Ackermann steering calculator
Enter your rack-and-pinion steering linkage and get the inner and outer wheel angles across the whole lock, the Ackermann percentage at each angle, the turning radius, turns lock to lock, and the steering effort to park the car. Free, no sign-up, runs in your browser.
Top-view linkage solved exactly · parking effort from the tyre contact patch · checked by an independent solver · Updated 16 Nov 2026
Geometry (mm)
(arm lines meet at the rear-axle centre). β leans the arms inward; 0 = parallel arms.
Effort (parking, no power assist)
What is Ackermann steering geometry?
When a car turns slowly, each wheel should roll along its own circle around one shared turn centre, which sits on the line of the rear axle. The inner front wheel is closer to that centre, so it must steer more than the outer one. Ackermann geometry is the condition that makes both front wheels point at the same centre:
Here δi and δo are the inner and outer wheel angles, t is the distance between the two steering axes where they meet the ground (the kingpin track, a little less than the wheel track) and L is the wheelbase. Get it wrong and one tyre scrubs sideways in tight turns: you hear it in a car park and see it as shoulder wear.
Real linkages only approximate it, so engineers quote how much of the ideal toe-out they achieve:
100% is true Ackermann, 0% is parallel steer (both wheels at the same angle), and below 0 is anti-Ackermann, which some racing cars use because at high lateral acceleration the more heavily loaded outer tyre works at a larger slip angle.
Worked example: a hatchback-size rack-and-pinion linkage
Wheelbase 2450 mm, kingpin track 1300 mm, steering arms 130 mm long, rack 130 mm behind the axle line with its inner joints 760 mm apart, 65 mm of rack travel to full lock. The arms are set by the classic rule of thumb, their lines meeting at the centre of the rear axle:
The tie rods come out 236.7 mm long. Solving the linkage at full lock gives an inner angle of 38.35° and an outer angle of 28.96°. Perfect Ackermann at that inner angle would need:
So at full lock this linkage is almost exactly Ackermann. At half lock (inner 15.9°, outer 14.5°) it gives only 70%: the percentage changes along the lock, which is why a single number without an angle means little.
The low-speed turning radius of the outer front wheel follows from the outer angle and the scrub radius rs (here 30 mm):
That is a 10.2 m turning circle at the outer front tyre. With 44 mm of rack travel per steering-wheel turn the wheel goes 2.95 turns lock to lock, an overall ratio of about 17.5:1 at half lock.
Does the rule of thumb give 100% Ackermann?
The rule of thumb, tan β = (t/2)/L, comes from the old single-tie-rod trapezoid. With a rack, where the rack sits matters as much as the arm angle. Move the same rack 130 mm ahead of the axle instead of behind it (arms pointing forward and outward along the same lines) and the full-lock Ackermann falls from 102% to 49%:
With the rack behind the axle, the arm angle has the biggest effect:
| Arm angle β | Inner angle at full lock | Outer angle | Ackermann at full lock |
|---|---|---|---|
| 0.0° | 30.3° | 29.7° | 9% |
| 5.0° | 31.7° | 29.3° | 36% |
| 10.0° | 34.0° | 29.0° | 66% |
| 14.9° (rule of thumb) | 38.4° | 29.0° | 102% |
| 18.0° | 46.5° | 29.0° | 140% |
Parallel arms (β = 0) still give 9% here, because the tie rods are not parallel to the rack; at β = 18.0° the linkage over-steers the inner wheel (140%, 46.5° inner) and is close to locking over centre. Practical steps: choose the lock you need, set β and the rack position, then check the Ackermann percentage across the lock range rather than at one angle.
How do you calculate steering effort?
The hardest job for the driver is turning the wheel with the car standing still, when each front tyre has to be twisted on the road. A simple model treats the contact patch as a circle of uniform pressure equal to the tyre pressure, so its area is Fz/p. Twisting a uniform-pressure disc about its centre takes a torque of two thirds of μFz times its radius, the same result as a flat clutch plate:
(The contact area here is 160 cm². If you have met the shortcut T = (μ/3)√(Fz³/p), it is the same formula with 0.333 in place of 2/(3√π) = 0.376, about 11% lower.) From the kingpin torque to the driver's hands:
Here h is the perpendicular distance from the kingpin to the tie rod's line (the arm's effective lever, which changes with lock), θ the tie rod's angle to the rack, c the rack travel per steering-wheel turn, η the gear efficiency and D the steering wheel diameter. At half lock in the example, the levers are 106 and 130 mm, the tie rods pull 1267 and 1035 N, the rack needs 2298 N, the steering wheel 18.9 N·m (η = 85%) and the rim force is 100 N on a 380 mm wheel.
For comparison, UN Regulation No. 79 caps the effort for an M1 passenger car at 150 N in its driving test (onto a 12 m radius within 4 s), not at standstill. A parking effort near 100 N is heavy; wide tyres and quick racks raise it further, which is why most cars now have power steering. A slower rack (smaller c) cuts the effort in proportion but adds turns lock to lock.
What this calculator does not cover
- 3D geometry. It solves the linkage in the top view. Caster, kingpin inclination, camber and tie-rod height differences (which also cause bump steer) change the angles slightly; check them in a 3D kinematics tool such as ADAMS/Car, Lotus Shark or a CAD sketch.
- Slip angles. Ackermann is a low-speed idea. At speed both front tyres run slip angles that depend on their loads, so the best Ackermann for handling is a tuning choice, not a formula.
- Real parking torque. The disc model ignores the tyre's own twist stiffness, scrub radius (the tyre rolls around the kingpin as well as twisting), caster and kingpin-inclination jacking, ball-joint friction and road surface. Use it to compare designs and size a rack; measure the real car.
- Efficiency. η is an input: rack-and-pinion gears are efficient, but seals, joints and the column add friction, and power assistance changes everything.
- Rack travel and stops. Set the rack travel to your rack's real stop; the calculator flags a linkage that would lock over centre.
Skill-Lync's vehicle dynamics courses go from these hand calculations to full multibody models of suspension and steering, the work chassis teams hire for.
Frequently asked questions
What is the Ackermann steering formula?
For the wheels to roll around one turn centre at low speed, the outer and inner front wheel angles must satisfy cot δo − cot δi = t/L, where t is the distance between the steering axes (kingpins) and L is the wheelbase. For a 2450 mm wheelbase and 1300 mm kingpin track, an inner angle of 38.4° needs an outer angle of 29.1°.
How do you calculate Ackermann percentage?
Ackermann % = (δi − δo) / (δi − δo,ideal) × 100: the toe-out your linkage actually produces at a given inner wheel angle, as a share of the toe-out perfect Ackermann would produce. 100% is true Ackermann, 0% is parallel steer (both wheels at the same angle) and a negative value is anti-Ackermann. It changes with steering lock, so always quote the angle it was measured at.
Does pointing the steering arms at the rear axle centre give 100% Ackermann?
Only roughly, and only for some rack positions. In this page's example the rule-of-thumb arms (tan β = (t/2)/L, β = 14.9°) give 102% Ackermann at full lock but 70% at half lock with the rack 130 mm behind the axle, and only 49% at full lock with the same arms and the rack ahead of the axle. Check the whole lock range with the calculator.
How do you calculate the turning radius of a car?
At low speed, with the wheels rolling without slip, the outer front wheel runs on a radius of about L / sin δo plus the scrub radius. With a 2450 mm wheelbase and 29.0° outer lock that is about 5.09 m, a turning circle of about 10.2 m. Body overhang makes the wall-to-wall circle larger.
How do you calculate steering effort?
Estimate the torque needed to twist each front tyre at standstill, divide by the steering arm's effective lever to get the tie-rod force, add the two tie-rod forces along the rack, multiply by the rack travel per radian of pinion turn and divide by the gear efficiency for the steering-wheel torque, then divide by the wheel radius for the rim force. The example (720 kg front axle, 2.2 bar) needs about 100 N at the rim of a 380 mm wheel without power assistance.
What is a good steering effort?
UN Regulation No. 79 (steering equipment) limits the steering control effort of an M1 passenger car with intact steering to 150 N in its test (a turn onto a 12 m radius within 4 s) and to 300 N with a failure in the power assistance. Parking at standstill is harder than that test, which is why most cars today use power steering.
Is this calculator accurate?
The geometry is exact for the flat (top-view) linkage it models: Skill-Lync checked the closed-form solution against an independent bisection solver on 592 wheel positions from random linkages (worst difference 2e-13°), and the effort chain against a virtual-work calculation. Real steering adds caster, kingpin inclination, camber, compliance and 3D tie-rod angles, which the page lists.
Related on Skill-Lync
- Ride frequency and motion ratio calculator
- Ackermann's principle of steering: working and applications
- Everything about Ackermann steering geometry
- Types of steering gearbox mechanisms
- Student project: steering force calculation
- Student project: steering geometry optimisation in ADAMS/Car
- All free engineering tools
Sources
- T. D. Gillespie, Fundamentals of Vehicle Dynamics, SAE, chapter 6 (low-speed turning and the Ackermann condition cot δo − cot δi = t/L) and chapter 8 (steering systems).
- W. F. Milliken and D. L. Milliken, Race Car Vehicle Dynamics, SAE, steering systems chapter (Ackermann, parallel and reverse steer, steering geometry).
- UN Regulation No. 79, Uniform provisions concerning the approval of vehicles with regard to steering equipment, steering control effort table (M1: 150 N intact, 300 N with a failure, 12 m radius, 4 s).
- Contact-patch twisting torque: uniform pressure over a disc, T = ∫ μ p ρ dA = (2/3) μ F a (the uniform-pressure clutch result, e.g. Shigley's Mechanical Engineering Design, clutches and brakes).
- Worked examples and all their numbers: Skill-Lync, checked by scripts/verify/steering.py, which re-solves the linkage by bisection on the tie-rod length, builds the ideal outer angle from the turn-centre construction, gets the rack force by virtual work and integrates the patch torque numerically, and is cross-checked against this page's calculator code at build time.