Mix design for m35 grade concrete -  1)Grade - M35 Max size of aggregate  = 20mm Min cement content - 340 kg/m^3 (table 5 IS 456:2000) Max water cement ratio - 0.45 (Table 5 IS 456:2000) Workability - 100-120 mm slump  Method of concrete placing = Pumping Degree of supervision = good type of aggregate - crushed angular…

structural drawings provided on site - centre line drawings footing and column layout with reinforcement details column schedule with reinforcement details plinth beam layout drawings first floor beam layout with reinforcement details first floor slab layout with reinforcement details lift pit adn headroom reinforcemnt…

Q1) For P1 Aim - to create P1 geometry in Autocad using absolute coordinate system procedure - 1. open autocad 2. select decimal units to create the given geometry (keeping DYNMODE OFF) 3. select the line command. specify first pt as 2,1 4. next pt as 8,1 5. next pt as 8,2 6.next pt as 3,2 7. next pt as 3,5 8. next pt…

Aim - To draw the CS of load bearing wall over spread footing in Autocad. Procedure - 1. Open Autocad. Select "New" in the opening window before starting drawing. 2. Select the line tool and keep the "Ortho mode" on to get lines which are 90 degree. 3. Follow the measurements provided to draw the C.S of load bearing wall.…

AIM - to draw the given figure using decimal units. Procedure - 1. select the line tool and give it a length of 3 units. 2. in the command box, enter dimension as @2.12<45 3. enter next dimension as 2.83<45 4. in the negative X direction draw the line with a dimension of 2 units 5. connect the line to the starting…

A1  Aim - To sketch the layout of residence plan as shown in figure 1 procedure -1. select a pont and draw a horizontal line of 25' 2. offset it by 9" to show the wall thickness 3. from the starting pt of this line draw a vertical line of 43'6.5" and offset it by 9" to show wall thickness. 4. by using offset, trim…

A1) Text and diagram wasn't clear in the question paper so i couldn't complete it.   A2)         A3)     A4)   A5)  

A1to to draw the elevation and details of wardrobe as shown   result -      A4) to sketch column details as shown   reuslt -     A3) Aim - to create the kitchen layout using proper dimension   result - 

Aim - to create the plan and section shown using proper dimensions. procedure - line command, offset command and block tool have been used to create the plan. One single unit has been created each time according to dimensions mentioned. the thickness of exterior wall is take as 230mm and internal wall has been taken as…

aim - to create an architetural plan sextion elevation for a 60' x 20' plot tools used- line command, trim, xline, extend, offset, copy, erase, hatch, layers, dimensions, text 1. architectural plan   2 column layout     3 footing layout     side elevation      

A1) AIm - to create the templates as shown in figure   result -           A2) Aim - to create door types of warehouse using standard dimensions and convert them into block tools used - line command, offset, dimensions, text, trim, erase, hatch. procedure -  draw the frame of the door…

A1) Aim - to provide layout of kitchen as shown and provide hatches wherever required. tools used - line command, offset, dimensions, trim, erase, extend, hatch etc. procedure - 1. the external dimenions of the walls are created and then the wall thickness is given. 2. from the wall thickenss 600 mm line is marked and…

a1)aim - Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt procedure-1. in the layout 1 section, use the page setup command to set the page size to A1 and the setting to portrait. 2. using the mview comand, specify the corner point and give a height of 400mm…

A3)     A5)  

a1) aim - to create 3d isometric view of buildingprocedure - 1.create layers for the wall and windows2. draw the line plan in XY plane according to layers allotted.3. use boundary command on walls4. mark them as region5. use extrude command to give a height of 10'6. only the wall layers will be extruded.7. create a rectangle…

aim - to create 3 dimensional residential builsing model procedure - create the plan and elevation in 2d with window, door openings and projections. assign them in the layers according to the elements to be shown in the drawing. using boundary command mark the regions and extrude the walls selectively to the height desired…

A1) aim - to create a new project and name the project appropriately. procedure - open revit app on your pc click on the file tab to open the drop down menu and click on new to open the options. click on new to open the menu and select project as the option to open a selection box for the project. select the construction…

A1) BIM stands for Building Information Modelling. It is a process which helps architects, engineers and construction professionals think and improve the way they design and carry out projects. It allows sharing of information through Cloud data Environment. it can be used for designing a project or making renovations…

A1 Aim - to create floor from architexture tab and fill it with appropriate material and thickness.   procedure - open revit and then open the project. from the architecture tab, select floor then select architetural floor then select the line tool to create a connected boundary for the floor     create the boundaries…

A1) aim -  to create a ceiling over the first floor   procedure - open the project in revit once it is open, in the architeture tab click on the option     click on the sketch ceiling button     use the rectangle option to draw the outline of the ceiling above the first floor walls  …

A1) The National Building Code of India (NBC), a comprehensive building Code, is a national instrument providing guidelines for regulating the building construction activities across the country. It serves as a Model Code for adoption by all agencies involved in building construction works be they Public Works Departments,…

A1 aim - to use the Manage tab set project base point and project shared coordinates for the project   procedure - open new architectural template     draw grids and name appropriately     Specify coordinates at grids     select collaborate tool and save file     select collaborate…

A1 Type selected - multi unit residential apartment (3 storeys) procedure -open the structural template in revit and draw the grids       place the columns and beams on first floor level      add isolated footing to the columns by using at columns option and selecting all at once    …

A1 HVAC systems are responsible for the heat, airflow, ventilation and air conditioning of the building. these machines are not visible directly but their effects are felt as soon as you enter the building. They are essential in the modeling of building because - they control the climate and make changes to the temperature…

A1 shortcut keys in revit   Using 3D model create a section box - BX To create similar doors and windows in a floor plan layout - CS To reduce the thickness of lines visible in plan views - TL To apply override settings to a floor in the model section view - VG To increase the range of visibility in a plan view- VR…

A1 aim - Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve.   open architecture template in revit and from the manage tab open dynamo   in the search panel, search for code block start block has value 5 second one has value 300 last one has value 1  …

A1 aim - Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class   procedure - open the architetctural models createdclick on the export option in the file tab and select…

A1 Image a shows beam column joint. The failure is at the beam. The damage is cause by not providing sufficient cover to the beam. The improper mixing and vibration may have also been the reason for the  failure of the beam.   image B shows chipping off like phenomenon of concrete. it is due to honeycombing.…

A1 we are going to use the stiffness influence coefficint to solve the problem. the 3x3 stiffness matrix of the structure is known as equilibrium condition. the DOF is 3   Step 1 U1=1, U2=0, U3=0 stiffness matrix calculate as K11=24EIc/h^3 K12=6EIc/h^2 K13=6EIc/h^2   Step 2 U1=0, U2=1, U3=0 K21=6EIc/h^2 K22=4EIc/h+4EIb/L…

A1 symmetry -  the positioning is good in both directions. It has good uniformity also. districution of masss and stiffness along the plan has good symmetrical aspects. redundacy - the energy dissipation across the structure is very low which causes unreliability. it will cause uneven distribution of energy in case…

A1) A)   restraint of floor shrinkage - in figure A since shear walls are on all four sides, it has good control of shrinkage of floor because all four corners are held by shear walls to experience shortening. In figure B, the corners might undergo shortening or shrinking since the floor is given shear walls only…

open the ETABS software and input the following data Use built in settings option to fill the data     after model initialization select custom grid setting and then input the grid data as follows     after this edit the story data. input 26 storys, 1 will be the plinth level at 1.5m and the story height…

Aim - To model and analyse the different kinds of buildings and conduct a comparitive analysis between the models based on different factors.   Introduction - Buildings oscillate during earthquakes whoch causes inertia forces to be developed in the building. The intensity and duration of oscillation and the amount…

Aim - To run the analysis and design the RC moment resisting frame for the given ETABS Model Procedure - 1. open the model in ETABS and check it from the Analyze tab   2. Check load combinations on the model     3. Start the beam design by selecting Start design/check option as shown     4. Select…

Aim - to provide details for logitudnal reinforcement for two columns from foundation to terrace level procedure - 1. open the G+4 ETAB file 2.click concrete frame design tool 3.select display design info option 4.choose design output as longitudnal reinforcement   5. clcik elevation view 6.in set view options uncheck…

Aim - to run the analysis and design the RCC shear walls   procedure - 1. open the file in ETABS And run the analysis 2. run analysis on the model     3. run design check       4. select identify PM-failure             5. select display info and choose pier reinforcing…

Aim - to create a model of the give G+7 architectural model which must comply with the provisions of IS 1893 and IS 13920   Procedure - Create the grids in the ETABS model     2. input material data         3. add framed section properties              …

Aim - to model the isolated footing. analyze it for pile group to be used, depth of pile and longitudnal steel on top and bottom face in both directions.   procedure - 1. open SAFE and input the following data     Single footing to be selected next subgrade modulus = FOS x SBC/settlement = 3x150/0.05 = 9000…

AIM - to perform analysis in ETABS and SAFE for the given hostel building in Guwhati, Assam Procedure - 1. Select new model, choose metric system and code details   2. edit grid data as per the plan   3. edit story data 4. defin the material properties from define tab   for M25 concrete   For rebar…

A1) aim - to summarize the user interface of TSD Project workspace - 1. after opening tekla structural designer, click on NEW on the left side top hand corner to open project workspace project workspace is now active   2. Scene Content - to open scene content, open windows tab and select the scene content options…

A1 Aim - to ccreate column properties for different types of pedestal members and model in the grids created as per the assignment 1   procedure - open TEKLA software and model the levels as shown below     grid lines are created according to the section   pedestal modelling   place pedestals in…