Flexure failure occurs due to insufficient…

1) To Calculate the Lateral Stiffness -    Assume  L=2h and  EIc = EIb        Step 1) Apply Unit displacement @ U1    `:.`U1 = 1 and U2=U3=0`       `∴K11 = (2*12 EIc)/h^3`           `=(24EIc)/h^3` `∴K12 = (6 EIc)/h^2`…

Aim -    1) To calculate Ln, Mnand Γn for each of the five modes. 2) To calculate the effective modal mass Mn* and the modal mass participating ratio for the 5 modes. 3) To find the base shear for each of the 5 modes of vibration and the combined base shear as per SRSS rule.     1) To…

Q.1)    1)      1) Symmertry -   i) The given framing layout of plan is Symmetrical in nature by seeing the aspect ratio of the framing plan . ii) Because of the symmetrical nature the distribution of load is uniform through out the frame . iii) Which helps in Resisting the Lateral forces…

Q.1)                 Properties                           Case a                 Case b                        …

  Aim - To model a 25 storey building on ETABS with structural properties .     Introduction -  1) ETABS is an engineering software product that caters to multi-story building analysis and design. 2) Modeling tools and templates, code-based load prescriptions, analysis methods and solution…

  Aim  -  To do Comparative Analysis of different storey buildings for Seismic forces     Introduction -    1) ETABS is an engineering software product that caters to multi-story building analysis and design. 2) Modeling tools and templates, code-based load prescriptions, analysis…

  Aim - i) To design the beams in detail from the Etabs 2018.                 ii) To provide the detailing of longitudinal and shear reinforcement for two continuous beams .         iii) To calculate the value of maximum shear force in any one of…

  Aim - To provide the details of longitudinal reinforcement for the two columns (3A & 3B), from foundation to terrace level   Introduction -     1) The factored axial compression stress considered all load combination relating to sesimic loads shall be       limited…

  Aim -  1) To run the Analysis and Design the RCC Shear Wall           2) To extract values of Longitudinal Steel Ratio, Boundary Element Length and Shear Reinforcement ratio from Design results.           3) To provide the elevation drawings of the reinforcement…

  Aim - i) To design a structural model on the basis of provisions from IS 1893 and IS 13920 in seismic zone 5.         ii) To Run a modal response spectrum analysis and check analysis results of the Etabs  .   Introduction -  1) ETABS is an engineering software product that caters to multi storey building analysis. Etabs…

  Aim - To design a square footing for a column size of 400x400 .   Introduction -    i) The footing is a structural member that safely transmits the load of the upper building to the ground, and is the     first construction member of the building. ii) The basic method of footing…

  Aim - i) To  model the isolated footing provided in week 11 challenge on SAFE.          ii) To Analyze and design it to verify the size, depth and steel provided as per calculations.          iii) To model the pile cap on SAFE software .     Introduction…

  Aim - To carryout modelling, analysis, design, and preparation of construction drawings of a G+3 RCC building situated in Guwahati Assam.   Introduction -    1) ETABS is an engineering software product that caters to multi strorey building analysis and design. 2) SAFE represents the state of…

1)     1.1) Steps involved to upload a .std file through web mail?   i) Select STAAD Import from the backstage. ii) The Import from STAAD.Pro dialog opens. iii) Click on General settings to browse and select a STAAD.Pro (*.std) file to import. iv) Select Use Mapping File in Section…

  1.1)   Aim - To assign Circular section to column -    Introduction -  1) Columns are defined as vertical load-bearing members supporting axial compressive loads chiefly. 2) This structural member is used to transmit the load of the structure to the foundation. 3) The factored axial compression…

  1.1) Primary Load Cases to be considered for Design -    i) The Primary Load cases are - A) Dead Load  B) Live load      1.2) What is One – Way slab?    i) If the ratio of Ly/Lx ( Ly = Shorter direction , Lx = Longer direction ) is greater than or equal to 2 , then…

  Aim - To design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition.      Procedure -    DBR - Design Basis Report -   Step 1) Given data -    Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil …

  1)   Aim - i) To Design Warehouse Building located in Chennai using STAAD Pro Connect Edition.          ii) Prepare a Design Basis Report for the project          iii) Create structural model using STAAD Pro Connect Edition        …

 1)   AIM -  To Summarize the user interface in TSD with the for the following items: -           i) Project Workspace – How to access and usage           ii) Scene Content – Demonstrate the use of scene content      …

1)    Aim - To create column properties for different types of pedestal members and model in the grids created as per the assignment 1   Introduction -  i) Tekla Structural Designer is an BIM -integrated model-based 3D software for analysis and design of structures. ii) It includees  modeling,…

 1)   Aim - To create beam properties for First floor and model the beams   Introduction - i) The main function of beam is to carry the loads from the slabs or any secondary beam and transfer it to the column. ii) Inorder to create beam properties for first floor, make sure that it matches the ground…

1)    Aim - 1) Calculate dead load in design report based on IS code and apply dead load on the model             i) Finishes of 50mm             ii) Slab as per design             iii) Brickwall 150mm thickness    …

1)    Aim - To generate manual wind loading in the design report based IS code .   Procedure -  Step 1) Manual Calculation of wind loading   i) Given data-   ii) Calculation Design wind Speed - Vz   iii) Calculation of Design wind pressure - Pz   iv) Calculation of Cpe and Cpi for…

1)  Aim - To summarize study for the bending moment, shear force and deflection diagrams for the elements of the model   Introduction -  i)There are various types of analysis are available in Tekla Structural Designer ii) But in this we are performing 1st Order Linear Analysis   1st order linear - …

1)     Aim - To analyze and design a steel building to 10T CRANE as per IS standard code using TEKLA STRUCTURAL DESIGNER.   Introduction - i) Tekla Structural Designer is an integrated model-based 3D tool for analysis and design ii) It includes interactive modeling, automated structural analysis…

1)    Aim - To setup the cover for RC building    Introduction -  i) As per IS 456 :2000 the covers are provided to prevent the reinforcement from enviromental effects ii) Concrete covering is provided to prevent corrosion of reinforcement bar in RCC. iii) Reinforcement is prone to fire and corrosion…

  1)    Aim - To calculate dead load in design based on IS Code and apply on model.     Introduction -   1) Calculation of Dead load -  i) Slab Load = (Model Slab In Software) ii) Finishes Loading (50 mm Thickness ) = 0.05 x 24 kn/m^2. = 1.2 KN/m^2. ( Area Loading ). iii) Brick wall with…

1)    Aim -  To Generate seismic loading based IS codal provisions and zone II using seismic wizard.       Procedure -  Step 1)  i) Open the previous model ii) Click on Load - Seismic load - Seismic Wizard iii) Add the following parameters based on attachments …

Aim:- To analysis the structure and design reinforced concrete beam and column     Procedure -    Step 1)  i) Open the previous file of week 9 challenge. ii) Click on Analyze - 1st order analysis  iii) At the right side bottom corner - Click on Result View. iv) Select any of the column member…

  1)    Aim: To design the slab and foundation of the model   Procedure -   Step 1)  i) Open the previos Model where we have designed column beam . ii) Again Run the 1st order analysis iii) But Before that change the following properties of slab. iv) Click on 1st order Analysis - Result View…

1)    Aim: To generate report for the steel building design.     Procedure -  i) Open the previous model where we design all the structural elements. ii) Now go to the Report option from the Ribbon bar and select Model report. iii) Select the load cases and combinations summary to obtain report.…

1)     Aim -  i) To develop general arrangement for the RC office building.           ii) Analyze and design the building as per IS standard code in TEKLA STRUCTURAL DESIGNER     Introduction -    i) We have to mark the Position of Columns as shown below…

1)    Aim -To determine the loading on the beam indicated and analyze the beams and draw bending moment and shear force diagram.   Given Data -  i) The floor system is 120 mm thick normal weight concrete floor ii) The floor finish and mech loads on the floor is 3 kPa = 3kN/m^2 iii) The live load on the floor is 5 kPa =…

      Aim - To determine the Shear, moment and Splice joints in RAM Connection for a 2D portal frame is required to be designed.   Given Data -  i) Supports  2D Frame                           : …

    Aim - To design and optimize typical shear, moment and Splice joints in Staad Connection module .   Given Data -  i) Supports  2D Frame                           :    Fixed support ii) Spann     …

  1)    Aim - To model, analysis & design of a state-of-the-art tall building using ETABS software.       Procedure -  i) Open the Etabs Software  ii) Enter the IS Code details    iii) Edit the Story Data    iv) Creation of Grids    v) Creation…

  Aim - To model, analysis & design of a state-of-the-art tall composite building using ETABS software.      Procedure -  Open the Project 1 file which we have saved      Step 1) Grid Assignement    Step 2) Material Properties    Step 3) Frame Properties …

      Aim - To create a user-defined member and test the cross-section for tensile load.     Procedure -    Step 1)  i) Initially Open the RFEM software  ii) Click on New Project iii) Enter the Project details as shown below    iv) Click on Add - ons   iv) Once…

    Aim - To Model of a membrane roof with cables.     Procedure -    Step 1)  i) Initially Open the RFEM software  ii) Click on New Project iii) Enter the Project details as shown below    iv) Click on Add - ons   iv) Once you enter the details , Click on Okay and…