Aim-Calculate the concrete mix design for M50 grade concrete without fly ash. Introduction-In this we will see the whole procedure of calculating mix design for M50 grade. Final result will show us the                           exact proportion of cement…

Aim-To prepare a G+1 floor residential plan, according to vaastu shastra and calculate loads. Introduction-In this we are going to see a plan according to vaastu shastra. Where should be kitchen, living room etc.                   Assume, Area=286 sq.m                                Column size=0.25*0.25m              …

Aim-To draw P1 and P2 drawing using all co ordinate system. Introduction-Here we are drawing a sketch on autocad software with line commamd using all 4 types of co ordinate system. Procedure- 1.Take imperical template with decimal dimesions 2.Type l in command and a start a drawing  3.Co-ordinates methods are (i)Absolute…

Aim-To draw a sketch of C.S. of load bearing wall over spread footing by using autocad. Introduction-Here are we using line, rectangle command and some snap setting. With the help of provided dimensions which will be shown in drawing. Procedure- -Take rectangle by rec command of 0.9,0.5 -Now take a line command and start…

Aim-To draw a sketch by using autocad. Introduction-Here we are going to use command line, circle. Procedure- -Take a line command specify 1st point anywhere -Start drawing towards right 3, @2.12<45, @2.83<135, then towards left 2 and close the drawing. -From starting point take line command @1.5,1 as a center of…

Aim-To draw a residence plan according to given sketch. Introduction-In this all dimensions are feet and inches. Some missing dimensions are assume. Procedure- -Set limit of template and units in feet and inches  -XL enter horizontal and vertical -Trim extra lines create corner point -Take offset of 9" of both lines…

Aim-To create a column shedule Introduction-In this we use font name Roman.shx, height 8", justify left Procedure- -Set unit in feet and inches and dimension also. -Specify 1st point anywhere and create a table by line command -dt enter for text with 8" height  -Rotate text as per given diagram -Trim excessive lines…

Aim-To draw elevation and details of wardrobe. Introduction-In this wardrobe details given in different elevations, front elevation, side elevation, carcase elevation. Here sections are also provided in detail. All dimension are in mm. Procedure- -Set limit maximum is 100,100 and minimum is 0,0 -Set unit in mm and dimension…

Aim-To create a plan and section by using autocad Introduction-All dimensions are in mm. As per standard doors and windows sizes are used.                    D=1000mm  D1=750mm  D2=900mm   Procedure- -Set unit, limit and dimesion style also -XL enter…

Aim-To draw a design residential building with floor plan, elevation, section and footing plan with column and beam details. Introduction-The residential plan has east facing orientation and plot size is 18.3mx6m. And it is single storey residential building. The drawings provided are floor plan, front elevaion, section,…

Aim-To create template and save it as a block with name: Custom1_titleblock and Custom2_titleblock. Introduction:All dimensions are in mm. Assuming sizes for this according to paper size. Procedure- -Set unit, limit and dimension style. Here am creating new dimension style with text font:Time New Roman CE. -Start drawing…

Aim-To create a kitchen layout with blocks and hatching as shown in figure. Introduction-In this below and above counter plan of kitchen layout is given with hatching and blocks. Here door and windows are in block provided. All dimension are in mm.                    -D1=1000x2100 …

Aim-To create a layout of plan and section A of the projrct in challenge-7 by using template. Introduction-Here Challenge-7 plan is taken as a reference to create viewports and layout with template.  Preocedure- -Set unit in mm, limits, dimension style -XREF enter, attach dwg challenge-7, bind ok and then explode…

Aim-To create a 3D furniture as shown in figure by using Autocad. Introduction-All dimensions are in feet-inches. Here we are going to show different 3D profile. Procedure- -Set sheet in 3D modelling -Set unit in Engineering, inches -Set limit and dimension styles -Draw rectangle of @3',2' make a region and extrude it…

Aim-To create 3D isometric view of the building with plan and elevation given. Introduction-All dimensions are in feet & inches. In this 3D elevation done by using autocad. Procedure- -Set unit in engineering with precison 0'0" and inches -Set limit, i.e. lower is 0'0",0'0" and upper is 50'0",50'0" -Set dimension style…

Aim-To create a 3D of resedential building with a rendered view. Introduction-This plan is G+1 resedential building.                   -All dimension are in mm.                   -Thickness of outer wall is 230mm and inner wall is…

ANSWERS:- Aim-To create a new project and name the project appropriately. Introduction-In Revit we can create various template such construction, architectural, structural etc. Here i am creating                             Architectural template.…

Answer: 1]BIM -It is acronymn for Building Information Modelling. -It is a process of creating and managing information for a built asset throughout its lifecycle—from planning and design to construction and operations. BIM is used for creating and managing data during the design, construction, and operations process.…

Aim-To create a floor, assign material to it and give thickness using property browser, Introduction-In this using week-2 project file i.e.Challenge-2 file to creating a floor. We can assign diffrent material to floor as Revit provide us so many options. We can manage thickness of floor by creating duplicate of inbuilt…

Aim- To model a ceiling from architecture tab above wall at first floor level. Introduction-Here we are using model from week 3 challenge. Ceilings help create an enclosure and separation between spaces, they help to control the diffusion of light and sound around a room and help prevent the passage of sound between rooms.…

Answers:- 1]A building code is a set of rules that specify the minimum standards for constructed objects such as building structures. The main purpose of building codes are to protect public health, safety and general welfare as they relate to the construction and occupancy of buildings and structures. The building…

Aim-To open an Architecure template and set project base point and project shared coordinates for the project. Introduction-A Revit project has internal coordinates for all the elements that compose the model in a project. Those coordinates are known to this project only. This is sufficient if you have a standalone model…

Answer:- 1]I want to build Office Building. 2] Modelling Requirements for the Office Building as per NBC based on the type of Structure. Type of Occupancy: As per NBC part 4 Fire and Life safety Clause No: 3.1.6 Business Building Sub division E-3: Information Technology Park F.A.R: Type 2 Construction Allowable FAR:- 2.9…

Answers:- 1] HVAC stands for heating, ventilation, and air conditioning systems. This system is responsible for heating and cooling your home and includes products like furnaces, air conditioners, heat pumps, ductwork, thermostats, and other home comfort controls. An HVAC system combines the processes of heating, cooling,…

Aim-To use shortcut keys in Revit Introduction-Thre is shortcut kry for almost every command, here we are going to see some of example of shortcut keys and hw we used it in Revit                   -Here i am using Challenge-7 Architectural model file. procedure- -Open Revit…

Aim-To create a set of sinusoidal points and create a curve a surface out of curve by using Dynamo. Introduction-Dynamo is a visual programming tool that works with Revit. Dynamo extends the power of Revit by providing access to the Revit API (Application Programming Interface) in a more accessible manner. Rather than…

Aim-To export the Revit architectural and structural model to the Naviswork cache file. Introduction-Autodesk Navisworks Manage software is a comprehensive project review solution that supports coordination, analysis, and communication of design intent and constructability. Multidisciplinary design data created in a broad…

Cracks-The majority of cracks occur when the building or its components or the material of which the building is made upon it’s subjected to forces that are greater than those which it can withstand. Cracks may occur in different components of a building due to- • External applied force in a different component…

Answers- 1] Static Analysis               -It is in  linear state and does not vary with time -It does not depend on time  -Static force does not change in sixe, position or direction -In this inertia forces are produced due to their masses -Example: Hydraulic lifting cranes,…

Answer: Given Data-    T1=2 sec             T2=0.6852 sec   T3=0.4346 sec    T4=0.3383 sec T5=0.2966 sec     Adding first two modes Mass Participation Ratio we get,     =0.88+0.09     =0.97 To achieve minimum 90% of modal mass…

Answers: Question 1: (a)Symmetry:- 1] Investigation of the framing plan concerning Symmetry in X-direction: If we split the plan vertically in half, it will look mirrored. So we conclude that given plan is symmetric in the X-direction. 2] Ivestigation of the framing plan concerning Symmetry in the Y-direction: If we split…

Answers: Question 1: Case (a) 1.Restraint of floor shrinkage Observation-Full Restraint at all corners Conclusion-It has higher restraint to shrinkage thus it will lead to cracks in floor. 2.Lateral stiffness Observation-It has comparitively lower lateral stiffness in both x and y direction 3.Torsion with respect to vertical…

Aim-To model a 25 storey building on ETABS with structural properties as specified. Introduction- Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. Structural Element Sizes  Beams : 300 × 400 mm …

Aim-To do Comparative study of different storey buildings for Seismic forces. Introduction- Structural Element Sizes  Beams : 300 × 400 mm  Columns : 400 × 400 mm  Slab : 150 mm thick  Material Properties  Grade of Concrete : M30  Grade of Steel Reinforcement Bars : Fe…

Aim- To Run the analysis and design the RCC Moment ResistingFrame. The ETABS file for a G+4 building is provided. Introduction- The ETABS file for a G+4 building is provided. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span continuous…

Aim- To Run the analysis and design the RCC Moment ResistingFrame. The ETABS file for a G+4 building is provided. Introduction- The ETABS file for a G+4 building is provided. The following challenge deals specifically with two columns at following grid intersection         1) 3A …

Aim- To Run the analysis and design the RCC shear walls.   Introduction-The etabs file for a G+6 building is provided. The challenge deals specifically with the shear wall of size 300x1500 at grid A-11 in                          the structural…