2R Robotic Arm (MATLAB) Aim :       To write a program in MATLAB to simulate the forward kinematics of a 2R Robotic Arm in 2D and create an animation file of the plot. Objective :        1) The mathematical process to calculate the position of end-effector by using the angles…

 Solving Second Order ODE-Simple Pendulum (MATLAB)  Aim :      To write a program to solve the second order ODE of motion of a simple pendulum with damping. Objective :      1) Solve the second order ODE of a simple pendulum into first order ODE.      2) write a program…

Genetic Algorithm (MATLAB)   Aim :       write a code optimise the salagmite function and find the global maxima of the function in MATLAB. Objective : Explaination about genetic algorithm and syntax of ga function. write the salagmite function to find the global maxima in matlab. write a progarm for plot F maximum vs…

Parsing NASA thermodynamic data   Aim :      Evaluate the thermodynamic properties such as Specific heat(Cp), Enthalpy(H), Entropy(S) by using the given NASA thermodynamic file. Objective :           1) write a program that extracts the 14 coefficients from given THERMO.dat file.          2) Calculate the specific heat,…

Rankine Cycle simulator (MATLAB)   Aim :        Create the rankine cycle simulator and calculate the state poins and plot the T-S and S-H using MATLAB. Objective :   Study about Rankine cycle concepts.  Calculate the state points of Rankine cycle using matlab.  plot T-S and…

  Aim :       1) To make simulink model for a doorbell using solenoid block.       2) To use thermistor to sense temperature of a heater and turn on/off the fan.   1) Door Bell : Theory - Solenoid :       Basic definition, A solenoid is a device comparised…

  Aim :     1) Implement control logic of a "washing machine" using stateflow as per the given condition.     2) Make the simulink chart for gear shifting logic as per the given codition. 1) Washing machine - stateflow      As per the given codition  If the power suppy…

 BAJA ALL Terrain Vehicle (ATV) Model    Aim :      To carry out the system level simulation of an all terrain vehicle and preparing a technical report for explaining the model and properties and results. Objective :    To prepare a technical report on BAJA ATV explaining model properties…

  Aim :         To develop a forward energy based fuel consumption model of a conventional vehicle in MATLAB and simulink. Objective : Understand the concept of forward energy based fuel consumption model of a conventional vehicle. To understand the functioning various vehicle componets including…

  Aim :   To develop a forward energy based fuel consumption model of a P1 Hybrid electric vehicle in MATLAB and simulink. Objective : Understand the concept of forward energy based fuel consumption model of a P1 Hybrid electric vehicle. To understand the functioning various vehicle components including…

Tabulate chemistry reaction of Lithium-ion Battery   Aim :         Explain the material and chemical reactions occuring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells and compare the difference between each type of li-ion Batteries based on their characteristics.…

State of charge Estimation   Aim :          To simulate the BMS and run the various test case from hardness dashboard and write a detailed report on the results. Objective : Explain about coulomb counting and how BMS implements coulomb counting for SOC. Rnu the simulation test the 3 cases…

Mechanical design of a Battery pack   Aim :       To configure the Mechanical design of Battery pack for 18 kWh energy with the Lithium-ion cells and state our assumptions. Theory :  ANR26650M1-B cell :        This LiFePO4 battery is a A123's high-performance Nanophosphate…

Thermal modelling of battery pack   Aim :      To simulate the 10 cell series lithium ion battery model and explain the thermal effects and compare life cycle performance at various temperatures using MATLAB. Objective : Create the simulink battery model for 10 series lithium-ion cell with thermal effects.…

Benchmarking   Aim :    To prepare and explanining the concept of Bench-marking and suggesting the suitable vehicle among the comparision for Me.D.S. Pughazhyendhii. Objective : Expaining about Bench-markimg. Compare different vehicles banch-mark. Suggesting the suitable vehicle among the comparision. Theory…

Underbody Coating   Aim :      To prepare about Under-body coating and its purpose, and its types and its pros and cons. Theory : purpose of doing Underbody  coating - Corrosion :       Corrosion is defined as the destructive and unintentional degradation of a material caused…

Hood Design   Aim :       To design the automotive hood component which includes the outer panel, inner panel, hinge as well as latch assembly with the necessary reinforcements following the master section with the design guidelines and parameters. Objective :  Explaining the concepts of Latch…

Section Modulus calculation and optimization   Aim :         To create the section for hood and calculate section modulus and optimization the section modulus. Theory :        Section properties involve the mathematical properties of structural shapes. They are of great use in structural analysis and design. Note that…

Wheel Arch gap - Calculations   Aim :      To calculate the wheel arch gap at required points and check whether the car passes the European standard. Objective : Study about the different wheel arch gap standards. Draw the lines at the required angle and points for the European standard. Measure the…

Fender Design   Aim :       To design the fender by using the give master section for trip area and design the sill, Bumper, Baffle and A-Pillar mount  according to the engineering standards. Objective : Study about fender and its type and the parameters need to follow.  Design the trip…

Roof Design    Aim :        To design the roof and its reinforcements from the given styling surface received. After the design is done calculate the heat distortion criteria and snow load calculations. Objective : To develop the essential flanges and reinforcements using roof styling as the…

Design of Backdoor   Aim :      To design the Backdoor using the provided styling surface with the different design methodlogy and necessary embosses and reinforcements using NX cad. Back Door :      The backdoor or Tailgate is the panel that covers the boot (or trunk) of an automobile.…

Base Bracket Design   Aim :      To create the base bracket plastic component through the given class A surface and create the required Tooling axis and perform the Draft analysis on the model. Objective : First create the required correct Tooling axis and preform the Draft analysis on the given class…

Switch Bezel Design   Aim :         To create the Switch Bezel plastic component through the given class A surface and create the required Tooling axis and perform the Draft analysis on the model. Objective : First create the required correct Tooling axis and perform the Draft analysis on…

Coin Holder Design   Aim :        To create the coin holder plastic component through the given class A surface and create the required tooling axis and perform the Draft analysis on the model. Objective : First create the required correct Tooling axis and perform the Draft analysis on the class-A…

Bumper   Aim :        To create the Bumper plastic component through the given class A surface and create the required tooling axis and perform the Draft analysis on the model. Objective : First create the required correct tooling axis and perform the Draft analysis on the class-A surface. Create…

Core and Cavity Design for switch bezel   Aim :        To create the core and cavity blocks for the switch bezel we have already designed as the solid part. Objective : Create the required Tooling axis by using the bisecting method. Perform the Draft analysis on the solid model. Create the parting…

Ribs and Screw Boss creation    Aim :    To create the Rib for the drill handle concidering the design rules for rib creation and Screw boss creation and then perform the Draft analysis for the final component. Objective : Create the Tooling axis by using the bisecting method. Design the class-B and…

Dog House Creation Aim :       To create the Dog house for the Door Trim considering the design rules for Dog house creation and then perform the Draft analysis for the final component.Objective :Create the Tooling axis by using the bisecting method.Design the class-B and class-C surface and join…

Door Trim - Engineering Features   Aim :       To create the Door trim lower plastic component through the given Class-A surface and attach the engineering features such as Locaters and Heat stakes and perform the Draft analysis. Objective : Create the Tooling axis by using the bisecting method. Design…

A Pillar Design with master section   Aim :        To create the A Pillar Design with the master section given as the intersection sketch with the Class A surface and create the tooling axis and perform the Draft analysis for the final solid part. Objective : Create the required Tooling axis by…

Assembly workbench    Aim :        To create the assemblies according to the given 2D Drawings create the parts and then assemble them together. And create the Drafting for each parts. Objective : Create the parts with the given 2D Drawing and assemble them together. Create the Drafting for…

Development of Door trim panel   Aim :      Create the Door trim panel by using the given class A surfaces and by refer the master section for thickness. And also create the required engineering features like Dog house, Flanges and Heat stakes. And assemble all parts using constrains. Objective : Create…

Assemble the Butterfly valve   Aim :      To assemble the butterfly valve by using the sub parts created and apply the GD&T to the Butterfly valve assembly drawing. Created sub parts :                               …

Casing Design    Aim :      To create the casing sheet metal as per the given dimension and model by using the various sheet metal tools in NX cad. Objective : To Design the casing by using the sheet metal tools. And create the Drafting file for the created casing sheet metal part  Design…

BOX Assembly    Aim :       To Design the box assembly sheet metal as per the given dimension and model by using the various sheet metal tools in NX cad. Objective : Design the main bottom part using the sheet metal tools. Design the top cover part using the sheet metal tools. Design the Side…

Sheet metal part for odd shape  Aim :     To create the sheet metal part from the odd shape and add some features such as flanges,jogs and bends and also create the drawing file for it.Objective :To create the solid part first and from that design the sheet metal.Then create the extra features such as flanges, jogs and…

Bracket Design    Aim :         To create the bracket sheet metal part by using the various sheet metal tool in NX cad platform. Objective : Design the sheet metal bracket and add features such as bead and holes. Design approach :                                                Design procedure :          First create the…

Metal Bracket 2 Design    Aim :     To design the sheet metal component of metal bracket by using the various features in the NX cad platform. Objective : Design the base and flange for the metal cracket by using sheet metal features. Add the extra features such as advanced falnge, holes, normal cutout, gussets in the…

American Chopper 3D model creation   Introduction :        This project is about learning to use a 3D modelisation software called solidworks. made by Dassault system, solidworks has become an industrie standard when it comes to mechanical design and modeling. this solidworks is used in the manufacturing…

Yacht 3D Model creation    Introduction :        This project is about learning to use a 3D modelisation software called solidworks made by dassault system, solidworks has become an industrie standard when it comes to mechanical design and modeling. This solidworks is used in the manufacturing…

Design and Simulation of four cylinder Engine   Aim :        To create the four cylinder engine each single parts and assemble them and simulate the model using solidworks software. Objective : To design the saperate parts by using minimum sketch tools and features in solidworks CAD software.…

Flow over a cylinder   Aim :      To simulate the transient state flow over a cylinder by using the flow simulation tool in solidworks software. Objective : To run a baseline simulation and then calculate the Reynolds number. To increase the Reynolds number by a factor of 20%,40% and 100% then run the…

Flow over a Airfoil    Aim :      To simulate the air flow over the airfoil of the NACA0017 model by using the flow simulation tool in solidworks software. Objective : To simulate the flow over the Airfoil from the NACA0017 model data. To obtain the Drag force and the Lift force For the various angles of the airfoil model.…

Engine valve analysis    Aim :      To create a 3D model of a flow bench and run the flow analysis by using the flow simulation in the solidworks software. Objective : Create the 3D model of the engine valve system. To obtain which is the good grid mesh level. To find the velocity, pressure and…

Centrifugal pump design and analysis    Aim :       To design the centrifugal pump and analysis the performance of the centrifugal pump by using the flow simulation in solidworks software. Objective : To create a 3D model of a centrifugal pump by using the part modelling tool. To simulate the water flow in the centrifugal…

Define the 3D model as Electrical Connector   Aim :       To download the connectors and clips CAD file and define that 3D model as the electrical connector by using the Electrical part design workbench in the CATIA V5 software. Objective : Download the below listed 3D cad model of the connector and clip from the te.com.…

 Define p clamp, Backshell, Corrugated tubes in Electrical design   Aim :      To download the clamp and Backshell CAD file and define that 3D model as the electrical part by using electrical design workbench in solidworks. And create corrugated tubes and add them in catalogue. Objective : To download…

Harness layout Routing in Electrical Workbench    Aim :    To create the harness layout routing in electrical workbench by define the electrical part and routing bundle and make the product.                           Objective : To define…

Route the Harness layout in Electrical workbench   Aim :         To route the given harness layout by using the required connecters and for the given maping in the electrical workbench in catia v5.                       Objective : To define…

Flatten the Harness Assembly   Aim :      To create the harness assembly file for the given map and create the flatten by using Electrical Harness Workbench and create the Drawing file for it.                                                     Objective : Create the electrical assembly as shown in figure using the mutiple…

Engine wiring Harness    Aim :         To route the wiring harness on the 16V type engine by concidering the all packaging rules, industry best practices and apply the production covering to the required wiring. And finaly prepare the Flatten Drawing for wiring. Objective : To create…

Car Back Door wiring Harness   Aim :       To route the wiring harness on the car Back door assembly by concidering the all packaging rules, industry best practies and apply the production covering to the required wiring. And finaly prepare the flatten Drawing for wiring. Objective : To create…

Motion Analysis of Internal Geneva Mechanism Objective :         The main objective of this project is to conduct a motion study for dynamic visualization, identify timing and synchronization issues, study of contact force, angular force, angular displacement and angular velocity of an "Internal…

Planetary Gear Assembly   Aim :        To Create Planetary gears assembly using part modeling and import gears from design library. After assembling gears analysis the input and output gear speeds by using the motion study in solidworks software. Objective :       1) To import/design and assemble planetary gears, ring…

MBD of Piston Assembly   Aim :    To create all the parts of piston assembly and assemble them in assembly workbench and run the motion analysis using solidworks motion study. Objective : To create all parts of piston assembly and assemble. To run motion study analysis for the following cases.                     To plot…

Simulation on IC Engine Valve Train   Aim :      To create and assemble the parts of the IC engine valve train. And then perform the motion study for valve linear motion and contact force for this assembly. Objective : To create and assemble 3D model of the Cam, Push rod, Rocker arm, valve stem and valve. To perform motion…

Windshield wiper simulation Aim:   To create model and assemble the windshield wiper assembly and analysis the wiper movement. Objective:To create the 3D part of the windshield parts using part workbench.Then assemble the parts of wiper assembly using assembly workbench.Simulate the wiper movement to…