yutube link of output: https://www.youtube.com/watch?v=Ogs0XOVoBIM   simulate the forward kinematics of a 2R Robotic Arm   %simulation the forward kinematics of a 2R Robotic Arm close all clear all clc %lets assume lenghth of base arm L1 as 1meter L1=1; %lets assume lenghth of second arm L2 as 0.5meter…

Aim : solving second order ODEs to animate motion of simple pendulum. Introduction: Understandinng simplependulum- a simple pendulum is a mechanical device that oscilates to a fixed point.It consist of mass 'm' hanging by a string of length 'L' in which one end is attached to a fixed point 'o' as shown in fig.most important…

https://skill-lync.com/student-projects/creating-simple-pendulum-motion The challenged has been attached as project.please do check the above link leads to the challange on motion of simple pendulum. maincode % Solving second order ODEs close all clear all clc % few given parameters: %length of pendulum (L) in meter L=1;…

Week 4.1 - Genetic Algorithm AIM: To create a Genetic Algorithm with a given staligmite function. OBJECTIVES: Write a code in MATLAB to optimise the stalagmite function and find the global maxima of the function. Clearly expalin the concept of genetic algorithm in your own words and also explain the syntax for ga in…

Project 1 - Parsing NASA thermodynamic data Aim: Write a function that extracts the 14 co-efficients and calculates the enthalpy, entropy and specific heats for all the species in the data file Objective: Plot the Cp, Enthalpy and Entropy for the local temperature range Calculate the molecular weight of each species and display…

 Project 2 - Rankine cycle Simulator Aim:    Create a Rankine Cycle Simulator. Objective: Create a Rankine Cycle Simulator. code should calculate the state points of the Rankine Cycle based on user inputs.  Plot the corresponding T-s and h-s plots for the given set of inputs. Title and axes labels are…

Benchmarking Benchmarking is a process of measuring the performance of a company’s products, services, or processes against those of another business considered to be the best in the industry, aka “best in class.” The point of benchmarking is to identify internal opportunities for improvement. By studying…

UNDERBODY COATING What is underbody coating ?  As the name sugest the under body coating is a thick layer of protective coating (asphalt/latex based usually) that is applied to the undercararge to protect  from chipping and rust proofing. This is done after the paintjob or after the total assembly of the vehicle…

AIM:  Design Hood Outer Panel, Inner Panel and the necessary reinforcements by following the Master Section HOOD: hood is a combination of sheet metal work which is designed in such a way that it must look good, provide aerodynamics to car,reduse impact to person insidethe car or to the person the car is being hit…

 SECTION MODULUS: Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members. Other geometric properties used in design include area for tension and shear, radius of gyration for compression, and moment of inertia and polar moment of inertia for stiffness. …

Fender Design Challenge   INTRO: Fender is the American English term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road spray from being thrown into the air by the…

AIM: Calculate the Wheel Arch gap at required points and check whether the car passes the European standard.   FENDER: Fender is the American English term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks,…

Objective : To create a roof with proper roof structure and supports also satisfy heat distrotion and snow load criteria.   Introduction: A roof structure for a vehicle body includes a roof opening defined by a pair of spaced apart side rails, each having a flange extending inwardly and being vertically offset below the…

  OBJECTIVE :To create a backdoor assmbley with given backdoor panel. INTRO: Backdoor/Tailgate is a door or a combination of 2door that is used to secure the commodities of passengers in the rear of the vehicle. it also acts as a protection to rear end colission. Most commonly found are top mount ,side mount and botom…

Week 8 - Challenge 1 - Base Bracket Design AIM:  Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Procedure:…

 Week 8 - Challenge 2 - Switch Bezel Design Aim: Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take…

Week 8 - Challenge 3 - Coin Holder Design AIM: Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness…

Week 8 - Challenge 6 - Core & Cavity Design AIM: Create the Core and cavity blocks for the switch bezel . Switch bezel   #creation of core lets create a extraction of class a surface create boundry on class A Extrapolate the boundry trim to export  trim b with c section without solid with soild join create…

Week 9 - Attachment Feature Creation (Ribs & Screw Boss) - Challenge 1 Aim :  To create proper rib design as per the standard data   Create the Screw boss for the Drill Handle considering the design rules mentioned in the video.  General Guidelines for Bosses:   Draft  - 0.5 degrees on…

 Week 8 - Challenge 4 - Bumper   Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of…

Week 8 - Challenge 5 - Door Trim Lower Create the Door Trim Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness of…

 Week 9 - Attachment Feature Creation - Challenge 2 Aim Create the Dog House for the Door Trim considering the design rules mentioned in the video. Consider the thickness of the part to be 2.5 mm. "C" is where the doghouse contacts the backside of the surface conditions:  Doghouse wall thickness…

 Week 9 - Project 1 - Door Trim Lower with Engineering Features Aim : with refernce to below given image, produce a ed model withs stakes and dog house and locators Use the given points in the model to create the locators and Heat stakes Refer to the below-given image for more details Given A-surface Check for any…

Week 9 - Project - A pillar Design with Master Section Aim : Creation of solid body with given A surface, creation of doghouse and locator  Use closed body command to create the solids Given Data:   check for boundry conditions Tooling Axis lets create main tooling axis with respect to matersesection…

Week 10- Assembly Workbench   Aim:   To create 2 assemblies according to the content covered in the course videos.  Provided with 2D diagrams of the components, create the individual part files and then create a complete assembly of those part files in the assembly workbench. After creating the…

Week 11 - Final project   AIM: Development of a Door Trim panel Creation of CAD model considering following inputs as like in OEM and tier1 companies a) Class A surface b) Nominal thickness : Refer master sections c) Attachment strategy :  Find a attachment strategy for the door panel complete work. Use…

 Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge AIM: Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip.   Provided link part…

Wiring harness routing & packaging Rules Week 3 Challenge   Question 1: Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Solution: Given cad data   Create center points on entry and exit section of p clip . wrt the…

Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge   Question: Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors.…

Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge   Question: Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use the connectors provided. After completion of routing, Check the bundle Continuity. Add snap of result in submission Add…

Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge   Question: Flatten the harness assembly completed in “ week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view. Solution: As per the quiestion let us import…

Project 1 AIM  To create harness for enging assy, with proper routing and protection.   Engine wiring harness: is an organized set of wires, cables, connectors and terminals that controls a vehicle’s electrical system. Engine wire harnesses relay electrical power and control information to outlying…

Project 2 Aim: Route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design. Apply Protection coverings as required.   Wiring harness A wiring harness is a group of wires bundled…

Week 14 challenge Add all requird parts to an assy file mate all components     Final assy after maiting   DRAWING Adding diamentions and tolerance   complete assy file is been attached

Modeling and Photo Realistic Rendering of Amarican Chopper OBJECTIVE: To create parts of an amarican chopper and assemble them Also create a realistic render of the same. Inturn getting an idea of all the different methods of approching a design solution, and also idea and methods to approach to get a realestic 3d.  …

Radar Mast & Final Assembly of Yacht  1. Radar Mast    create a new part , insert the surface from the the superstucture to get the base for mast with help of top blueprint creare a sketch and extrude it add all fillets create a sketch and revolve and add fillets create circles and extrud them with respect to blue print…

Advanced Sheet Metal Design Using NX Cad Challenge_2_Box Assembly Objective: To Create a Sheet metal box Introduction Sheet Metal Fabrication is the process of forming parts from a metal sheet by punching, cutting, stamping, and bending. 3D CAD files are converted into machine code, which controls a machine to precisely…