Concrete mix design for M50 grade concrete: 1. Data collection      Grade designation = M50 Assume,       Type of cement     = OPC 43 grade conforming to IS 8112      Maximum nominal size of aggregate = 20 mm size of aggregate      Workability …

        Sketched the G+1 Residential plan as per Vaastu Shastra( 2BHK). Dimension of floor area of the Building is 11m x 9m. The total height of the building is 8 m + 3 meter height of staircase room on terrace. The building located in Chennai.   To find the self weight of the structure 1.column…

1.AIM       To draw a given diagram by using the line and various commands in AutoCad. PROCUDURE First to create a new sheet in auto cad and set the required format for units of measure. For this diagram mostly required to using a different measurement of lines can be used to draw objects. Select…

1.AIM        To draw the cross-section of Load bearing wall over spread footing to use the software of Auto CAD. PROCEDURE To open the new sheet and type,, U’’ in command bar to change the units into meters. Type,,L’’ to give the line command and to give the dimensions…

1.AIM       To draw the given plan using the various  commands in Auto CAD. PROCEDURE To open the new sheet from application manager. TYPE ..U ‘ in command bar(enter) and to set up the units in meters with the proper decimal. To observation the diagram, to select required commands. TYPE…

1.AIM  To draw  the plan of ground floor building with 2bhk  using the various commands in Auto CAD. PROCEDURE To create a new drawing sheet . Type ,,UN’ to set the units of current format of measure.( FEET and INCHES) Type ,,LIMITS’ to set the maximum dimension limits on the particular page.…

1.AIM       To create the column  schedule  using the various commands in Auto CAD. PROCEDURE To create a new drawing sheet . Type ,,UN’ to set the units of current format of measure. Type ,,LIMITS’ to set the maximum dimension limits on the particular page. Type ,,L’ - Line commands…

1.AIM  To draw  the Elevation and Details of waredrobe  using the various commands in Auto CAD. PROCEDURE To create a new drawing sheet . Type ,,UN’ to set the units of current format of measure.( MILLIMETERS) Type ,,LIMITS’ to set the maximum dimension limits on the particular page. Type ,,L’…

AIM      To draw the  PLAN and SECTIONS using the various commands in Auto CAD. PROCEDURE To create a new drawing sheet . Type ,,UN’ to set the units of current format of measure. Type ,,LIMITS’ to set the maximum dimension limits on the particular page. Type ,,L’ - Line commands allows…

1.AIM         To draw the Floor Plan, Elevation and section of Residential Buildings  using the various commands in Auto CAD. PROCEDURE To create a new drawing sheet . Type ,,UN’ to set the units of current format of measure.( FEET and INCHES) Type ,,LIMITS’ to set the maximum dimension…

1.AIM        To draw the Templates of title block as per industry standars  using the various commands in Auto CAD. INTRODUCTION The title block of the drawing is usually located on the bottom or lower right hand corner. It contains all the information necessary to identify the drawing…

1.AIM        To create the layout of kitchen as per industry standards using the various commands in Auto CAD. INTRODUCTION OF HATCHING The hatch command in AutoCAD is used to fill patters inside an enclosed area. The patterns are hatched, gradient and solid fill. The gradient patterns are…

1.AIM        To create the layout of the plan and section using the various commands in Auto CAD. INTRODUCTION OF LAYOUT Layout viewports are objects that display views of model space. This is importance to create a separate view, scale and place them in paper space on a layout. On each layout,…

1.AIM         To create a 3D Furniture elements using the various commands in Auto CAD. INTRODUCTION BY 3D VIEW The process of creating a mathematical representation of any surface of an object in three dimensions by using special software. A 3D model can even be represented as a two dimensional image…

1.AIM     To create a 3D Isometric view of the building with plan and elevation using the various commands in Auto CAD. PROCEDURE To create a new sheet from application of Auto CAD. Go to the setting and to change the view of the page from Drafting to 3D modeling. Type ,,UN’ to set the units of current…

AIM     To create a Plan, Elevation, Isometric view and 3D Render view using the various commands in Auto CAD. INTRODUCTION BY 3D VIEW The process of creating a mathematical representation of any surface of an object in three dimensions by using special software. A 3D model can even be represented as a two…

1.INTRODUCTION OF REVIT REVIT is an engineering configuration and documentation programming application. It is a building information modeling software for architects, landscape architects, structural engineering, mechanical, electrical, and plumbing engineering, designers, and contractors.    Step by step procedure…

1.BIM BIM is a process in which all the information of the 3D buildings Models are linked and incorporated to produce a comprehensive 3D model. The BIM is supports to Revit by creating the data based model of architectural designs, structural designs and MEP designs.     Features of BIM Revit is a single application…

1.AIM        To draw the floor plan layout with aligning of GRIDS by using the REVIT Software. PROCEDURE To create a new page with Imperial architectural . To save file at appropriate name. To create a conceptual layout of residential unit of our plan. First to desire the acquired land area…

1.AIM        To create the model of ceiling above the top of the walls at first floor level. INTODUCTION Ceiling is an overhead interior surface that covers the upper limits of the buildings. It is not generally considered a structural element, but a finished surface concealing the underside of the…

1.Why the building codes or standards essential for the modeling/efficiency of drawings in Revit A building codes is a set of rule to regulate the construction activities across the country. From the national building code list the groups that will be essential to you when you being modeling in Revit. We have to model…

1. Open an architectural template. Using the Manage tab set project base point and project shared the coordinates for the project. AIM         To create an architectural template and to set project base point and shared coordinates by using Revit software. PROCEDURE To create a new sheet with Architectural…

1. Select the type of structure you want to build from one of the three below    Multi unit Residential Apartment    Office Buildings    School  ANSWER         I want to select the model of Multi unit Residential Apartment.     Residential Apartments It is…

1. What are HVAC systems? Why are they essential in modeling of buildings. Heating, ventilation and Air-conditioning (HVAC) is designed to achieve the environmental requirements of the comfort of occupants and a process. The basic components or equipment of an HVAC system that delivers conditions air to satisfy the thermal…

1. Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below     ANSWER Using 3D model create a section box is BX To create similar doors and windows in a floor plan is CS. To reduce the thickness of lines visible in plan views is TL. To apply override setting to a…

1. Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve AIM       To create a set of sinusoidal points and create a curve and create a surface out of the curve using Dynamo PROCEDURE To create a new file of Architectural template. Saved the file at…

1. Use the Architectiral/Structural project file developed by you in week 6 to 8. Export the Revit Architecture and structural        model to navisworks cache file following the export settings discussed in class. AIM        To Export the architecture and structure model to Navisworks…

1. What is mode of failure or damage of beams in the figure above? Would you characterize the case as damage      or as a  failure? Are the damages repairable? Elaborate. ANSWER       Beam and Column frames connection failures. This cracks are forming when a structure occurring undesirable…

1. Compute lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The               system has 3DOFs as shown. Assume L = 2h, Elb = Elc. ANSWER                          …

A five storey structure with 5 translational DOF is shown here. Each storey has mass 'm'. The eigen value problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, has been derived. ANSWER                          …

1. Comment on the layout of the framing plan concerning earthquakes resistance in the two horizontal directions X or Y ( dots are columns, lines are depict beams). Look into aspects of symmetry, redundancy, and bi-directional stiffness and Ductility.               AIM   To describe…

1. The building shown, 20 x 30m in plan, has column on a 5 x 5m grid and shear walls( with dimensions shown in m, 250mm in thickness) in three alternative arrangements. (a, b, c), all with the same cross sectional area of the shear wall. Compare the three alternatives, taking into account the restraint of floor shrinkage,…

1. Model a 25 story height building on ETABS with structural properties as specified below. Ground floor or plinth floor level cab be taken at a height of 1.5 meters from the base. Each of the successive 25 storys has a story height of 3 meters.                      …

 Comparing the different parameters of structure.   ANSWER Structure – A: Open the new model. Set the units at Indian parameters. Next to prepare the story and Grids formation. The grids spacing at 4m in X direction(4 bays) and 4m in Y direction(3 bays). To add the material properties of concrete in M30.…

ANSWER STEP 1 open the model of G+4 building To choose the load combination about a structure. select design > Load combination > set to concrete frame design click ok.                                      STEP 2 After,…

ANSWER AIM      To provide the reinforcement details of Longitudinal and Shear Reinforcement for the Two columns from foundation to Terrace level.   PROCEDURE STEP 1 open the G+4 building model. To define the Concrete frame Design tool. Run the analysis and check the details about the structure. choose…

ANSWER AIM      To provide the Reinforcement detailng of given structural wall of G+6 building. PROCEDURE STEP 1 To open the G+6 model building in Etabs.' next, we do check and RUN the analysis.                          STEP 2 Next, we have…

The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have been provided:…

Design a square footing for a column size of 400x400. The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 metres below E.G.L. Participants are free to go for either a tapered or stepped footing. Besides the total axial load, also…

In this project, participants will get to experience the entire design process from modelling, analysis, design, and preparation of construction drawings. The architectural drawings of a G+3 RCC building is provided. The following information on the building is to be used: Location – Guwahati, Assam Function –…

1. Summarize the user interface in TSD with the for the following items: - ANSWER Project Workspace – How to access and usage  To open the new File on TEKLA software. Then automatically we get the project workspace and we can access it. Scene Content – Demonstrate the use of scene content we get the project…

1.Create column properties for different types of pedestal members and model in the grids created as per the assignment 1 ANSWER Open the new file on Tekla software. To analyze and note down the layout dimension, Grid formation about a Given Plan model. To Draw the Grids along X and Y direction at an appropriate location…

1. Create beam properties for First floor and model the beams AIM    To add the beam properties as reference of Given plan by using Tekla software PROCEDURE Go to manage property sets. To create new Beam properties at MB300 at primary beams. Go to structure for choosing the First floor Then model the beam at…

1.Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab as per design Brickwall 150mm thickness Roofing load based on purlin size Ceiling loading 0f 0.3KN per sq m AIM     To add the Dead load of finishes and brickwall load to the model by using Tekla…

1. Generate manual wind loading in the design report based IS code as per the following input Basic wind speed = 39m/s Terrain category 2 AIM       To Generate the wind load to a model as per Indian standard code reference. PROCEDURE Data Basic wind speed, Vb = 39m/s. Terrain category = 2 Class…

1.Summarize your study for the bending moment, shear force, and deflection diagrams for the elements of the model AIM  To analyse the structure and summarize study for bending moment, shear force, and deflection diagrams for the elements of the model and also display these parameters for our model. PROCEDURE To open…

Analyze and design a steel building to 10T CRANE as per IS standard code in TEKLA STRUCTURAL DESIGNER. Refer the attached plan and elevation. Provide bracings and moment connection for lateral stability.  Consider dead, live, equipment and wind loading. Consider the brick wall loading for 150mm thick and 1.5 KN per…

1. Setup model for RC building design and based on following parameters for cover MEMBERS IN CONTACT WITH GROUND ABOVE GROUND Column 50mm 40mm Beam 30mm 25mm Slab 30mm 25mm Pilecap 75mm   Foundation 50mm   ANSWER To open the new file in Tekla software. Save the file at the appropriate location. For Rc Building…

AIM     To calculate the Dead load, live load, and wind load at manual with a reference of Indian standard code and apply to the model by using TEKLA Software. PROCEDURE To add the load cases of all categories. To calculate the  Dead load calculation of Finishes, Brick wall, services. To add the Load at…

1. Generate seismic loading-based IS codal provisions and zone II. Any other data you can assume and input accordingly. AIM   To generate seismic loading based on Is code by using tekla software.  PROCEDURE To add the load cases of Seismic factor as per Indian standard. Go to Load > Seismic load > seismic…

1 Based on the analysis design RC column and beam. AIM    To design the RC Column and beam based on the analysis of structure. PROCEDURE To open the model of Rc frame building. Now we consider the model to process of Analysing the whole frame, then to finding the Failure of elements will occur. Then, to correct…

1. Design the slab and foundation of the model. Outline the thought process for designing of the elements (column, beam, slab and foundations)   AIM     To design the slab and Foundation design of Pile foundation As per Indian standard By using the TEKLA Software. PROCEDURE To open Our model at 3D view.…

1. Generate report for the steel building design from challenges 1 – 6 along with the loading summary AIM    To Create a report for steel structure building With the Loading summary. PROCEDURE To open the Tekla Steel building model. To open the Report Tab. To choose Under the report tab, we find the select…

Develop general arrangement for the RC office building. Analyze and design the building as per IS standard code in TEKLA STRUCTURAL DESIGNER. Refer the attached plan and elevation. The building to be designed for dead, live, wind and seismic loading. Report of each member to be generated and extract drawings for structural…