Vehicle dynamics projects for mechanical engineers

14 vehicle dynamics and suspension projects that Skill-Lync learners have actually done, 397 public reports in all: road loads and a BAJA ATV in Simulink, tyre, ride, understeer, anti-roll bar and anti-squat problems in MATLAB, then roll centre, ride, steering, compliance and pitch targets met in ADAMS Car. Each has the real inputs, worked answers to check yours against, and a way to take it further.

As of 21 Nov 2026: 397 of 1,41,067 public learner reports match one of these ideas · Counts are reports, not unique students

How to pick one

  1. Work the numbers by hand before you open a tool. The suspension course makes you find the roll centre from four hardpoints with a ruler or a spreadsheet before it lets you into ADAMS. Do the same with every project: a hand answer for ride frequency, understeer gradient or roll gradient is how you catch a wrong unit in the model, and several reports here show exactly that kind of slip.
  2. Chase a target, not a plot. Vehicle dynamics work in industry starts from targets: a ride frequency, a roll gradient in deg/g, a pitch gradient, a bump steer in deg/m. The strongest reports state the target, move a hardpoint, a spring or a bushing, and show how close they got. That is what an interviewer at an OEM or a Formula Student team will ask about.
  3. Keep one car through the whole set. The problem sets use different cars, so the numbers do not connect. Pick one vehicle (your BAJA or FSAE car, or a production car with published data) and run it through tyres, ride, roll, pitch and handling. One consistent car makes a far better portfolio than seven unrelated answers.

Road loads and a whole vehicle

Start at the vehicle level: the forces a motor has to beat, then a full BAJA ATV in Simulink.

Forces on a vehicle: motor speed from a tyre code and a propulsion-power calculator

BeginnerExcel27 reports

Week 1 of an EV course. Find the motor speed of an electric scooter that runs at 90 km/h through a fixed gear ratio of 7 on a 90/100 R10 tyre, then again on a 90/90 R18. Build an Excel calculator for propulsion power from kerb weight, payload, rolling resistance, air density, frontal width and height, drag coefficient, acceleration time, hill angle and speed, and say what it leaves out. Then: a 15% drop in tyre pressure doubles rolling resistance, so how much more power does the scooter need? The last question reads gradeability and average speed off the Range Rover Sport Dragon Challenge video.

Make it a final-year project: Take one real scooter's published kerb weight, top speed and motor power, and check whether your calculator says it can hold that top speed on the flat and climb a 10° slope.

Learn it in Introduction to Hybrid Electric Vehicle using MATLAB and Simulink

BAJA ATV with a CVT: a system-level Simulink and Simscape model

IntermediateSimulink, Simscape75 reports

Start from the MathWorks File Exchange BAJA all-terrain vehicle model (engine, variable-ratio CVT, simple gear, vehicle body, double-shoe brakes, Magic Formula tyres) and run it four ways: brake, throttle and CVT ratio from a Signal Builder; a dashboard of knobs and gauges; the CVT ratio from a lookup table on vehicle speed; and the lookup table with the dashboard. A common input is throttle 0.3 for 20 seconds, then full throttle with no brake. Plot vehicle speed, engine and CVT speeds and distance, and write it up as a technical report. Reports reach about 55 km/h at full throttle.

Make it a final-year project: Replace the lookup table with a flyweight-and-spring CVT model tuned to your team's engine, and check the 0-30 m time and top speed against a track test.

Learn it in Introduction to Physical Modeling using Simscape

Tyres, ride and handling in MATLAB

The classic vehicle dynamics problem sets, from tyre forces to understeer, roll and pitch.

Tyre force models in MATLAB: Pacejka Magic Formula and the brush model

IntermediateMATLAB or Octave22 reports

Two problem sets. Pacejka combined slip: with By 0.27, Cy 1.2, Dy 2900, Ey -1.6 and Bx 25, Cx 1.15, Dx 3200, Ex -0.4 (peak slip ratio 0.09, peak slip angle 4°), plot Fx and Fy against slip ratio at slip angles 0, 2, 4 and 6°, and against slip angle at slip ratios 0, 3, 6 and 9%. Brush model: at Fz 4000 N, μ 0.85, contact length 0.2 m, plot Fx against Fy for slip angles 2 to 10° as the slip ratio goes from 0 to 1 (the friction ellipse), then at Fz 3000 N and 3° find the effective cornering stiffness at slip ratios 0, 0.15 and 1.

Make it a final-year project: Fit the Magic Formula to a published tyre test (Mz or Fy against slip angle) and report the RMS error; one report fits Mz to under 2 N m.

Learn it in Vehicle Dynamics using MATLAB

Ride comfort: quarter car, half car and an ISO road profile

IntermediateMATLAB or Octave, Excel23 reports

A set of ride exercises. Quarter car: sprung weight 11.12 kN, unsprung 890 N, suspension spring 45.53 kN/m, tyre 525.35 kN/m, driven at 48 km/h over a road with a 9.15 m wavelength and 5 cm amplitude; find both natural frequencies and the body and wheel amplitudes. Half car: bounce and pitch frequencies and their oscillation centres. Classify a road from its power spectral density in ISO 8608 classes and rebuild a profile from it. Pick springs and anti-roll bars for a target ride frequency, roll gradient and pitch gradients.

Make it a final-year project: Add damping and plot body acceleration against frequency for three damper settings, then weight it by ISO 2631 to say which setting is most comfortable.

Learn it in Vehicle Dynamics using MATLAB

Steady-state handling: understeer gradient, characteristic speed and steering gains

IntermediateHand calculation, Excel or MATLAB11 reports

A car carries 1900 lb on the front axle and 1552 lb on the rear, on a 100.6 in wheelbase, with a table of tyre cornering stiffness against load (225 to 1350 lb). Find the Ackermann steer angle on 500, 200 and 50 ft radii, the understeer gradient, the characteristic speed, the lateral acceleration and yaw velocity gains at 60 mph, and the sideslip angle at the centre of gravity on an 800 ft turn at 60 mph. The last question asks why the understeer gradient comes out so low when cars usually sit around 3 to 4 deg/g.

Make it a final-year project: Add the missing understeer contributors (roll steer, lateral force compliance steer, aligning torque) as a budget and see how close you get to 3 deg/g.

Learn it in Vehicle Dynamics using MATLAB

Transient handling with a bicycle model: a road car against an F1 car

AdvancedMATLAB (state space)20 reports

Write the 2-DOF bicycle model in state space for two cars: a 907 kg front-wheel-drive car (yaw inertia 1128 kg m², wheelbase 2.539 m, CG 0.890 m behind the front axle) and a 780 kg F1 car (865 kg m², 2.902 m, CG 1.740 m behind the front axle). Find the undamped natural frequency, damping ratio, damped frequency and rise time, plot the step response of lateral speed, lateral acceleration and yaw rate, the response to a 5°, 7 Hz sine steer, and the yaw gain against frequency, then compare the steady-state yaw gain across the methods.

Make it a final-year project: Add a four-wheel-steer term (rear steer proportional to front) and find the ratio that makes sideslip zero at 100 km/h.

Learn it in Vehicle Dynamics using MATLAB

Anti-squat, anti-lift and pitch gradient: tune the instant centres for zero pitch

IntermediateExcel23 reports

A 3750 lb car with 55% on the front, its front side-view instant centre 13.22 in high and 28.5 in from the axle and the rear one 16 in high and 42.5 in away. Under acceleration, find the load transfer, front and rear deflections, the pitch angle and pitch gradient, the swing-arm angle for 100% anti, and the front anti-lift and rear anti-squat percentages. Then keep the rear swing arm 16 in above the contact patch, move the instant centre until pitch is zero, and prove it. Reports agree on 0.63 in front and 0.49 in rear deflection, about 1.3 deg/g and 61% anti-squat.

Make it a final-year project: Repeat it for braking (anti-dive and anti-lift) and plot pitch gradient against anti percentage, with the brake-pedal feel trade-off in words.

Learn it in Vehicle Dynamics using MATLAB

Anti-roll bar sizing: roll gradient, load transfer and auxiliary roll stiffness

IntermediateExcel23 reports

From the car's weights, track, ride rates and tyre rates, find the roll moment, roll gradient, elastic load transfer and the front roll stiffness at wheel centre, then the anti-roll bar rate for one-wheel jounce and for roll, the bar's own stiffness and the auxiliary roll stiffness share, and size the bar from its outer and inner diameters and arm lengths. Reports agree on a roll gradient of about 3.18 deg/g, a bar rate of about 149 lb/in in one-wheel jounce and about 71% auxiliary roll stiffness at the front.

Make it a final-year project: Fix the roll gradient at a target (say 3.8 deg/g) and pick bar diameters front and rear for a front roll-stiffness share that gives a mild understeer balance.

Learn it in Vehicle Dynamics using MATLAB

Suspension design in ADAMS Car

From a roll centre worked by hand to steering, compliance and pitch targets met by moving hardpoints.

Roll centre from hardpoints: the front-view instant centre by hand

BeginnerExcel or hand calculation15 reports

The first suspension exercise: no Adams allowed. Given the upper and lower control arm points of a double wishbone in the front view (upper link from (105, 425) to (285, 460) mm, lower from (105, 185) to (370, 170) mm, contact patch at the origin), a 300 mm tyre radius and a 1600 mm track, find the instant centre and the roll centre height. Reports agree on an instant centre near (-851, 239) mm and a roll centre about 225 mm below the ground; one drawn by hand comes out 10 to 14 mm off.

Make it a final-year project: Move the upper inner point up and down in 10 mm steps and plot roll centre height against it, then check the trend in a kinematic tool.

Learn it in Suspension Design using ADAMS

Ride rate, a flat ride and damper settings: the three Vehicle Ride problems

BeginnerHand calculation or Excel68 reports

Three problem sets from the suspension course's ride week. Vehicle Ride: why wheel rate differs from spring rate and ride rate from wheel rate, why compression and rebound damping differ, why the rear ride frequency sits above the front, and a quarter car of a 2000 kg vehicle. Vehicle Ride 1: with a 2.7 m wheelbase at 60 mph and the front fixed at 1.15 Hz, find the rear frequency for a flat ride, then the springs for a 245 N/mm wheel rate at motion ratios of 0.97 front and 0.85 rear on a 1500 kg car with 60% on the front. Vehicle Ride 2: a 1900 kg car with 55% on the front, springs of 20 and 30 N/mm and tyres of 250 N/mm; find critical damping, initial damping at damping ratios of 0.7 for the body and 0.2 for the wheel, and the low and high speed compression and rebound coefficients with rebound three times compression.

Make it a final-year project: Turn the damping coefficients into a force-velocity curve with a knee at a chosen speed, and check the flat-ride frequencies at kerb, design and full load.

Read real reports

Learn it in Suspension Design using ADAMS

Steering geometry in ADAMS Car: caster, kingpin inclination and scrub radius

IntermediateADAMS Car36 reports

Run a parallel wheel travel analysis on the double-wishbone front suspension, read the six steering-axis numbers, then move hardpoints to reach the targets: caster about 4°, caster moment arm about 21 mm, kingpin inclination about 13°, steer-axis offset about 85 mm, longitudinal offset about 0 mm and scrub radius about 20 mm. The baseline sits near caster 5.4°, kingpin inclination 10.1° and a longitudinal offset of -18.7 mm. Reports move the outer ball joints fore-aft for caster and trail, and in-out for kingpin inclination and scrub, and argue whether the six can be set independently.

Make it a final-year project: Check steering effort and returnability at each step (the trail and scrub you chose change both), and note which target you would give up first.

Learn it in Suspension Design using ADAMS

Suspension compliance in ADAMS Car: brake steer, recession and bushing tuning

AdvancedADAMS Car17 reports

Load the rear multilink from the Adams Car library and run static loads to measure brake steer and traction steer (deg/m), wheel centre recession under traction and under braking (mm/kN), and lateral force compliance steer and camber (deg/kN), and say whether each is toe-in or toe-out and understeer or oversteer. Then move hardpoints for a bump steer of +2.6 deg/m, and change one bushing at a time for a recession stiffness of about 500 N/mm and a camber compliance of 0.45 deg/kN. Reports agree on 1 mm/kN of recession under traction and about half that under braking, because braking acts at the contact patch and traction at the wheel centre.

Make it a final-year project: Plot the trade-off between recession stiffness (ride harshness) and toe change under braking (stability) for five bushing rates, and pick one.

Learn it in Suspension Design using ADAMS

Pitch gradient targets in ADAMS Car: anti-dive and anti-squat from hardpoints

AdvancedADAMS Car, Excel13 reports

The course project: a double-wishbone front and a multilink rear with springs of 100 N/mm and 125 N/mm and motion ratios of 0.48 and 0.59. Move the side-view hardpoints until the acceleration pitch gradient reaches 2.25 deg/g and the braking pitch gradient 1.60 deg/g, using the anti-dive and anti-squat percentages Adams reports, and fill in the results sheet. One report lands within 0.6% of both targets.

Make it a final-year project: Show what the anti geometry costs: plot wheel caster change in bump and the brake-torque reaction for your final hardpoints.

Learn it in Suspension Design using ADAMS

Build and post-process a suspension in ADAMS Car

BeginnerADAMS Car24 reports

The Adams basics: create a suspension assembly from a template, run it, then post-process the results. Make plot templates with your own styles, titles and labels, export and re-import a plot configuration file and numeric data, and export an animation as a video. One report plots wheel longitudinal recession for the baseline, with the lower arm points raised 10 mm and with the upper arm points lowered 10 mm.

Make it a final-year project: Script a design of experiments over two hardpoints and plot bump steer as a response surface instead of changing points by hand.

Learn it in Suspension Design using ADAMS

Before you start

The reports never name their course. They share titles and question sheets, and the same learners did the ADAMS and MATLAB problem sets in sequence ('Problem set 2 - week 3', 'Week 11'), which points to the vehicle dynamics module of Skill-Lync's postgraduate programs. We link each idea to the standalone course whose syllabus covers it.

A challenge input is quoted only when at least two learners' reports carry it; numbers that appear in one report are marked 'one report'. A few reports here are word-for-word copies of earlier ones, and some theory sections read like text from the web, so we picked the examples by hand: learners' own work, the earlier report where two match.

These are learner submissions from 2018 to 2025 and several contain mistakes: degrees passed to tan(), an acceleration force without the mass, a sign slip in the quarter-car transmissibility, pitch gradient divided by ft/s² instead of g. Read them as examples of the work, not as answer keys, and check every number against a hand calculation.

Questions students ask

What are good vehicle dynamics projects for mechanical engineering students?

Start with ride (a quarter-car model and a flat-ride check), then steady-state handling (understeer gradient and characteristic speed), a tyre model (Pacejka Magic Formula or the brush model), roll (anti-roll bar sizing to a roll gradient) and pitch (anti-squat and anti-dive). If you can get ADAMS Car, tune steering geometry and bushings to targets. The 14 projects on this page follow that order, and every one links to real reports.

How do you calculate ride frequency?

Ride frequency = (1/2π) × √(ride rate / sprung mass at that corner). The ride rate is the wheel rate and the tyre rate in series: Kr = Kw × Kt / (Kw + Kt), and the wheel rate is the spring rate times the motion ratio squared. In one Vehicle Ride report, a 500 kg corner with 25 N/mm at the wheel and a 250 N/mm tyre gives a ride rate of 22.7 N/mm and 1.07 Hz; the 50 kg wheel bounces at 11.8 Hz.

What rear ride frequency gives a flat ride?

The rear wheels hit a bump later than the front by wheelbase ÷ speed, so the rear must oscillate faster to catch up. In Vehicle Ride 1, a 2.7 m wheelbase at 60 mph (26.8 m/s) gives a 0.101 s lag. The front at 1.15 Hz has a 0.870 s period, so the rear needs 0.769 s, which is 1.30 Hz. That is why rear ride frequencies usually sit above the front.

How do you solve the quarter-car model problem?

With the sprung weight of 11.12 kN, unsprung 890 N, a 45.53 kN/m spring and a 525.35 kN/m tyre, the body mode is at 0.97 Hz and wheel hop at 12.63 Hz. At 48 km/h over a 9.15 m wavelength the road excites the car at 1.46 Hz. Solving the two undamped equations of motion at that frequency gives a body amplitude 0.80 times the road's (out of phase) and a wheel amplitude 0.87 times. One report's code gets 0.30 because of a sign slip in the denominator.

What is the understeer gradient and characteristic speed?

Understeer gradient K = Wf/Cαf − Wr/Cαr (deg/g), the front axle load over its cornering stiffness minus the same for the rear. In Problem Set-1b (1900 lb front, 1552 lb rear, 100.6 in wheelbase) the per-tyre stiffnesses are 232.1 and 195.2 lb/deg, so K = 0.118 deg/g and the characteristic speed √(57.3 L g / K) is 361 ft/s, about 246 mph. Real cars sit near 3 to 4 deg/g because suspension and steering compliance add understeer the tyre-only model leaves out.

Why do most reports get the sideslip angle in Problem Set-1b wrong?

Sideslip at the CG is β = 57.3 c/R − Wr V²/(Cαr g R), where Cαr is the cornering stiffness of the whole rear axle. Most reports read one tyre's stiffness at the full 1552 lb axle load (338.6 lb/deg) and get −1.05°. Two tyres at 776 lb each give 2 × 195.2 = 390.5 lb/deg, the same per-tyre values used for the understeer gradient, and β = −0.87° on the 800 ft turn at 60 mph. Tyre load sensitivity is why the two differ.

What is the Pacejka Magic Formula?

An empirical fit for tyre force against slip: y = D sin(C arctan(Bx − E(Bx − arctan Bx))). D is the peak force, C the shape factor, B the stiffness factor and E the curvature, and B × C × D is the slope at zero slip (the cornering or longitudinal stiffness). The problem set uses By 0.27, Cy 1.2, Dy 2900, Ey −1.6 for lateral force with slip angle in degrees. A common mistake in the brush-model problem is passing degrees to tan(), which gives a negative cornering stiffness.

How does a bicycle model compare a road car and an F1 car?

Using Problem Set-1c's data, the 907 kg road car at 100 km/h has a yaw natural frequency of 7.19 rad/s (1.14 Hz) with damping ratio 0.72, and a steady-state yaw gain of 5.4 per second. The 780 kg F1 car at 350 km/h has 13.3 rad/s and damping ratio 0.98, and a yaw gain of 29.7 per second: much stiffer tyres and more weight at the rear make it respond faster and settle without overshoot.

Which Skill-Lync courses are these projects from?

The tyre, ride, handling, roll and pitch problem sets match Vehicle Dynamics using MATLAB, whose recorded classes use GNU Octave, so you can practise without a MATLAB licence. The roll centre, Vehicle Ride, steering, compliance and pitch projects match Suspension Design using ADAMS. The road-load sheet is week 1 of Introduction to Hybrid Electric Vehicle using MATLAB and Simulink, and the BAJA ATV matches the all-terrain vehicle project of Introduction to Physical Modeling using Simscape. Many of these were done inside Skill-Lync's postgraduate programs.

Turn a project into a job-ready portfolio

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.