Gradeability calculator for trucks, buses and EVs
Enter the weight, torque, gear ratios, tyre and grip, and get the steepest grade the vehicle can climb in each gear, whether torque or tyre grip sets the limit, the India AIS-003 7° check, the speed it holds on a grade and the gear ratio it needs. Diesel or electric. Free, no sign-up, runs in your browser.
Quasi-static force balance · exact grade formula · checked by a separate solver · Updated 18 Nov 2026
Presets: GVW, torque, power and tyre size are from the OEM spec pages cited in our gradeability guide; ratios, efficiency, Crr, drag area and axle loads are assumed. Typical Crr: 0.005-0.008 truck tyres on good roads, 0.01-0.02 on rough or unpaved roads.
| Gear | Overall ratio | Peak wheel force | Grade on torque |
|---|
AIS-003: correct a test result to rated weight
Starting gradeability at rated weight: 14.4% (8.2°)
What is gradeability?
Gradeability is the steepest road gradient a vehicle can climb at its full rated weight (GVW, or GCW for a tractor-trailer), quoted as a percentage. It is set by the force the engine or motor delivers at the driven wheels and by how much of that force the tyres can pass to the road. India's legal minimum under AIS-003 is 7°, which is 12.3%.
Percent grade is rise over run, 100 × tan θ, so percent and degrees are not the same number:
| Grade (%) | 5 | 7 | 10 | 12.28 | 17 | 25 | 32 | 50 | 100 |
|---|---|---|---|---|---|---|---|---|---|
| Slope (°) | 2.9 | 4.0 | 5.7 | 7.0 | 9.6 | 14.0 | 17.7 | 26.6 | 45.0 |
Spec sheets for Indian trucks and buses usually quote 17-35%. A 12 m city e-bus typically lists 17%, the figure the Urban Bus Specifications II (2013) set; an electric tipper like the Tata Prima E.28K lists 32% (OEM pages, read 16 Nov 2026). Highway design grades are far gentler: the Indian Roads Congress ruling gradient is 3.3% in plain terrain, 5% in hills and 6% in steep terrain.
How does this gradeability calculator work?
It balances the force at the driven wheels against the three resistances on a slope: the component of weight pulling the vehicle back down, tyre rolling resistance and air drag. The steepest grade is where the two are equal; the calculator solves that exactly in every gear, then caps it at the grip of the driven tyres.
T is the engine or motor torque, ig and i0 the gearbox and final-drive ratios, η the driveline efficiency, r the loaded tyre radius, m the gross mass and Crr the rolling resistance coefficient. Dividing by mg and solving sin θ + Crr cos θ = k gives the slope directly:
The common shortcut G = 100 × (force ÷ weight) treats k as tan θ when it is really sin θ plus rolling resistance. It is close below about 15% and drifts on steep grades. The grip limit uses the load on the driven axles, md; on a slope that load falls with cos θ, like the rolling resistance, so the cos θ cancels:
Rated or peak torque is used for the crawl (starting) value: a diesel slips its clutch to start, and an electric motor gives full torque from zero speed. For gradeability at speed, the engine follows a simple full-load curve (flat peak torque between two speeds, then falling to rated power), and the motor gives constant torque up to its base speed and constant power above it:
Worked example 1: is a 55 t tractor-trailer limited by torque or by grip?
The truck preset uses the OEM figures of a common Indian 55-tonne 4x2 tractor (1,100 N·m from 1,100 to 1,700 rpm, 224 kW at 2,300 rpm, GCW 55,000 kg). The 9-speed ratios, 4.88 axle, 0.495 m tyre radius, 88% efficiency and 11 t on the single drive axle are Skill-Lync's assumptions. First gear:
Enough torque for 22.4%, but the drive tyres can only pass a fraction of it:
On a wet road (μ 0.4) the limit is 7.3%, below the 12.3% AIS-003 asks for, which is why the test is run on a dry surface. A 6x4 with 22 t on its driven bogie lifts the grip limit to 27.3% dry and 15.3% wet. Higher gears give 14.5%, 10.0%, 7.2%, 5.2% in 2nd to 5th.
What a fleet buyer feels is speed on a long climb. On the full-load curve this rig holds the IRC design gradients at:
| Grade | Highest steady speed | Gear, engine speed |
|---|---|---|
| 3.3% (plain terrain) | 31.0 km/h | 6th, 2,025 rpm |
| 5% (hilly) | 20.9 km/h | 5th, 1,825 rpm |
| 7% (steep, limiting) | 15.4 km/h | 4th, 1,795 rpm |
So a loaded 55 t rig crawls up a 7% ghat at about 15 km/h on 224 kW. Power, not torque, sets climbing speed: at constant speed the power needed is force × speed, and on a 7% grade the grade force alone is about 37.7 kN.
Worked example 2: what gear ratio does a 12 m e-bus need?
The bus preset uses a 19.5 t GVW and a 2,950 N·m, 245 kW motor (Tata Starbus 4/12 EV spec page) on a 0.488 m tyre radius, with 95% efficiency and Crr 0.007 assumed. To pass the AIS-003 7° minimum on peak torque it needs only:
The 17% buyers specify needs 5.81:1. With a 5.8:1 single reduction the bus crawls up 17.0% and its tyres could pass 44.8% dry (65% of the weight on the driven rear axle, assumed), so it is torque-limited. The motor hands over to constant power at 25.2 km/h; above that gradeability falls fast:
| Speed | 10 km/h | 30 km/h | 40 km/h | 50 km/h | 60 km/h |
|---|---|---|---|---|---|
| Grade held | 16.9% | 13.9% | 10.1% | 7.8% | 6.2% |
On peak power it holds 54.6 km/h on 7% and 70.0 km/h on 5%. These are peak ratings: a motor sustains peak torque and power only for a limited time before it heats up, so a long ghat climb is a thermal question as well as a gearing one. The tipper preset checks the Tata Prima E.28K's 32% claim: with an assumed 16.6:1 overall reduction it crawls up 32.0%, and its 6x4 bogie (75% of the weight, assumed) grips 51.5% dry but only 29.0% wet.
How is starting gradeability tested under AIS-003?
The loaded vehicle is parked facing uphill on a dry asphalt or concrete gradient, started from neutral in its lowest gear with the air conditioner off, and must pull away without excessive shudder three times out of three. If the ramp is steeper than needed, the load is reduced until the vehicle only just starts, and the result is corrected to rated weight:
That bus clears the 7° minimum. The correction is in the calculator, under the chart. AIS-049 runs the same test on battery-electric vehicles with the pack at 60% state of discharge.
What this calculator does not cover
- Clutch and launch. Starting on a slope also needs the clutch to survive the slip and the engine not to stall; AIS-003 checks for shudder. This calculator gives the crawl force from peak torque, an upper bound.
- Load transfer. Climbing moves weight onto the rear axle, which helps a rear-drive vehicle. The grip limit ignores it, so it is slightly conservative for rear drive and optimistic for front drive.
- The real torque curve and thermal limits. The engine curve is simplified and the motor figures are peak values; use measured full-load curves and continuous ratings for a long climb.
- Gear changes on a grade. A heavy truck loses speed during every shift on a steep climb; the speeds shown are steady-state, with no shifting.
- Altitude. Air density is the AIS-003 reference 1.168 kg/m³, and a naturally aspirated or turbo diesel loses power at altitude.
Skill-Lync's EV and vehicle dynamics courses take you from this force balance to sizing motors, ratios and batteries against drive cycles and grades, the work powertrain teams hire for.
Frequently asked questions
What is gradeability of a vehicle?
Gradeability is the steepest slope a vehicle can climb at its full rated weight, written as a percentage: 100 × tan θ. A 17% grade rises 17 m in 100 m and is a 9.6° slope, not 17°. It is limited by the force the engine or motor delivers at the wheels and by the grip of the driven tyres.
How do you calculate gradeability?
Work out the force at the wheels: torque × gearbox ratio × final-drive ratio × driveline efficiency ÷ loaded tyre radius. Subtract air drag (negligible at crawl speed) and divide by the vehicle's weight m·g to get k. Solve sin θ + Crr cos θ = k for θ; gradeability is 100 tan θ. Then cap it at the grip limit, 100 × (μ × driven-axle mass ÷ total mass − Crr).
What gradeability does India require?
AIS-003 requires every vehicle, except two-wheelers of 70 cc or less with a fixed ratio, to start from rest on a 7° slope (12.3%) at its full GVW or GCW, three times out of three, on a dry surface. AIS-049 applies the same test to battery-electric vehicles at 60% state of discharge.
Is 17% gradeability the same as 17 degrees?
No. Percent grade is 100 × tan θ, so 17% is 9.6°; a 17° slope would be 30.6%. The two are close only on gentle slopes, and 100% is 45°. Convert everything to percent before comparing spec sheets.
Why does gradeability fall with speed?
In a high gear the overall ratio is small, so the wheel force is small; and above its base speed an electric motor runs at constant power, so wheel force falls as P/v. In this calculator's 12 m e-bus example, 17.0% at crawl becomes 7.8% at 50 km/h.
What is the difference between starting and maximum gradeability?
Starting gradeability is the steepest slope a loaded vehicle can pull away on from standstill in its lowest gear; it is what AIS-003 tests and it is hard on the clutch and tyre grip. Maximum (crawl) gradeability is the steepest slope it can keep climbing at very low speed. This calculator gives the crawl value from peak torque, an upper bound on the starting figure.
Is this calculator accurate?
For the quasi-static force balance, yes: Skill-Lync re-solved every worked example and 40 random vehicles by bisection in a separate Python script, and the page's code agrees to within 1e-7. The answer is only as good as the inputs: torque curve, efficiency, rolling resistance and especially tyre grip.
Related on Skill-Lync
- Gradeability of commercial vehicles: formula, worked examples, AIS-003
- The powertrain of an ICE vehicle vs an electric vehicle
- Student project: vehicle dynamics, force, power and torque
- Student project: design of an electric vehicle
- Vehicle dynamics courses compared
- Ride frequency and motion ratio calculator
- All free engineering tools
Sources
- ARAI, AIS-003: Automotive vehicles, starting gradeability, method of test and requirements (7° minimum at GVW/GCW, test procedure, weight correction, reference air density) and AIS-049 (battery-electric vehicles, 60% state of discharge).
- Ministry of Urban Development, Urban Bus Specifications II (2013): 17% gradeability for city buses.
- OEM spec pages, read 16 Nov 2026: Tata Starbus 4/12 EV, Tata Signa 5530.S, Tata Prima E.28K.
- Indian Roads Congress ruling, limiting and exceptional gradients, as summarised in NPTEL Transportation Engineering.
- T. D. Gillespie, Fundamentals of Vehicle Dynamics, SAE, chapters 2-3 (tractive effort, rolling resistance, grade and aerodynamic resistance).
- Worked examples and all their numbers: Skill-Lync, checked by scripts/verify/gradeability.py, which solves the force balance by bisection and finds speed-on-grade by a dense scan, and is cross-checked against this page's calculator code at build time.