Mix design for M35 grade concrete with fly ash grade designation M35 type of cement OPC43 grade conforming IS 8112 type of mineral admixture: fly ash conforming Is3812 maximum nominal size of aggregate 20mm minimum cement content 320kg/m^3(from table 5 IS 456:2000) maximum water-cement ratio 0.45 workability: 100mm…

  the wind load is neglected building height is below 10 meters.   

AIM: -  To Create the geometries from P1 to P2 using all the coordinates system methods. use the Line tool to create the geometries. Where it's required to use the circle tool geometries. INTRODUCTION: coordinate systems are absolute coordinate system relative coordinate system in relative coordinate system classified…

Aim: to draw a floor plan, footing details and isometric view using AutoCAD using tools of line tool.  INTRODUCTION: offset is creating the distance one line to another line at distance of given value  fillet: the fillet is creating the curve at edges on both sides  chamfer: chamfer also create the…

AIM: To draw a Residence Layout, Seating plan, Toilet and Utility room plan using AutoCAD    1.ANS    select the construction line vertical and horizontal  offset 9" offset 6'9" offset 9" offset 6'8" offset 4.5" offset 11'0" offset4.5" offset 4'6" offset 4.5" offset 12' offset 9" trim fillet radius…

AIM: to draw the Drafting of various geometries using Chamfer, Fillet tools in AutoCAD    1.ANS  take line command specify the point  @3<0 @2.12<45 @2.83<135 @2<180 close  take offset enter distance of 1.5 repeat offset distance 1 and 2.5  select the circle and diameter of 0.80…

1.ANS  AIM: To creating a column schedule as shown in figure to prepare a using AutoCAD tools    introduction:  Create a column schedule with the help of lines. Also, insert text with the help of DText command or Single Line text. Use font name: romans.shx; Height: 8”, Justify: Left   PROCEDURE:…

1.ANS  AIM: To Draw the elevation and details of a wardrobe using AutoCAD  introduction:   draw the details of wardrobe plan, front elevation, carcase elevation, section-1 and section-2, side elevation     using the tools line tool, trim, offset, layers and what we required tools are…

AIM:  To Creating the Plan and Sections as shown in the Figures Introduction: Using proper tools in AutoCAD and dimension techniques and dimension styles to documenting the project. Assuming the sizes of the doors and windows as per construction standards. Referring the sections for stair details    Procedure:…

AIM: Design and Draft a layout of a residential building INTRODUCTION:  Design and draft a layout of a residential building with the following details: a. Plot Size: 60’x20’   b. Orientation- Facing East    c. Develop the following: 1. Architectural Drawing (Floor Plan, Elevations, and Sections) 2. Structural Drawing (Column,…

1.ANS Aim: TO create the template as shown in figure. introduction: using text and block and wherever required used to create the templates   using tools rectangle, line, multi-line text, block, attributes PROCEUDRE:  SELECT the text and write text and create the block and select the attributes and given…

1.ANS  AIM: TO create the kitchen layout as shown in figure    Introduction:  kitchen layout drawing as shown in figure t draw by using AutoCAD Procedure: 1.open AutoCAD and set units as metric  2. select the rectangle and draw the dimensions of 4300x 3200 3. select the offset and wall thickness…

1. ANS  AIM: to create the multiple view ports as weak 7 challenge   steps: 1. open the auto cad and select the units as metric  2. click on start button and open the weak 7 challenge created the plan and section  select the new layout select the new template as  Tutorial-mArch.dwt and…

1. ANS  AIM: Creating the 3D furniture element as shown in figure  procedure  1. open auto cad and set units as imperial and setting set as the work space model is 3D basic  2. select the line command  3.using the absolute coordinates system     select the line enter the first point…

1.ANS  AIM: to Creating a 3D Isometric View of the building with plan and elevation given.                                                                …

AIM: Creating a 3-dimensional model of the residential building with a rendered view. PROCEDURE:open AutoCAD and set the units and limits select the construction line and draw the line select the offset and distance is 300mm select the trim and extra lines are trimmed select the fillet and…

1.ans  AIM:   From the file menu, create a new project (Structural / Architectural / Construction template) and name the project appropriately procedure: open Revit 2023 software and select the new    in the ribbon tool bar click the file and save the tempelate with approperiate name  save…

1.ans  BIM and its benefit over 2d CAD tool.BIM is Building Information Modelling.It is a concept created by Autodesk.Revit helps in achieving BIM as a process. Features in BIM: BIM is divided into 2 concepts:a) Coordination: is the key feature in BIM. It helps in coordination of multiple disciplines. Like Revit offers…

1.ANS  AIM: creating the floor of residential building  procedure: select the floor tool in architecture tab and select boundary line as rectangle and drawn the floor thickness is 200mm  material is given the wood cherry assigned   2.ans  AIM: adding the walls on given layout using Revit architecture…

1. ANS  AIM: creating the celling in first floor level  procedure: select the weak 3 challenge saved file and open  select the celling on first floor level of wall is drawn by the pickup lines  and edit the material as per requirement  after place the celling added the celling rounded type lights …

1. BUILDING CODES of standard modelling. A model building code organization is a set of building codes that are developed and maintained bya standard organization. This standard organization operates independently of the jurisdiction or area inwhich the building code standards are being developed. Local government or councils…

1.ANS AIM: Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project PROCEDURE: open the architectural template and select the grids draw the on longitudinal and traverse  select the mange tab and set the shared coordinates point at intersection is zero …

1.ANS  Selected the type of structure is office building          2.ans  My building is constructed in the commercial area, Anantapur, Andhra PradeshMy building is constructed in the plain area(geographic)Infront of my building there is a two-lane road with the width of 4.5m.As per…

1.) Ans HAVC SYSTEMS: heat ventilation and air condition (HAVC) it is a technology of indoor environmental comfort its goal is to provide thermal comfort and acceptable indoor air quality important part of structure EESENTIALS IN BUILDING MODELLING: controlling the overall climate of the building  it enhances the…

1) AIM: Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below           a. Using 3D model create a section box           b. To create similar doors and windows in a floor plan layout         …

1. Ans  aim: Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. procedure:  open the Revit and go to manage tab and click the dynamo  open the dynamo in new file  search bar searches the integer slider, point.by coordinates, code block, math.…

1.ans AIM: Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class  procedure:  open the Revit software and open the architectural template and click the file…

 1a ANS: observations: concrete crushed and the reinforcement is exposed concrete spalled beyoond the reinforcement which may be a sign of rupture  beam top portion looks safe because of the flange advantages from slab  the crack develops from bottom to top means rebar yielding occurs in support bottom only  …

1.ans   Differentiate Static analysis and Dynamic analysis variation of load with time in dynamic analysis but not Varey in static analysis because of the load is slowly taken but the dynamic analysis is load variation with respect to time, it changes under vibrations  motion cannot be disregarded two additional…

1. Ans Investigation of the framing plan with respect to Symmetry in X-direction:  If we split the plan vertically half, it will look mirrored. So, we  conclude the given plan is symmetric in X-direction.  Investigation of the framing plan with respect to Symmetry in Y-direction:  If we split the plan…

 1.ans 2.ans  Issues in the given Framing plan: Indirect lateral load Transfer in X directions- The beams are connecting to another beams which is ineffective during lateral load transfer. In such conditions, the primary beam is prone to shear failure.  Eccentricity-The longer the distance between center…

AIM:  ETABS modelling of a 25 Storey building procedure: 1.first open the new modal  2.modal initialization setting use built-setting = metric -SI steel section data base- India concrete code -IS-456:2000 steel code-IS-800-2007 3.custom the girds and Storeys required numbers and set the master Storey as…

AIM: creating the 25 Storey building desing and analysis of using Etabs software and find the natural time period,mode shape of oscillations, etc. procedure: open the new modal and set the customized grids and storey  add the plinth level as 1.5m and each storey is 3m, 2 storey building modal-A  define the properties,…

AIM: Reinforcement detailing of beam for Etabs output procedure: 1.open the ETABS software and open the given link file and run analysis  2.click on the concrete design frame and check all the beams and columns get the longitudinal reinforcing details    shear reinforcing details:   at the grid A mid…

aim: reinforcement detailing of columns from ETABS output procedure: 1.open the weak 7 challenge g+4 Storey building file  2. select the roof level and set all stories and select the columns at grid-A and grid-b at grid line-3 3.click the right button and selected objects only and run the analysis 4. 5. click the…

AIM: Analysis and design of RCC shear walls in the model using ETABS Procedure: 1.download the attchement file and open in Etabs  2.set the 3D view and select the plan view as terrace and apply okay  3.select shear wall at grid A-11 and show visibility is set show only selected objected 4.elevation view set as…

Aim: structural modeling of G+7 Storey building using Etabs procedure: open the new model and edit the grid system and Storeys step-2 define the materials as rebars HYSD415, concrete is M25 grade step-3 define frame sections column, beam and slab, shear wall c-600x600mm b-400x500mm salb-150mm thickness shear wall thickens…

aim: design the isolated footing  Design a square footing for a column size of 400x400. The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 meters below E.G.L. Participants are free to go for either tapered or stepped footing.…

1. Aim: Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. Procedure: Open the new model file and select single footing  given the all required values as I get calculation values    Define the material…

In this project, participants will get to experience the entire design process from modelling, analysis, design, and preparation of construction drawings. The architectural drawings of a G+3 RCC building is provided. The following information on the building is to be used: Location – Guwahati, Assam Function –…

1. 1ans: click on Staad pro software open it and select the share and send mail  2.. Name the different materials that can be designed using STAAD Pro concrete aluminum  steel  stainless steel  3.. Is it possible to capture images in STAAD Pro? If yes how? Ans. go to post processing and select the take…

AIM: 1.1 How will you assign Circular section to column? Introduction: Column are the vertical member in the Structure that can be of varying size in dimensions The circular section of column is provided at the upper floor of the building for the better load carrying and access purpose Procedure: Create the model in the staad…

AIM: 1.1 How will you assign Circular section to column? Introduction: Column are the vertical member in the Structure that can be of varying size in dimensions The circular section of column is provided at the upper floor of the building for the better load carrying and access purpose Procedure: Create the model in the staad…

    ANSWERS:    1. 1. State the primary load cases to be considered for design. Ans: Dead Load ,Live Load ,Snow Load, Seismic Load, Wind Load   2. What is One – Way slab? Ans: The one-way slab is a slab, which is supported by parallel walls or beams, and whose length to breadth…

 1. Prepare a Design Basis Report for the project location= Bangaluru building floors =  g+6+R plan dimensions = B= 25m                             L= 16m storey height = 3.5m  typical storey height = 2m soil type= hard soil use =…