Ride frequency and motion ratio calculator

Enter the spring, motion ratio, tyre and masses for the front and rear corners and get the wheel rate, ride rate, ride frequency, wheel-hop frequency, static deflection and damping ratio, or the spring rate you need for a target frequency. Free, no sign-up, runs in your browser.

Linear quarter-car model · tyre included · checked against a time-domain simulation · Updated 16 Nov 2026

Front
Rear
Motion ratio from wishbone geometry

MR = 0.590 · ·

Sprung mass per corner = the corner's share of the car's weight minus that corner's unsprung mass. Tyre rate 0 = rigid tyre (ignored).

Ride frequency, front1.29 Hzζ = 0.30
Ride frequency, rear1.49 Hzrear 16% higher
passengersedan race / formulahigh downforce0 Hz1 Hz2 Hz3 Hz4 Hz5 Hzfront 1.29rear 1.49
FrontRear

    What is the motion ratio of a suspension?

    The motion ratio is how far the spring (or damper) moves for each millimetre the wheel moves. On most wishbone suspensions the spring sits partway along the arm, so it moves less than the wheel and MR is below 1. Because the lever cuts both the spring's travel and the force it passes to the wheel, the rate at the wheel goes with the square:

    Watch the convention. This page, like most student texts, uses spring travel over wheel travel. OptimumG's tech tips and some textbooks use wheel over spring travel, so their formula reads Kw = Ks/MR². The physics is the same; just don't mix the two.

    For a coil-over mounted on a wishbone, d1 from the inner pivot, with the wheel centre d2 from it and the spring at angle A to the arm:

    The angle term belongs inside the motion ratio, so it is squared in the wheel rate too. Writing Kw = Ks(d1/d2)² cos(90° − A), with the angle factor not squared, over-states the wheel rate of an inclined spring (by 3.5% at 75°, 15% at 60°). We checked the squared form by rotating a model wishbone through tiny angles and taking the energy stored in the spring: the wheel rate is exactly KsMR². The motion ratio also changes as the suspension moves, so measure it (or read it from a kinematics model) at ride height.

    How do you calculate ride frequency?

    The body on one corner acts like a mass on a spring. The spring it sits on is the suspension's wheel rate in series with the tyre, called the ride rate. The ride frequency is that mass-spring system's natural frequency:

    The unsprung mass (wheel, tyre, hub, brake and part of the links) has its own, much faster mode, wheel hop, where it bounces between the suspension spring and the tyre:

    These two formulas are approximations of the 2-mass quarter-car model; the calculator also gives that model's exact two natural frequencies, which differ from them by well under 1% when the unsprung mass is much lighter than the body.

    Worked example 1: a hatchback's front and rear corners

    Assumed figures for a front-engined car of about 1,200 kg: front corner 320 kg sprung and 38 kg unsprung, 26 N/mm springs at a motion ratio of 0.95 (a MacPherson strut moves almost with the wheel), tyres at 200 N/mm:

    Leaving out the tyre would give 1.36 Hz, 6% too high, because the tyre is a spring in series with the suspension. Wheel hop:

    The rear corner (222 kg sprung, 24 N/mm springs) comes out at 1.49 Hz, 16% above the front, within the 10-20% split that OptimumG recommends for a flat ride, and both are inside the 0.5-1.5 Hz passenger-car range. Under the body's weight, springs and tyres together deflect msg/Kr = 149 mm at the front.

    passengersedan race / formulahigh downforce0 Hz1 Hz2 Hz3 Hz4 Hz5 Hzfront 1.29rear 1.49
    The example's front and rear ride frequencies against the ranges in OptimumG's tech tip.

    A time-domain simulation of each 2-mass corner gives 1.288 Hz and 12.2 Hz at the front (1.288 and 12.2 Hz from the exact formula) and settles under gravity to the same 149.4 mm deflection.

    How do you calculate the damping ratio?

    The damper has a motion ratio too (often the same as the spring's, on a coil-over), so its coefficient at the wheel is cdMR². Compare it with the critical damping of the corner:

    That is close to the 0.25 OptimumG gives for passenger cars, which trade overshoot for comfort; racecars run 0.65 to 0.70 for body control. Real dampers are not linear: use the low-speed part of the damper curve, the part that controls body motion, for this number.

    Worked example 2: springs for a target ride frequency

    Working backwards, from the frequency you want to the spring you need:

    Assumed figures for a small single-seater: front corner 62 kg sprung, 13 kg unsprung, push-rod rocker with a motion ratio of 0.8 (OptimumG would call it 1.25, wheel over spring), tyre 110 N/mm, target 2.0 Hz at the front and 2.2 Hz (10% higher) at the rear (72 kg sprung):

    The rear needs 24.6 N/mm. OptimumG's formula without the tyre, Ks = 4π²f²m MR² (its MR = 1.25), gives 15.3 N/mm at the front: the soft tyre makes the right spring 10% stiffer. For a damping ratio of 0.65 the front damper needs about 1583 N·s/m at the damper. Wheel hop is 15.3 Hz.

    What this calculator does not cover

    • Roll and pitch. Anti-roll bars add stiffness in roll, not in pure bounce, so they do not change these ride frequencies; roll stiffness and pitch need a full-car model.
    • Changing motion ratio. MR varies with suspension travel and steering; this uses the value at ride height. Spring preload on an inclined spring also adds a small geometric stiffness the formula ignores.
    • Bushings, bump stops and tyre non-linearity. Rubber bushes add rate, bump stops add a lot near full bump, and tyre rate rises with pressure and load.
    • Non-linear dampers. Damping ratio here uses a linear coefficient; real dampers have different curves in bump and rebound and at low and high speed.
    • Downforce. On high-downforce cars the springs are set by ride-height control, which pushes frequencies far above comfort values.
    Design suspension

    Skill-Lync's vehicle dynamics courses take you from these hand calculations to multibody suspension models and ride and handling simulation, the work chassis teams hire for.

    Frequently asked questions

    What is the ride frequency formula?

    Ride frequency is the undamped natural frequency of the body bouncing on its suspension: f = (1/2π)√(K/m), with K the ride rate at the wheel (suspension wheel rate in series with the tyre) and m the sprung mass on that corner. A 320 kg corner on a 21.0 N/mm ride rate gives 1.29 Hz.

    What is the motion ratio formula?

    With the motion ratio defined as spring travel divided by wheel travel, the wheel rate is the spring rate times the motion ratio squared: Kw = Ks × MR². For a spring on a wishbone, MR = (d1/d2) × sin A, where d1 is the spring mount's distance from the inner pivot, d2 the wheel centre's distance and A the angle between spring and wishbone. Some books define MR the other way up (wheel/spring); then Kw = Ks / MR².

    Why is the motion ratio squared?

    Twice over, the lever works against the spring: a wheel movement compresses the spring by only MR times as much, and the spring force reaching the wheel is also reduced by MR. Force over travel at the wheel is therefore Ks × MR × MR. The same applies to the spring angle: its sine appears in the motion ratio, so it is squared in the wheel rate.

    What is a good ride frequency for a car?

    OptimumG's tech tip on springs gives 0.5 to 1.5 Hz for passenger cars, 1.5 to 2.0 Hz for sedan racecars and moderate-downforce formula cars, and 3.0 to 5.0+ Hz for high-downforce racecars. Comfort-oriented cars sit near the low end; it also recommends a rear frequency 10 to 20% higher than the front for a flat ride over bumps.

    Why should the rear ride frequency be higher than the front?

    The front wheels hit a bump first. If the rear suspension is a little stiffer (relative to its mass), the rear catches up with the front's motion and the body bounces instead of pitching. In the hatchback example the rear runs 16% higher than the front, inside the usual 10-20% split.

    What damping ratio should a car have?

    OptimumG suggests a ride damping ratio of about 0.25 for passenger cars, for comfort, and 0.65 to 0.70 as a baseline for racecars, for body control. Critical damping (1.0) is the fastest return without overshoot. Real dampers are not linear, so these refer to the low-speed (body-motion) part of the damper curve.

    Is this calculator accurate?

    For the linear quarter-car model, yes: Skill-Lync checked the motion-ratio formula on a planar wishbone, and the ride, wheel-hop and 2-mass frequencies and the static deflection against time-domain simulations (the 2-mass frequencies agree to within 0.0003% on 8 random corners). Real cars add anti-roll bars, bushings, damper non-linearity and changing motion ratio with travel.

    Related on Skill-Lync

    Sources

    • M. Giaraffa, OptimumG Tech Tips, Springs & Dampers, Part One (ride frequency ranges, the 10-20% front-to-rear split, Ks = 4π²f²m MR² with MR = wheel/spring travel, worked example 49,348 N/m) and Part Three (critical damping, ride damping ratios of about 0.25 for passenger cars and 0.65-0.70 for racecars).
    • T. D. Gillespie, Fundamentals of Vehicle Dynamics, SAE, chapter 5 (ride: the quarter-car model, ride rate with the tyre in series, body and wheel-hop frequencies).
    • W. F. Milliken and D. L. Milliken, Race Car Vehicle Dynamics, SAE (installation ratio and wheel rate, ride frequencies).
    • Worked examples and all their numbers: Skill-Lync, checked by scripts/verify/ride.py, which derives the motion ratio and wheel rate from a planar wishbone, simulates each quarter car (RK4) for its natural frequencies and static deflection, and is cross-checked against this page's calculator code at build time.
    Free counselling

    Go from hand calcs to suspension design.

    Suspension and vehicle dynamics roles want engineers who can model a car in ADAMS or MotionSolve, not just its formulas. A Skill-Lync counsellor can map the course that fits the role you want.

    Talk to a vehicle dynamics course counsellor

    Free. We call you back, usually the same day.

    By submitting you agree to our Terms and Privacy Policy.

    Talk to a career counsellor

    Talk to a career counsellor

    Free 20-minute call. We'll map the right course to where you want to work.

    By submitting you agree to our Terms and Privacy Policy.