Aim: To create a MATLAB program for the forward kinematics of a 2R Robotic Arm, along with their repercussions in video form.   Objective: The main objective is to know the position (workspace) of manipulator by varying theta value & Animation.  Governing Equations: Body of Content:  Matlab Program-…

Aim: To solve second order ODE using MATLAB Programming   Objective: To write a program that solves the following ODE. This ODE represents the equation of motion of a simple pendulum with damping. To create Animation of Pendulum. EQUATIONS USED:   Where as, g = gravity in m/s2, L = length of the pendulum in m,…

Aim: To optimize the staglagmite function using genetic algorithm techniques using MATLAB The following ideas must first be understood in order to develop the genetic algorithm: 1.) What is a genetic algorithm? 2.) How genetic algorithm work using syntax.   Genetic algorithm: The genetic algorithm is a method…

AIM: To analyse/ parse a NASA thermodynamic data file, extract the coefficients and other characteristics of each species, and compute the specific heat (Cp), entropy (S), and enthalpy for each (H). Plot the values of Cp, H, and S using the local temperatures, and use MATLAB to show the molecular weight of each species.…

Aim: To construct the Switch Bezel plastic component using the provided class A surface, as well as to produce the necessary Tooling axis and carry out a drafting analysis on the model. Objective: First, you will need to generate the requisite proper Tooling axis, and then you will execute the Draft analysis on the class…

  Week 8 - Challenge 1 - Base Bracket Design   AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Objective:…

Objective : The objective of this project is to create a Surface meshing on a Pressure valve with element type of tria and mesh the model with three different target lengths i.e., 1mm, 3 mm and 5 mm  by using ANSA. ANSA: The automotive industry makes extensive use of the computer-aided engineering…

AIM: For the given model, check for the geometrical errors to make appropriate volumes. Create and assign PIDs as shown in the video. Perform surface mesh with the given target lengths as per PIDs. Blade stage-1 = 1 mm Blade stage-2 = 1 mm Impeller = 2 mm Shaft rotor = 1 mm Turbo casing = 5 mm Compressor casing = 5 mm…

Aim: Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Objective: First, you will need to generate the…

AIM: To Create the Core and cavity blocks for the switch bezel component. DESCRIPTION: CREATING TOOLING AXIS - The Tooling Direction refers to the general path that a part is pulled in when it is being formed in a mould. Essentially, the mould is constructed using two distinct components that are joined together. One of…

Objective: To Identifying and cleaning up any and all topological defects present in the BMW M6 Car model that was provided. In order to develop a surface mesh. The goal is to build a wind tunnel around the BMW M6 car. ANSA: The automotive industry makes extensive use of the computer-aided engineering tool known as ANSA…

OBJECTIVE: To design a with Master Section. INTRODUCTION During the stages of the product life cycle known as feasibility check and concept validation, the development of master sections takes place. These are the common guides that are used for design requirements, and following the development of the concept design,…

AIM: To produce the Door Handle Component using the provided Class-A surface as the starting point. In order to fulfil the criteria of the draught angle, it is necessary to create the tooling axis for the Class-A Surface that has been provided. To do the Draft analysis on the model. 1. DEPLOYMENT OF THE TOOLING AXIS -…

AIM: To produce the Door Trim Component using the provided Class-A surface as the starting point. In order to fulfil the requirements of the drafting angle, it is necessary to create the Tooling axis for the Class-A Surface that has been provided. For the purpose of carrying out the Draft analysis on the model. To create…

AIM: Constructing a model by making use of the Class-A surface of the bumper that has been provided here. As an added bonus, draft analysis on a closed body can be created by generating a B surface and a C surface. DRAFT ANALYSIS Using the Draft Analysis command, you will be able to determine whether or not the component…

Objective: In the models that have been provided to us, we need to look for errors in the geometry and get rid of any surfaces that won't be used for surface wrapping. Following the completion of the geometry cleanup, we will combine all three models. After that, the surface wrap operation for the merged model is the last…

AIM:  To create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  To create the Heat Stakes and the locators…

Objective: Find and fix all the topological mistakes in the model of the Tesla Cyber Truck Car that has been provided. Creating a surface mesh is the goal. Develop a wind-tunnel-like scenario for the Tesla Cyber Truck. ANSA: The automotive industry makes extensive use of the computer-aided engineering tool known as ANSA…

Objective: In this test, We are going to talk about Ahmed's body and the significance of it. Explain why there is a negative pressure in the wake region, and provide a vector plot that shows the wake region in a way that is easily understood. Describe the significance of the point where the two paths diverge. In order…

Objective: With regard to this obstacle, In the upcoming sections, we will provide a concise explanation of when and why a CHT analysis is performed. On an exhaust port, we will perform a simulation of both the flow of fluid and the heat transfer to the solid, also known as a CHT analysis. Then, we will present the velocity…

Aim: An analysis of the Rayleigh Taylor wave simulation for different mesh sizes, its effects on CFD, and a comparison of simulations and analytical methods Define the Atwool Number and discuss its research and application in various scenarios. Introduction: The Rayleigh–Taylor instability is an instability of an…

Objective: In order to simulate a forced convection flow on a graphics card and investigate the conjugate heat transfer that occurs during the simulation, to carry out mesh independent research, and to evaluate and evaluate the results of these investigations. We are going to run simulations at three different speeds:…

Objective:  To conduct studies on the cyclone separator and determine the efficiency of the separation as well as the pressure drop. Conduct the study with velocities ranging from one meter per second to five meters per second and with particle sizes ranging from one micrometer to five micrometers. Compile the findings…

Aim: To do a parametric study on the flow in a gate valve so that the velocity contour, velocity vector, and flow coefficient can be seen and calculated for each case. We will do a parametric study starting with the valve open at 10 mm and gradually increasing the opening by 10 mm until the valve is open at 80 mm. Introduction:…

Problem related to BTMS is attached in PDF format

Question For this challenge, you have to perform the four simulations in the  Gearbox and then you have to compare the results among all the four cases. Part 1: 20% Immersion, Fluid - Engine oil. 30% Immersion, Fluid- Engine oil. 20% Immersion,Fluid-n-heptane (c7h16). 30% Immersion,Fluid-n-heptane (c7h16). Part 2:…

AIM: The goal is to approximate a second-order derivative at the fourth-order level by means of a central differencing scheme, a skewed right-sided difference, and a skewed left-sided difference, all generated by use of the Taylor table approach, and then to compare these approximations to the analytical derivative of…

AIM: The purpose of this MATLAB-based project is to use several iterative techniques, such as the Jacobi, Gauss-Seidel, and sequential over-relaxation methods, to solve the 2D heat conduction equation for steady state and transient states. Problem Definition: Pde provides a definition for the equation of heat conduction.…

Objective: To verify that there are no geometrical mistakes and to do midsurfacing using the proper midsurfacing procedures for the model that was given. Assign PID and thickness to each of the midsurfaces, and ensure that the mesh meets the quality standards for the elements that have been provided. ANSA: The automotive…

Objective : The objective of this project is to create a Surface meshing on a given Sheet Metal component.  ANSA: The automotive industry makes extensive use of the computer-aided engineering tool known as ANSA for finite element analysis and computational fluid dynamics (CFD) analysis. BETA CAE Systems is the…

Objective: To verify that there are no geometrical mistakes and to do midsurfacing using the proper midsurfacing procedures for the model that was given. Assign PID and thickness to each of the midsurfaces, and ensure that the mesh meets the quality standards for the elements that have been provided. ANSA: The automotive…

Objective : The objective of this project is to create a Surface meshing on a given component.  ANSA: The automotive industry makes extensive use of the computer-aided engineering tool known as ANSA for finite element analysis and computational fluid dynamics (CFD) analysis. BETA CAE Systems is the company…

Objective: To verify that there are no geometrical mistakes and to do midsurfacing using the proper midsurfacing procedures for the model that was given. Assign PID and thickness to each of the midsurfaces, and ensure that the mesh meets the quality standards for the elements that have been provided. ANSA: The automotive…