1. Aim:-   To determine the Mix proportioning of concrete for M30 grade of concrete using flyash and without using Flyash as a part of replacement of OPC Introduction:- Concrete mix design involves a process of preparation in which mix ingredients creates the required strength and durability for the concrete…

Aim:- To sketch a G+1 residential floor building as per vaastu and names of the structural drawings we are provided. Introduction:- In a G+1 residential building, Requirements for preparing strcutural drawings are listed below: Floor Plan drawing. Centre line drawing Plinth Beam layout drawing. Column Layout drawing. Column…

To design the above mentioned P-1 and P-2 drawings using coordinate system methods.  Introduction:- There are 2 types of coordinate systems.  1. Absolute Coordinate system:- Absolute coordinate system is whenever we mention any point with respect to the origin 0,0.  2. Relative coordinate system:- Relative…

Aim: To design the given drawings given in the attachement.  Introduction: The given drawings in the attachement are designed using commands in the Autocad.  Procedure:  A. Procedure for C.S. of Load Bearing wall over spread Footing:- First we have to take the dimension from any part of the drawing.  Let's take first point…

Aim: To design the given drawings in the attachment using commands in Autocad. Introduction: By using Autocad software, we have to design the drawings given in the attachment. Procedure: There are some drawings given in the attachment and the procedure for the drawings are listed below.  1. Procedure for the first…

1. Residence Plan:- Aim:- To sketch the residential building as shown in the attachment by using Autocad software.  Introduction: The given drawings in the attachement are designed using commands in the Autocad. Procedure: To start the drawing, first we have to set the limits by choosing Units and have to set the…

1.Create a column schedule Aim: To create a column schedule as shown in the figure.  Introduction: To create a column schedule in Autocad by using Lines, Text, Dtext or Single line text.  Procedure:  First we need to adjust text size and font name as given in the question.  First we need to understand…

1. Aim: To draw the elevation and details of a wardrobe.  Introduction: To draw the elevation and details of a wardrobe and sketching with provided dimensions and text with use of layers.  Procedure:  First we need to set the dimension to mm which is given in the drawing.  Then understand the drawing…

1. Aim: To design the plan and section as in the given attachment.  Introduction: To design the plan and section by using proper dimension techniques and dimension styles to document the project.  Procedure:  First before drawing we need to set the units as per the drawing requirement.  Then also we…

1. Aim: To design the residential building.  Introduction: To design and draft the residential building with the given dimensions for Architectural drawings and Structural drawings. Procedure: First before drawing we need to set the units as per the drawing requirement.  Then also we need to set limits by entering…

1. Aim: To create the template for the title block.  Introduction: To create the title block template as per industry standards or by assuming as per the size of paper.  Procedure:  First we need to set dimensions by using Units command and limmax.  Then take the line command and have to draw the lines…

1.  Aim: To design Kitchen layout with proper dimension techniques to dimension the kitchen layout.  Introduction: To design Kitchen layout with proper dimension techniques and to hatch the kitchen layout by assuming some dimensions.  Procedure:  First we need to set the dimension to mm which…

1. Aim: To create the layout of the plan and section given in the attachment.  Introduction: To create the layout of the plan and section which is given in the challenge-7 using template and mArch.dwt in Autoca.  Procedure: First we need to set the layout page in which we are going to set the drawing.  Then…

1. Aim: To create the 3D furniture element. Introduction: To create the 3d furniture element as in the given figure.  Procedure:  First we have to set the limits for 3d drawing by using un command.  And also have to set the limits by using limmax command.  Then the drawing space area has to change to…

1. Aim: To create a 3D Isometric view of the building with plan and elevation given. Introduction: To create a 3D Isometric view of the building with plan and elevation given in the figure.  Procedure: In the command prompt type limmax >100',100' In the command prompt type limits > 0',0' In the command…

Aim: To Create a 3 dimensional model of the residential building with a rendered view.  Intorduction: To Create a 3 dimensional model of the residential building with a rendered view using Autocad.  Procedure: In the command prompt type limmax >100',100' In the command prompt type limits > 0',0' In…

1. Aim: To create the new poroject and name the project appropriately. Introduction: To create the new project and name the project appropriately by using Revit.  Procedure:  First Open the revit software and is opened as below.  Then after opening the revit, then click on the icon button "New". From the…

1. Aim: To Define the BIM and summerizing the features of BIM and benefits of using BIM over 2D CAD tools.  Introduction: To Define the BIM and summerizing the features of BIM and benefits of using BIM over 2D CAD tools.  Procedure:  The Revit platform for the building information is design and documentation…

1. Aim: To create the project file created in week 2 by using floor tool under architecture tab by using proper material and thickness by using property browser.  Introduction:To create the project file created in week 2 by using floor tool under architecture tab by using proper material and thickness by using property…

1. Aim: To create a model ceiling for the first floor from architecture tab above the walls at first floor level.  Introduction: To create a model ceiling for the first floor from architecture tab above the walls at first floor level. Procedure: First we have to open revit software file for existing first floor…

1.  Building codes for modeling/efficiency of drawing in revit:- The National Building code is a document that provides guidelines for construction of structures like Residential, Institutional, Educational, Commercial, Assembly, and storage spaces.  It is important to follow these guidelines that are meant to…

1. Aim: To open and Architectural template using manage tab and set the project base point and project shared coordinates for the project.  Introduction: To open and Architectural template using manage tab and set the project base point and project shared coordinates for the project.  Procedure:  First…

1. Aim: To design the Multi story residential building.  Introduction: To design the Multi story residential building. Procedure:  Here i am choosing to design a residential building in Architectural and Structural model.  First we need to open the revit software and select for the Architectural template. …

1. Aim:- To explain about HVAC systems and the essentials in the modeling of buildings.  Introduction:- To explain about HVAC systems and the essentials in the modeling of buildings. Procedure:- HVAC stands for Heating, Ventilation and Air conditioning.  It is a technology of indoor environmental comfort.…

1. Aim:-  To create the topics discussed in class to complete the given tasks and list them by using shortcut keys in revit.  Introduction: To create the topics discussed in class to complete the given tasks and list them by using shortcut keys in revit. Procedure: Section Box:- BX (Shortcut Key) Open the…

1. Aim: To create a set of sinusoidal points and create a curve and create a surface out of the curve.  Introduction: To create a set of sinusoidal points and create a curve and create a surface out of the curve. Procedure: Open the revit software and open the architectural drawing template for creating dynamo. …

1. Aim: To Create the Architecture /Structure project file developed  in week6 to 8 and export the Revit architecture and structure mdel to Navisworks cache file.  Introduction: To Create the Architecture /Structure project file developed  in week6 to 8 and export the Revit architecture and structure…

1. Aim: To explain about the mode of failure or damage of the beams in the given figure and are the damages are repairable.  Introduction: To explain about the mode of failure or damage of the beams in the given figure and are the damages are repairable.  Procedure:  A. Observations:  In the figure…

1. Aim: To differenciate about Static analysis and dynamic analysis with proper representing pictures.  Introduction: To differenciate about Static analysis and dynamic analysis with proper representing pictures. Procedure:  Dynamic analysis is the process of testing and evaluating a program - while software…

1. Aim: To solve a five storey structure with 5 translational Degree of freedom is as shown in figure with given mass 'm'.  Introduction: To solve a five storey structure with 5 translational Degree of freedom is as shown in figure with given mass 'm'. Procedure: Modal Property (L) = `(Phi_n)^T' `,m…

1. Aim: To comment on the layout of the framing plan concerning earthquake resistance in the two horizantal directions X or Y (dots are columns, lines depict beams.  Introduction: To comment on the layout of the framing plan concerning earthquake resistance in the two horizantal directions X or Y (dots are columns,…

1. Aim: To create by taking the three alternatives taking into an account the restraint of floor shrinkage, the lateral stiffness and the torsional one with respect to the vertical axis, the vertical reinforcement required for the same total flexural capacity at the base, the static eccentricity, the system redundancy,…

1. Aim: To model a 25 storey building on E-tabs with structural properties as in the given question.   Introduction: To model a 25 storey building on E-tabs with structural properties as in the given question.  Procedure:   Open the Etabs software and select the New model option.   …

Aim: To create the influencing of Dynamic charecteristics, Natural period and Mode shapes of a building.  Introduction: To create the influencing of Dynamic charecteristics, Natural period and Mode shapes of a building. Procedure:  Model-A Open the Etabs software and click on the New Model.    …

Aim: To create a ETABS file for a G+4 buidling which is provided in the question and do run analysis and design the RCC moment resisting frame.  Introduction: To create a ETABS file for a G+4 buidling which is provided in the question and do run analysis and design the RCC moment resisting frame.  Procedure:…

Aim: To create for ETabs file for G+4 building which is provided in the question and to run the analysis and design the RCC moment resisting frame.  Introduction: To create for ETabs file for G+4 building which is provided in the question and to run the analysis and design the RCC moment resisting frame. …

Aim: To create a G+6 building is provided and to run analysis and design the RCC shear walls as shown in the given attachment.  Introduction: To create a G+6 building is provided and to run analysis and design the RCC shear walls as shown in the given attachment.  Procedure:  Open the drawing which…

Aim;

Aim: To design a square footing for a column size of 400 X 400. and to provide the sketch showing the size of the footing, maximum and minimum depth of the section, flexural reinforcement in both directions and anchorage of column steel.  Introduction: To design a square footing for a column size of 400 X 400.…