Baja SAE ATV design calculator

The powertrain and brake numbers a Baja SAE or mBAJA design report needs: CVT top speed, launch force, wheelspin, gradeability and a 100 ft acceleration run, then line pressure, brake force, which axle locks first, the pedal force that locks all four wheels and the stopping distance. Free, no sign-up, runs in your browser.

2026 engine rules · load transfer included · checked by a separate solver · Updated 19 Nov 2026

Vehicle
Engine and CVT
Brakes

Engine figures are the rulebook / catalogue values (stock engine, so an upper bound). Everything else in the presets is a typical Baja value assumed by Skill-Lync, not any team's car. Pistons per side: 1 for a single-piston floating caliper or a 2-piston opposed caliper.

Powertrain

Top speed59.4 km/hlimited by the governor
100 ft (30.5 m) run3.79 sexit 47.7 km/h
    Force at the driven wheels against speed for the CVT powertrain, with the tyre grip limit and the level-road resistance0.00.51.01.52.02.53.0010203040506070Speed (km/h)Force at the wheels (kN)governor 59 km/h
    Blue: force the engine can put through the CVT (peak torque in the low ratio, then rated power as the CVT upshifts, cut at the governed speed). Green: what the driven tyres can pass. Dashed: level-road resistance. Where blue is above green, the tyres spin.

    Brakes

    Deceleration at the pedal force0.54 gstops from top speed in 25.6 m
    Pedal force to lock all four408 Nrear axle locks first
      FrontRear
      Ideal braking diagram: rear against front brake force as a fraction of vehicle weight, with the ideal curve, the front and rear lock lines at mu 0.7 and the installed brake balance00.10.20.300.10.20.30.40.50.60.7Front brake force ÷ weightRear brake force ÷ weight0.7 g
      Ideal braking diagram. The ideal curve is where both axles reach the grip limit together. Pressing the pedal moves the car out along the installed line (dot: your pedal force). If the line meets the rear-lock line first, the rear wheels lock first.

      What does a Baja SAE design calculation include?

      A Baja SAE design report has to show that the car is fast enough, stops, steers and survives. The powertrain sums give the overall reduction, top speed, launch force and gradeability. The brake sums give line pressure, brake force per axle, which wheels lock first and the stopping distance. Steering, suspension and roll-cage FEA complete it. This calculator does the first two together, because they share the same inputs: mass, wheelbase, CG height, weight split, tyre radius and grip.

      The steering and suspension parts have their own tools: the Ackermann steering calculator (turning circle, Ackermann %) and the ride frequency calculator (spring rate, motion ratio, damping).

      Which engine do Baja SAE and BAJA SAEINDIA use in 2026?

      All Baja cars in a series run the same engine, so the powertrain design is about the CVT, the gearbox and the tyres. As of the 2026 BAJA SAEINDIA rulebook (Rev01, 6 November 2025), mBAJA teams use a Honda GX430T QX; Baja SAE in North America runs a Kohler CH440 with a restriction plate. Both governors are capped at 3,800 rpm, and the US rules disqualify any attempt to defeat the governor.

      SeriesEngineSizePowerTorqueGovernorSource
      BAJA SAEINDIA 2026 (mBAJA)Honda GX430T QX425 cc9.6 kW (12.87 HP) at 3,600 rpm27.7 N·m at 2,500 rpm3,800 rpm or lowerRulebook 2026 Rev01 B.2.2, B.2.8.8
      Baja SAE 2025 (US, Canada)Kohler CH440 + Baja SAE restriction plate429 cc10.4 kW (14 hp) at 3,600 rpm, stock, gross30.8 N·m at 2,800 rpm, stock, gross3,750-3,800 rpmRules 2025 Rev C B.2.1, B.2.7.9; Kohler catalogue
      BAJA SAEINDIA 2025Briggs & Stratton 10 HP Vanguard Model 19 (19L232-0054-G1)---3,800 rpmRulebook 2025 Rev00 B.2.7

      The figures are catalogue values for a stock engine: Kohler notes that real output is lower than its gross rating, and the US restriction plate takes more off. Treat them as upper bounds. The rules also fix the width at 162 cm (64 in) at the widest point and leave length free, though tracks are laid out for cars up to 274 cm (108 in).

      How do you calculate the top speed of a Baja with a CVT?

      On a Baja the governor, not air drag, almost always sets top speed. When the CVT reaches its high ratio and the engine reaches its governed speed, the car can go no faster:

      Those are the mBAJA preset's numbers: the GX430T at 3,800 rpm, a 0.9 CVT high ratio, a 7.5:1 gearbox and a 23-inch tyre with a 0.28 m loaded radius. Below that speed the CVT keeps the engine near its best output. At launch it sits in its low ratio with the engine near peak torque. As the car speeds up it upshifts and holds the engine near rated power:

      That is more than the car weighs (2,453 N), so on paper this car could climb a wall. The tyres can't pass it. With rear drive, accelerating moves load onto the rear axle, which raises the grip limit:

      So the preset spins its rear tyres from rest until the force drops to 1,413 N, at about 20.8 km/h. In a straight 100 ft (30.5 m) run it takes 3.79 s and leaves at 47.7 km/h. A shorter CVT low ratio would not make it quicker; more weight on the rear axle or a grippier tyre would.

      How steep a hill can a Baja climb?

      With an overall reduction of about 30:1 in the CVT low ratio, grip sets the limit on a hill, not the engine. Climbing slowly, the rear axle carries wr cos θ of the weight plus a share (h/L) sin θ shifted back by the slope. Setting the grip on the rear tyres equal to the grade and rolling resistance gives a closed form:

      The four-wheel-drive preset climbs 66.0% because all of its weight is on driven wheels (tan θ = μ − Crr). In practice the hill-climb event is decided by loose soil, rocks and lifting front wheels, so treat these figures as upper limits.

      How do you calculate Baja brake line pressure and braking force?

      Baja rules (B.7.1) ask for a hydraulic system on all wheels, worked by one foot pedal, with at least two independent circuits. Most cars use two master cylinders on a balance bar, one for the front calipers and one for the rear. The driver's foot force is multiplied by the pedal ratio PR and split by the balance bar share s. Each caliper then clamps the rotor from both sides, so friction acts on two faces:

      Apiston is the piston area on one side of the rotor, reff the effective rotor radius (roughly the middle of the pad) and rtyre the loaded tyre radius. The preset's single inboard rear rotor gives 484 N at the rear tyres at the same 26.3 bar.

      Which wheels lock first, and what pedal force locks all four?

      Braking shifts load from the rear axle to the front, by mDh/L, where a and b are the distances from the front and rear axles to the CG:

      An axle locks when its brake force reaches μ times its load. Both lock together only if the brake force is split in proportion to the axle loads at a deceleration of μg:

      With the balance bar centred, the mBAJA preset sends less than the ideal share to the front, so its rear wheels lock first, at 366 N on the pedal. A car with locked rear wheels and rolling fronts can swap ends. All four lock only at 408 N:

      kf and kr are the front and rear brake forces per newton of pedal force. At the preset's 300 N design push the car does not lock any wheel, and it stops at 0.54 g. The second preset fixes both problems with parts: the balance bar moved to 55% front and 5/8-inch master cylinders instead of 3/4-inch. Now the fronts lock first, at 255 N, and all four lock at 270 N, under the 300 N design push. A smaller master cylinder raises pressure for the same push and needs more pedal travel, so check the travel too.

      The 2026 BAJA SAEINDIA rulebook asks the pedal itself to survive 2,000 N; that is a strength load case, not the force a driver can hold. Design the lock-up force well below what your driver can push repeatedly.

      How far does a Baja take to stop?

      Once all four wheels lock, the tyres can't give more than μ times the weight, so the shortest stop is:

      The Skill-Lync student report Design calculations of Baja SAE ATV uses 16.7 m/s and μ = 0.7. Its deceleration (6.867 m/s²) is right, but its stopping distance of 13.78 m is an arithmetic slip:

      The same report's pedal-force case finds a deceleration of 15.1 m/s², which a tyre with μ = 0.7 cannot deliver: no stop can beat μg, whatever the brakes. The India dynamic test asks for a stop with all four wheels locked within 8 m (26 ft) after reaching at least 40 km/h (rule F.2.5). At exactly 40 km/h, sliding to rest in 8 m takes an average friction of:

      On μ = 0.7 the slide is 9.0 m. A car that brakes at the 40 km/h minimum on dry, hard ground passes; on loose dirt it relies on the tyres ploughing into the surface. The calculator shows both distances.

      What this calculator does not cover

      • The real CVT and engine curves. The engine runs at peak torque, then at rated power, with no losses in the shift. Real CVT tuning (engagement and shift rpm, belt slip) changes the launch.
      • Rotating inertia. The wheels, CVT sheaves and engine add effective mass, so the real acceleration run is a few per cent slower.
      • Sliding vs peak grip. One μ is used for driving, braking and locked tyres. On dirt, locked tyres can plough and stop shorter; on hard ground they slide at less than peak grip.
      • Brake hardware effects. Pad friction falls when hot, calipers need a little pressure before the pads touch, and master cylinder travel, hose swell and pedal stiffness are not modelled.
      • Steering, suspension and the roll cage. Use the steering and ride tools for the first two and FEA for the frame (the rules set the tube sizes and the load cases you check).
      From hand calcs to a full vehicle model

      Skill-Lync's vehicle dynamics course takes this force balance into MATLAB: tyre models, braking, steering and ride, the work chassis and vehicle-dynamics teams hire for.

      Frequently asked questions

      What calculations are needed for a Baja SAE ATV?

      A Baja design report usually covers the powertrain (overall CVT and gearbox reduction, top speed, launch force, gradeability), the brakes (pedal ratio, master cylinder and caliper sizes, line pressure, brake force, which axle locks first, stopping distance), steering geometry (Ackermann, turning radius), suspension (spring rate, ride frequency) and roll cage strength (FEA on the frame).

      What engine does BAJA SAEINDIA use in 2026?

      The BAJA SAEINDIA 2026 rulebook (Rev01, 6 Nov 2025) specifies the Honda GX430T QX for mBAJA: 425 cc, 9.6 kW (12.87 HP) at 3,600 rpm and 27.7 N·m at 2,500 rpm, with the governor set to 3,800 rpm or lower. The 2025 season used the Briggs & Stratton 10 HP Vanguard Model 19. Baja SAE in the US runs the Kohler CH440.

      What is the top speed of a Baja SAE car?

      Most Baja cars are limited by the engine governor, not by drag. Top speed = governed engine speed × 2π/60 × tyre radius ÷ (CVT high ratio × gearbox reduction). With 3,800 rpm, a 0.28 m tyre radius, a 0.9 CVT high ratio and 7.5:1 reduction that is 59.4 km/h.

      How do you calculate the stopping distance of a Baja ATV?

      If all four wheels lock, the deceleration is at most μg, so the stopping distance is v² ÷ (2μg). From 16.7 m/s on μ = 0.7 that is 20.3 m. Below the lock-up pedal force the deceleration is the total brake force ÷ mass, which gives a longer stop.

      Why must a Baja lock all four wheels?

      Both the Baja SAE and BAJA SAEINDIA rules (B.7.1) require a hydraulic brake system on all wheels, worked by one foot pedal, with at least two independent circuits, that can lock and slide all wheels when stationary and at speed. Scrutineers test it dynamically: in India, from at least 40 km/h with a stop on four locked wheels.

      Should the front or rear wheels lock first?

      Front first. If the rear axle locks first, the rear of the car loses its side grip and the car can spin. Front lock-up only costs steering, which the driver gets back by easing off the pedal. Set the balance bar so that the installed front share of brake force is a little above the ideal (b + μh)/L.

      Is this calculator accurate?

      For the models it uses, yes. Skill-Lync re-solved the two presets and 60 random cars in a separate Python script (bisection on the axle force balance, quadrature in speed for the acceleration run), and this page's code agrees to within 1e-5. The answers are only as good as your inputs, especially μ, CG height and efficiency.

      Related on Skill-Lync

      Sources

      • SAEINDIA, BAJA SAEINDIA Rulebook 2026, Rev01 (6 Nov 2025): B.1.6 dimensions, B.2.1-B.2.2 Honda GX430T QX, B.2.8.8 governor, B.7.1 brakes, F.2.5 dynamic brake test. Previous engine: Rulebook 2025 Rev00 B.2.7.
      • SAE International, Baja SAE Rules 2025 Rev C (5 May 2025; copy hosted by SAE Mexico): B.1.6, B.2.1, B.2.7.9 governor, B.7.1 brakes, C.2.2.3 brake test. Rules read 19 Nov 2026.
      • Kohler, Command PRO 6-14 HP catalogue (E-2141-D): CH440 429 cc, 14 hp at 3,600 rpm, 30.8 N·m at 2,800 rpm, gross.
      • T. D. Gillespie, Fundamentals of Vehicle Dynamics, SAE, ch. 2-3 (tractive effort, load transfer, braking); R. Limpert, Brake Design and Safety, SAE, ch. 7 (ideal braking, lock sequence).
      • Worked examples and all their numbers: Skill-Lync, checked by scripts/verify/baja.py, which finds the lock points by bisection on the axle force balance and the acceleration run by quadrature in speed, and is cross-checked against this page's calculator code at build time.
      Free counselling

      Turn your Baja experience into a chassis job.

      Vehicle dynamics and chassis teams hire engineers who can model braking, ride and handling in MATLAB, not just fill in a design report. A Skill-Lync counsellor can map the course that fits the role you want.

      Talk to a vehicle dynamics course counsellor

      Free. We call you back, usually the same day.

      By submitting you agree to our Terms and Privacy Policy.

      Talk to a career counsellor

      Talk to a career counsellor

      Free 20-minute call. We'll map the right course to where you want to work.

      By submitting you agree to our Terms and Privacy Policy.