Aim- To plan a G+1 residential building according to vaastu shastra and calculate loads coming on it as per IS codes. Objectives- To plan a G+1 residential building as per Vaastu shastra. To study planning of building as per Vaastu shastra. To list the structural drawing required to provide at the site. To calculate…

AIM-  Create the geometry of given pictures in AutoCAD using all the coordinates system methods. Introduction to Coordinate System :- There are Four AutoCAD coordinates system :- Absolute Coordinate System Relative Rectangular Coordinate System Relative Polar Coordinate System Direct Distance Entry Absolute Coordinates…

AIM:- To draw the cross-section of Load bearing wall overspread footing to use the software of Auto CAD. C1 INTRODUCTION:  The cross section of load bearing wall over spread footing using AutoCAD is created by Lines and Rectangles. The procedure and result should be written after creating the cross section of load…

AIM:  To draft the following geometry by setting the unit of measurement as decimal in AutoCAD Software INTRODUCTION:  THIS DIAGRAM IS IN DECIMAL UNITS  PROCEDURE: 1.STEP: SET THE UNIT IN DECIMAL UNIT-> PRESS UN->SET DECIMAL AND PRECISION -> "0.00". 2.STEP:  SELECT LINE COMMAND -> SPECIFY…

1.AIM Residence Plan: Sketch the layout of a residence as shown in Figure 1. Consider all dimensions as a reference to sketch the unit plan. Also, the text in the layout is only for reference. Assume the missing dimensions. Also, refer to the schedule for the size of the doors. PROCEDURE: 1.STEP: TYPE UN ->SELECT …

AIM: Create a column schedule as shown in the figure using AutoCAD. PROCEDURE: 1.STEP: PRESS UN -> SELECT ENGINEERING -> SELECT SCALE INCHES -> PRESS OK 2.STEP: SELECT LINE COMMAND -> SPECIFY FIRST POINT -> DRAG 0 DEG -> DISTANCE 24'. 3.STEP: CONTINUOUS LAST POINT -> DRAG 270 DEG -> DISTANCE 10'…

  1. AIM: To create the elevation and details of a wardrobe using AutoCAD. INTRODUCTION: The elevation and details of a wardrobe using AutoCAD is created by Lines and Circles. The procedure and result should be written after creating the elevation and details of a wardrobe.   PROCEDURE: 1. PLAN SELECT…

*AVERY DIMENSION GIVE IN THE DRAWING   1. AIM: TO DRAW THE 1ST, 2ND & 3RD FLOOR PLAN USING AUTOCAD   PROCEDURE: FIRST SELECT UNIT COMMAND -> SELECT DECIMAL> SCALE MILEMITER > PRECISION 0.0 > PRESS OK SELECT XLINE COMMAND > SELECT VERTICAL LINE > SPECIFY FIRST POINR> PRESS ENTER SELECT…

*AVERY DIMENSION GIVEN IN THE DRAWING AIM: Design and Draft a layout of a residential building with the Plot Size: 60’x20’(18.3m x6m) Facing East. Introduction: In this challenge, I have drafted the above-mentioned drawing i.e, Design and Draft a layout of a residential building with the Plot Size:…

1. AIM- TO CREATE THE TEMPLATES BY USING AUTOCAD INTRODUCTION-> AUTOCAD IS SOFTWARE.  IT IS USE FOR SKETCHING AND DRAFTING THE DRAWING COMMAND USING TO CREATE THE TEMPLATES Line- Start the Line command by clicking the Line button on the Draw panel on the Ribbon, or by entering L and then pressing Enter. Draw line…

1. AIM: TO CREATE THE LAYOUTS OF THE KITCHEN AND PROVIDE HATCHES PATTERNS USING AUTOCAD. INTRODUCTION:  HATCHING-: For this, AutoCAD uses “hatches” that represent solid masses and materials to be used and incorporated within the design when it's built. ... The hatch command in AutoCAD is used…

1. AIM- To create a layout of plan and section A in the project using the template Tutorial-mArch.dwt in a scale as given in the Figure. INTRODUCTION-  Layout plan-  In architecture and building engineering, a floor plan is a drawing to scale, showing a view from above, of the relationships between…

1. Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing. AIM- CREATE THE 3D MODEL OF FURNITURE ELEMENT SHOWN IN THE FIGURE. INTRODUCTION- AutoCAD- AutoCAD stands for Computer-Aided Design.  AutoCAD is software developed by the company Autodesk. It allows you to draw and edit digital…

1. AIM:- To create a 3D Isometric view of the building with plan and elevation.   INTRODUCTION-: AutoCAD- AutoCAD stands for Computer-Aided Design.  AutoCAD is a software developed by the company Autodesk. It allows you to draw and edit digital 2D and 3D designs more quickly and easily than you could by…

  Aim:- To create a Three-Dimensional Model of the residential building with a rendered view using AutoCAD.   Introduction:- 2D Wireframe Model:- A wireframe model is a skeletal description of a 3D object. There are no surfaces in a wireframe model and it consists of only points, lines,…

AIM:- TO DEFINE THE BASIC TOOL OF RIVET USING GIVEN POINTS INTRODUCTION:-  Autodesk Revit is a building information modelling software for architects, landscape architects, structural engineers, mechanical, electrical, pumping (MEP) engineers, designers and contractors. The original software was developed…

1) What is BIM? Summarize the features of BIM and the benefits of using BIM over 2D CAD tools. BIM is a new process and methodology by which a team of architects, engineers, and conductors work collaboratively to design and build a commercial building utilizing the same database and computer model. This allows the team…

1. AIM:-  Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, use the floor tool under the architecture tab and select the floor with appropriate material and thickness using the property browser to create a layout in the Ground floor level. Align the floor plan…

1. AIM:- To create the first_floor ceiling using Revit Software. Introduction:- Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level Procedure:-  GO TO ARCHITECTURE TAB > SELECT CEILING COMMAND> SELECT…

1) Why are building codes or standards essential for the modeling/ efficiency of drawings in Revit? The main purpose of building codes is to provide minimum standards to protect public health, safety, and general welfare as they relate to the construction and occupancy of buildings and structures. Model building codes…

1. Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project AIM:- TO CREATE BASE POINT AND SHARED COORDINATES FOR ARCHITECTURAL TEMPLATE. INTRODUCTION:- The project base point can be used to establish a reference for measuring distances and positioning…

AIM:- TO MODEL THE BUILDING WHICH DRAFTING, DESIGN, AND ENSURE THE SAFETY OF ALL THE COMPONENTS. MAKE SURE EVERY RESIDENTIAL UNIT IS FULLY FILLED BY THE MODEL OF THE PROJECT.  INTRODUCTION:- I select the multi-unit Residential Apartment.  I model an 8 multi-unit Residential Apartment. Which carry G+4 floors…

1) What is HVAC system? Why are they essential in the modeling of buildings? AIM:- to define HVAC and Importance in building. Explanation:- HVAC stands for Heating, Ventilation, and Air Conditioning. HVAC refers to the different systems used for moving air between indoor and outdoor areas, along with heating and cooling…

1) Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below           a. Using a 3D model create a section box           b. To create similar doors and windows in a floor plan layout         …

1. Using Dynamo creates a set of sinusoidal points and creates a curve and creates a surface out of the curve. Aim:- TO create a sinusoidal points curve and surface using dynamo  Procedure:- Go to select new template> select architecture temoplate> press ok Go to the manage tab and select Dynamo open integer…

1. Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class Aim:-  To export the Revit file into the Naviswork file. INTRODUCTION: Export the Revit architectural and structural…

What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate Q.1 Aim:- To identify which type of mode failure occurred and its causes. It is Rpairable or not. Introduction:-  In this question, we identify the types of failure causes, and whether they are repairable…

Que :- 1. Differentiate Static analysis and Dynamic analysis with proper representing pictures (30 marks) AIM:- To Differentiate Between Static analysis and Dynamic analysis Ans:-    Static Analysis:-  In Static analysis we analysis static load means “a force that has constant size, position and direction…

Aim:- To compute the values of seismic parameters based on the given structural data To compute Ln, Mn, and Γn for each of the five modes from the given Question. To calculate the effective modal mass Mn* and the modal mass participating ratio for the 5 modes.  To obtain the base…

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, and lines depict beams). Look into aspects of symmetry, redundancy, and bi-directional stiffness and ductility. Figure No. 1.1 AIM:- To determine the layout of the framing…

Question 1: The building shown, 20 × 35 m in the plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into…

                                                                                           …

                                                                                       Project 1 - Comparative…

                                                                                           …

                                                                                           …

                                                                                           …

The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have been provided:…

Design a square footing for a column size of 400x400. The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 metres below E.G.L. Participants are free to go for either a tapered or stepped footing. Besides the total axial load, also…

1. Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. AIM:- To design the isolated footing using safe. Introduction:-  In the field of civil engineering, isolated footings play a crucial role in providing support…

                           Project 2_Design & Analysis of a Hostel building at Guwahati, Assam Aim:- To Design and Analysis the of G+3 (RCC) hostel building in ETABS and Foundation in CSI SAFE. Introduction:- In This Project design process…