AIM: create 1D elements with using given cross section and DOF   OBJECTIVE: created the 1D elements of bar,rod and beam with using following dimensions    a. Rod element:- with only translational DOF and RBE2 link    Cross-Section: BOX- Dimension a= 12 mm          …

AIM: evaluate quality critera of the hood component. OBJECTIVE: below  mentioned quality criteria of the hood with using hypermesh          TARGET ELEMENT LENTH 5mm           S.N Quality Criteria  1 Aspect Ratio  2 Skewness 3 Warping 4 Taper …

AIM: To create a tetra mesh for housing OBJECTIVE: creat a tetra mesh of housing model with using below mentioned measurments                     Elements sizes: Min- 2mm, Target- 5mm,Max- 7mm  Tet collapse: 0.15 PROCEDURE:   1.FOR HOUSING MODEL: importb housing…

AIM:create connectors between thevarious paerts and attach the remainig parts of the given model OBJECTIVE: Create connector and Attach the various parts of the given model  1. Right_Rail_2 & Front_truss_1:- Seam-Quad(angled+capped+L) 2. Left_Rail_2 & Front_truss_1:- Quad elements 3. Front_truss_2,…

                                                   project-1: meshing and assign thickness of the car side door INNER PANEL     AIM:Evalute the quality criteria and mesh the component…

                                                                    PROJECT-2 : MESHING AND ASSIGN THICKNESS OF SPARE WHEEL HOLDEL     AIM: Meshing…

AIM: Cleanup the geometry and meshing and assign the thickness of the practice,clip repair,mounting bracket OBJECTIVE: Clean the geometry. Extract midsurface. Clean midsurface geometry. Ignore holes less than dia 5mm. Create 2D mesh with target length 5mm, min 3.5mm max 7mm. And assign proper thickness, by creating a generic…

AIM: SOLUTIONS OF THE ABOVE QUSTIONS 4. CHANGE THE RUN TIME IN ENGINE FILE    termination time is stress wave can  moving from one end of the rail to the other during impact -this will require a termination time equal to the time it takes for the sound to travel the length of the rail. 5. . 6.Change…

AIM:The main aim is Comparison of results with base simulation and improved shell element properties. OBJECTIVE: Compared the base results with recomanded properties for 2D shell elements. Recommended properties: Parameters    Ishell =24   Ismstr=2   Ish3n=2   N=5   Ithick=1…

AIM: Run the simulation given cases and plot the graphs and compare results  ABSTRACT: Run the simulation different cases create animation of each case plot the curves opf accepable energy compare the results  PROCEDURE: CASE1: Import the model Run file 000  File > IMPORT > SOLVER DESK > IMPORT…

AIM: Run the simulation of crash tube various cases and caompare the results for all cases ABSTRACT:  Create the mesh for the bumper assembly Joint the parts in bumper assembly using with spot weld Run the simulation of crash tube in various cases plot the graphs contact forces,internal energy and Create compare…

                                                                  FRONTAL CRASH ANALYSIS-BIW AIM: To perform a frontal crash Analysis of the givein model.…

                                    NEON SIDE CRASH ANALYSIS ON BIW MODEL AIM: To perform a Neon side crash-BIW Analysis of the givein model. OBJECTIVE: Check unit system and either follow [Kg mm ms]. Create appropriate interface…

      CONSTRUCTION TREE:                               

1. 2. 3. 4. 5. 6.

  AIM:To generate the Draft Analysis for the given Switch bezel model. PROCEDURE:   CREATING TOOLING AXIS:   1.Find the tooling direction. Of the switch bezel.this part had only 3 walls. 2.Extract the base surface and create point on the surface. Insert the axis system  3.Creating intersection on the…

  AIM: To generate the draft analysis of the arm rest model. PROCEDURE: CREATE TOOLING AXIS: Create point on the middle of the hole. And insert the system axis. Create intersection on the XY plane.and draw a line on the two walls and create bisecting line using with two lines And create another intersection on the…

AIM:Create a coin holder plastic component with using class A surface.and perform the draft analysis on the model.                 PROCEDURE: CREATE TOOLING AXIS: Insert the geometrical set and name it as tooling axis. Extract the base surface. and create point on the surface Create…

AIM:Create the Core and cavity blocks for the switch bezel. PROCEDURE: CREATING PARTING SURFACE: Extract the class A surface up to 15cm. Un hide the b surface and trim with both surfaces. create a parting line using with multiple extract option.around the class solid surface of the switch bezel. DESIGN CORE BLOCK: Create…

    AIM: Create the rib for the coin holder folling the design rules. PROCEDURE:    Draw a line on the base surface of the coin holder with using portion sketch. Construct the line with using axis. and extrude the this line and add thicknig for this surface. add thickness of the rib 0.4*thickness of…

AIM:Create the boss and Dog House for the Centre console coin holder following the design rules. PROCEDURE: SCREW BOSS: General Guidelines for Bosses:   Draft  - 0.5 degrees on walls of boss   Thickness -  Typically 40%* of the nominal wall at the base.   Height to Diameter Ratio…

                                            APPLIQUE FIXED TO THE MAIN DOOR COMPONENT     AIM: Create the Base Bracket Plastic component through the given Class-A surface. PROCEDURE: APPLIQUE…

  AIM: To create the Plastic design and the Engineering features from the Master Sections and generate the Draft Analysis for the given B Pillar Class A model and Final Component.  PROCEDURE: 1.Check for any openings in the given model Door Applique by using BOUNDARY. In BOUNDARY > select edges - select the…

                                            DESIGN AND DEVELOPMENT OF CAR INTERIOR DOOR TRIM AIM:           Creation of car interior door trim…

BENCHMARKING: BENCHMARKING INVOLVES THE COMPARISON BETWEEN SIMILAR PRODUCT SERVICES OR PROCESS IN SOME DIMENSIONS OF PREFERENCES. BENCHMARK COMPARES THE DIFFERENT TYPE OF SIGNIFICANT. LIKE  Comparing processes within the organization.  Comparing to other organizations.  Specifically compared to direct competitors.…

UNDERBODY COATING: Underbody coating provides long-term protection from corrosion to a car's underbody. It also protects parts like internal body panels, frame rails, and other inner cavities that are not physically accessible but are prone to corrosion. In Indian road conditions, a car's underbody…

                                                                     HOOD DESIGN   INTRODUCTION: HOOD: The car’s hood consists of an inner…

                                      AIM: calculate the section modulus using the formula S = I/y. Use the Section from your Hood design.      Use the Section from your Hood design and calculate the section…

                                                       ROOF DESIGN AND OPTIMIZATION AIM: creation of a roof ditch area the tool opening angle is only 3 degrees. For the Given…

                                                                 DESIGN OF CAR BACK DOOR      AIM: Use the provided styling surface to come…

                                                                            WEEK-2   OBJECTIVE:  1. Make a Simulink…

                                                                  WEEK-4 OBJECTIVE:   Implement control logic of a “washing machine”…

                           Case study of system-level simulation of an all-terrain vehicle   AIM: To study and analysis of the Baja ATV Terrain vehicle using the Simulink model. OBJECTIVE: To prepare a technical report of BAJA ATV explaining…

ADVISOR : ADVISOR was created in the MATLAB/Simulink environment. MATLAB provides an easy-to-use matrix-based programming environment for performing calculations while Simulink can be used to represent complex systems graphically using block diagrams.ADVISOR uses three primary graphical user interface(GUI)…

  What is the difference between the mapped and dynamic models of engine, motor, and generator? How can you change the model type?  How does the model calculate miles per gallon? Which factors are considered to model fuel flow?  Run the HEV ReferenceApplication with WOT drive cycle. Change the grade and…

                                               WEEK-6(EV DRIVETRAIN)  1.  Which types of power converter circuits are employed in an electric and hybrid electric vehicle?    AC…

                                                                 DC MOTOR CONTROL BJT H-bridge:   An H-bridge is a simple circuit that lets you control…

                                                                       WEEK 11 BRAKING          1.For a defined driving…

                                                Project-1: Powertrain for aircraft in runways   1.the total weight of various types of aircraft The aircraft gross weight  is the total…

                                                            Final Project: Design of an Electric Vehicle                …

                                                                       Solving second order ODEs   AIM: Simulate the transient behavior…

                                                                           Genetic Algorithm     Genetic Algorithm: A genetic…

                                             Project 1 - Parsing NASA thermodynamic data   AIM: The thermodynamic data for various species are studied and the coefficients of temperature in the characteristic…

                              American Chopper Moto  Design and Assembly    Objective:   The objective of this project is to understand and demonstrate the design philosophy of a retro American chopper motorcycle model using…

Radar Mast :                                                                            MODELING AND ASSEMBLY OF YACHT  …