
Automobile Engineering
Spin a crank and size its flywheel, shift through a gearbox against the road load, hold a planet carrier, steer with Ackermann, brake with and without ABS and read a tyre's sidewall
21 chapters, 25 interactives, few words. Every chapter is mapped to the Anna University, VTU, SPPU, Mumbai University and KTU units it covers: vehicle layouts and chassis, resistances and aerodynamics, engine components and the slider-crank, flywheels, valve timing and VVT, petrol and diesel injection, ignition and engine management, turbochargers, emissions and BS VI, clutches, gearboxes, automatic transmissions, the driveline and differential, steering geometry, suspension, brakes, ABS and EBD, tyres, alternative fuels, and electric, hybrid and fuel cell vehicles. MU rows follow MEDLO7031 Automotive Power Systems; MEDLO7033 Vehicle Systems is in the same scheme but its unit list is not published online.
- AUCME380Automobile Engineering
- VTUBME654DModern Mobility
- SPPU402044AAutomobile Design
- MUMEDLO7031Automotive Power Systems
- KTUMET352Automobile Engineering
By Skill-Lync · Updated 17 Nov 2026 · 21 chapters · 25 interactives · free, no sign-up
Vehicle types, layouts, chassis, frame and body
Which syllabus covers thisAU CME380 Unit IVTU BME654D Module 1SPPU not in syllabusMU not in syllabusKTU MET352 Module 1
How are automobiles classified?
By purpose: passenger vehicles (two-wheelers, three-wheelers, cars), goods vehicles (light commercial vehicles, trucks, tractors) and passenger carriers (vans, buses). By power source: petrol, diesel, CNG, LPG, electric and hybrid. By the wheels driven: front-wheel drive, rear-wheel drive, four-wheel drive or all-wheel drive. By body: hatchback, sedan (notchback), estate, SUV, MUV, pick-up, coupe and convertible. By load: light and heavy vehicles. Each choice trades cost, space, grip and efficiency, which is why one manufacturer sells several at once.
What are the common engine and drive layouts?
Front engine, front-wheel drive packs the engine, gearbox and differential together at the front, frees cabin space and puts weight on the driven wheels, so most hatchbacks and compact sedans use it. Front engine, rear-wheel drive splits the load more evenly and is common on body-on-frame SUVs, pick-ups and trucks. A rear engine with rear drive, as on the Tata Nano, keeps the front light. Mid-engine layouts, between the axles, suit sports cars. Four-wheel drive adds a transfer case so both axles can be driven on bad roads.
What is the difference between a ladder frame and a monocoque?
A ladder frame is two long side members joined by cross members. The engine, suspension and a separate body bolt onto it. It is strong, easy to repair and tolerates overloading, so trucks, buses and many rugged SUVs use it. A monocoque (unitary or frameless construction) makes the welded steel body shell itself carry the loads. It is lighter and stiffer in twist for its weight and absorbs crash energy better in designed crumple zones, so nearly every modern car uses one. A sub-frame, a small frame carrying the engine or suspension, is often bolted to a monocoque.
What loads does a chassis frame carry?
Bending from the weight of the body, engine, passengers and cargo, which bows the frame between the axles. Torsion when diagonally opposite wheels hit a bump, twisting the frame along its length. Lateral loads in cornering and from side winds. Longitudinal loads when accelerating and braking, which also shift weight between the axles. Impact loads from potholes and collisions. Fatigue from millions of smaller repeated loads. The frame or body must be stiff enough that the suspension geometry stays where the designer put it, not just strong enough not to break.
How is a car's weight shared between its axles, and why does it shift?
Take moments about each contact patch. A centre of gravity (CG) a metres behind the front axle, on a wheelbase L, puts mg·b/L on the front axle, where b = L − a. When the car accelerates, the inertia force acts at the CG, at height h, and moves m·a_x·h/L from the front to the rear axle. Braking does the opposite, which is why front brakes are bigger. A slope adds a component of weight along the road that shifts load toward the lower axle. Slide the CG and acceleration to see each effect.
A 60:40 front-heavy hatchback (CG 0.55 m high, 2.5 m wheelbase) brakes at 0.8 g. Its front axle now carries about:
The inertia force at the CG moves m·0.8g·h/L = 2,072 N forward, so the front axle goes from 7,063 N to 9,135 N, 78% of the car's weight.
Worked examples
Static axle loads and load transfer under braking · m = 1,200 kg, L = 2.5 m, CG 1.0 m behind the front axle and 0.55 m high; braking at 0.8 g
- b = 2.5 − 1.0 = 1.5 m
- Front: W_f = mg·b/L = 1,200 × 9.81 × 1.5 / 2.5 = 7,063.2 N (720 kg)
- Rear: W_r = mg·a/L = 4,708.8 N (480 kg)
- Transfer: ΔW = m·0.8g·h/L = 1,200 × 0.8 × 9.81 × 0.55 / 2.5 = 2,071.9 N
- Braking: W_f = 9,135.1 N, W_r = 2,636.9 N
Answer: 7,063 N / 4,709 N parked; 9,135 N / 2,637 N while braking (77.6% on the front)
Grip-limited acceleration: front-wheel drive against rear-wheel drive · Same car, tyre-road friction μ = 0.9, level road
- FWD: driving force μ·W_f with W_f = (mg·b − m·a·h)/L; set it equal to m·a
- a = μg·b/(L + μh) = 0.9 × 1.5 / (2.5 + 0.9 × 0.55) g = 0.451 g
- RWD: a = μg·a_cg/(L − μh) = 0.9 × 1.0 / (2.5 − 0.495) g = 0.449 g
- FWD starts with more weight on the driven wheels, but acceleration moves load to the rear, so the two end up almost equal
Answer: FWD 0.451 g, RWD 0.449 g
Axle loads on a 20% gradient · Same car parked facing uphill on a 1-in-5 (20%) slope
- θ = tan⁻¹ 0.20 = 11.31°
- W_f = mg(b cos θ − h sin θ)/L = 11,772 × (1.5 × 0.9806 − 0.55 × 0.1961) / 2.5 = 6,418.1 N
- W_r = mg(a cos θ + h sin θ)/L = 5,125.3 N
- Check: W_f + W_r = mg cos θ = 11,543.4 N; the rest of the weight, mg sin θ = 2,309 N, is held by the brakes
Answer: 6,418 N front, 5,125 N rear
Vehicle resistances and aerodynamics
Which syllabus covers thisAU CME380 Unit IVTU not in syllabusSPPU 402044A Unit 4MU not in syllabusKTU MET352 Module 5
What forces resist a moving vehicle?
Four. Rolling resistance, from the tyre flexing as it rolls. Aerodynamic drag, from pushing air aside. Gradient resistance, the component of weight along a slope. Inertia, the force needed to accelerate the mass, including a little extra for the rotating wheels and engine parts. The sum is the tractive effort the wheels must supply, and tractive effort times speed is the power needed. Engines, gear ratios and batteries are all sized from this one equation.
What causes rolling resistance?
A tyre squashes where it meets the road and springs back as it leaves. The rubber does not give all that energy back: some turns into heat (hysteresis). The result is a drag force roughly proportional to the load, F = f_r·W. Typical coefficients are about 0.010 to 0.015 for car tyres on good asphalt and lower, around 0.006 to 0.008, for truck tyres. Under-inflation, soft or rough roads and heavy tread all raise it. At town speeds rolling resistance is usually larger than air drag.
Why does aerodynamic drag matter so much at highway speed?
Drag force grows with the square of speed, F = ½ρC_dAv², so the power to overcome it grows with the cube. Going 20% faster needs about 73% more power just for the air. C_d, the drag coefficient, says how slippery the shape is; A is the frontal area. Most car drag is pressure drag from the low-pressure wake behind the body. Skin friction, the wheels, mirrors, the cooling airflow and trailing vortices add the rest. Slide the speed to find where drag overtakes rolling resistance.
What are aerodynamic lift and the aerodynamic moments?
Air flowing faster over the curved roof than under the floor creates lift, F_L = ½ρC_LAv². Lift unloads the tyres, so grip and steering feel fall at speed. Because lift is not split evenly, it also creates a pitching moment that can unload the rear axle more than the front. Side winds add a side force and a yawing moment that try to turn the car. Front air dams, a low nose, smooth underbodies, rear spoilers and, on race cars, inverted wings (negative lift) reduce lift or turn it into downforce.
How do body shape details reduce drag?
Air should stay attached to the body as long as possible and leave it cleanly. A rounded front, chamfered edges, a raked windscreen and a sloping bonnet help the front. At the back, a gently tapering roof (fastback) or a sharply cut tail with a small spoiler keep the wake small. A squareback (most hatchbacks) has a large wake and more drag. A notchback (sedan) sits in between. Smooth underbody panels, wheel covers, small mirrors and an upward-tapered rear floor all chip away at C_d.
Going from 100 to 120 km/h (20% faster), the power needed to beat air drag rises by about:
Drag power goes with v³: 1.2³ = 1.728. For a typical hatchback that is 8.6 kW at 100 km/h and 14.9 kW at 120 km/h.
Worked examples
Drag force and power of a hatchback · C_d = 0.32, A = 2.1 m², ρ = 1.2 kg/m³ (typical values)
- 100 km/h = 27.78 m/s; F = ½ × 1.2 × 0.32 × 2.1 × 27.78² = 311.1 N
- P = F·v = 311.1 × 27.78 = 8.64 kW
- 120 km/h: F = 448.0 N (× 1.44), P = 14.93 kW (× 1.728)
Answer: 311 N and 8.64 kW at 100 km/h; 14.93 kW at 120 km/h
Tractive effort and power on a climb · 1,100 kg hatchback at 80 km/h up a 4% gradient; f_r = 0.012, C_d = 0.32, A = 2.1 m², steady speed
- θ = tan⁻¹ 0.04 = 2.291°, v = 22.22 m/s
- Rolling: 0.012 × 1,100 × 9.81 × cos θ = 129.4 N
- Gradient: 1,100 × 9.81 × sin θ = 431.3 N
- Air: ½ × 1.2 × 0.32 × 2.1 × 22.22² = 199.1 N
- Total 759.8 N × 22.22 m/s = 16.88 kW at the wheels
Answer: 760 N, 16.9 kW at the wheels
Speed at which drag equals rolling resistance · Hatchback: 1,100 kg, f_r 0.012, C_dA = 0.672 m². Truck: 16,000 kg, f_r 0.007, C_dA = 4.875 m²
- ½ρC_dAv² = f_r·m·g gives v = √(2 f_r m g / (ρ C_d A))
- Hatchback: v = √(2 × 0.012 × 1,100 × 9.81 / (1.2 × 0.672)) = 17.92 m/s = 64.5 km/h
- Truck: v = √(2 × 0.007 × 16,000 × 9.81 / (1.2 × 4.875)) = 69.8 km/h
- Above these speeds the air takes more power than the tyres
Answer: about 65 km/h for the car and 70 km/h for the truck
Engine components, materials and the slider-crank
Which syllabus covers thisAU CME380 Unit IVTU BME654D Module 1SPPU 402044A Unit 1MU MEDLO7031 Module 1KTU MET352 Module 4
What are the main parts of an IC engine and what does each do?
The cylinder block holds the cylinders and coolant passages. The cylinder head closes the top and carries the valves, ports and spark plug or injector. The piston takes the gas pressure, the piston rings seal it, and the gudgeon pin joins the piston to the connecting rod. The connecting rod turns the piston's up-and-down motion into rotation of the crankshaft. The camshaft opens the valves. The flywheel smooths the speed. The oil sump, manifolds and gaskets complete the engine.
What are engine parts made of, and why?
Blocks are grey cast iron (cheap, damps vibration, wears well) or aluminium alloy with iron liners or coated bores (lighter). Heads are aluminium alloy because it conducts heat away quickly. Pistons are aluminium-silicon alloy: light, conductive, and the silicon cuts thermal expansion. Rings are cast iron or steel, often chromium-plated or nitrided for wear. Connecting rods and crankshafts are forged steel, or nodular (SG) cast iron for cheaper crankshafts. Exhaust valves run red hot, so they use heat-resisting austenitic steels; intake valves use alloy steel.
Why does a piston carry more than one ring?
The top one or two are compression rings. Gas pressure pushes them down and outward against the cylinder wall, so they seal the combustion gas and conduct heat from the piston crown to the cooled wall. Gas that leaks past them into the crankcase is called blow-by. The bottom ring is the oil control ring: it scrapes surplus oil off the wall and returns it through slots, leaving a thin film. Worn oil rings are why an old engine burns oil and smokes blue.
How fast does a piston move and accelerate?
The piston, rod and crank form a slider-crank. With crank radius r and rod length l, the ratio n = l/r is usually about 3 to 4. The piston speed is zero at the dead centres and peaks a little before 90° of crank angle. Its acceleration is largest at top dead centre, rω²(1 + 1/n), because the rod's angle adds to the crank's motion there. At 6,000 rpm a piston in an 80 mm stroke engine reaches about 2,000 g at TDC, so light pistons matter.
What are primary and secondary inertia forces?
The reciprocating mass m (piston, rings, pin and about a third of the rod) needs a force m·a to accelerate. Using the approximate acceleration, that force has a primary part m r ω² cos θ, at crank frequency, and a secondary part m r ω² cos 2θ / n, at twice crank frequency. In an inline four the primary forces of the four cylinders cancel, but the secondary forces add up, which is why some larger four-cylinder engines carry two balancer shafts spinning at twice crank speed. Counterweights on the crank balance the rotating masses.
Fit a longer connecting rod (larger n = l/r) with the same crank. The piston's peak acceleration at TDC:
At TDC a = rω²(1 + 1/n). Raising n from 3 to 4 cuts the bracket from 1.333 to 1.250, so peak acceleration and the inertia force both fall by about 6%.
Worked examples
Mean and maximum piston speed · Stroke 80 mm (r = 40 mm), n = l/r = 3.5, 6,000 rpm
- Mean piston speed = 2 × stroke × N / 60 = 2 × 0.08 × 6,000 / 60 = 16.0 m/s
- ω = 2π × 6,000 / 60 = 628.3 rad/s
- Differentiating x(θ) and searching over the stroke: v_max = 26.14 m/s at θ = 75° after TDC
- That is 1.63 times the mean speed
Answer: 16 m/s mean, 26.1 m/s peak at 75°
Inertia force at TDC against the gas force · Same engine; reciprocating mass 0.5 kg; bore 75 mm; peak cylinder pressure 60 bar (gauge 59 bar)
- a_TDC = rω²(1 + 1/n) = 0.04 × 628.3² × (1 + 1/3.5) = 20,303 m/s² (2,070 g)
- Inertia force = 0.5 × 20,303 = 10,152 N
- Gas force = 59 × 10⁵ × π/4 × 0.075² = 26,065 N
- Near TDC on the exhaust stroke there is no gas force to offset it, so the inertia force alone pulls on the rod and big-end bolts
Answer: 10.15 kN inertia against 26.1 kN peak gas force
Secondary inertia force of an inline four · Same piston and crank, 6,000 rpm, four cylinders
- Secondary force per cylinder, amplitude m r ω² / n = 0.5 × 0.04 × 628.3² / 3.5 = 2,256 N
- Crank throws at 0°, 180°, 180°, 0°: the cos θ terms cancel, the cos 2θ terms are all in phase
- Net shaking force = 4 × 2,256 = 9,024 N, at 2 × 100 = 200 Hz
Answer: 9.02 kN vertical shaking force at 200 Hz
Crankshaft, turning moment and the flywheel
Which syllabus covers thisAU CME380 Unit IVTU not in syllabusSPPU 402044A Unit 1MU not in syllabusKTU MET352 Module 4
What does a crankshaft look like and what decides its shape?
A crankshaft has main journals that turn in the main bearings, crank pins that carry the connecting rods, webs that join them, and counterweights opposite the pins. The angle between the throws sets the firing interval: 180° apart in an inline four, so a cylinder fires every 180° of crank rotation. The firing order, commonly 1-3-4-2 in a four, spreads the loads along the shaft. The shaft must resist bending from gas forces, twisting from torque and torsional vibration, so the fillets between pins and webs are rolled or hardened.
What is a turning moment diagram?
A plot of crankshaft torque against crank angle over one cycle (720° for a four-stroke). The torque comes from the force along the piston, gas pressure minus the inertia force, multiplied by how far the piston moves per radian of crank, dx/dθ. In a single cylinder only the power stroke gives positive torque; the compression stroke takes torque back. The area under the curve is the work per cycle, and its average is the mean torque the engine delivers to a steady load. Change the cylinder count to see the curve smooth out.
What are fluctuation of energy and coefficient of fluctuation of speed?
When the engine torque is above the mean, the surplus energy speeds the crankshaft up; when it is below, the shaft slows. Add up the areas between the torque curve and the mean line: the difference between the highest and lowest running total is the maximum fluctuation of energy, ΔE. The coefficient of fluctuation of speed, C_s = (ω_max − ω_min)/ω_mean, is the speed swing the design allows. Typical design values are tighter for generator sets than for vehicles, which also have the driveline's inertia helping.
How is a flywheel sized, and what limits its size?
From ΔE = Iω²C_s, the inertia needed is I = ΔE/(ω²C_s). For a rim-type flywheel most of the inertia sits in the rim, so I ≈ m·R², with R the mean rim radius. A bigger radius gives the same inertia with much less mass, but the rim stress grows with rim speed: for a thin rotating rim the hoop stress is σ = ρv², whatever the rim's thickness. So the radius is limited by the material's allowable stress and by the space in the bell housing.
Why do multi-cylinder engines need smaller flywheels?
Each cylinder's power stroke fills in the gaps of the others. An inline four fires every 180°, so its torque never dips as deeply below the mean and the energy swing per cycle is a small fraction of a single cylinder's, even though it makes four times the power. Lighter flywheels let the engine rev up faster. Many diesel cars use a dual-mass flywheel: two masses joined by springs that soak up the torsional pulses before they reach the gearbox.
A single-cylinder engine becomes an inline four by adding three identical cylinders firing at even intervals. At the same speed the energy swing ΔE:
In the idealised engine of the interactive at 3,000 rpm, ΔE drops from 295 J to 48 J while the mean torque quadruples from 20.5 to 81.8 N·m.
Worked examples
Flywheel from the turning-moment areas · Areas between the torque curve and the mean line over one cycle: +420, −160, +80, −340 J; 2,400 rpm; speed within ±1% (C_s = 0.02); rim radius 180 mm
- Running total of energy: 0, 420, 260, 340, 0 J
- ΔE = max − min = 420 − 0 = 420 J
- ω = 2π × 2,400 / 60 = 251.33 rad/s; I = ΔE/(ω²C_s) = 420 / (251.33² × 0.02) = 0.3325 kg·m²
- Rim mass ≈ I/R² = 0.3325 / 0.18² = 10.26 kg
Answer: I = 0.332 kg·m², a rim of about 10.3 kg
Single cylinder against inline four (idealised full load) · 353 cc per cylinder, CR 10, polytropic 1.3, pressure × 3 at TDC, 0.5 kg reciprocating mass, 3,000 rpm, C_s = 0.02
- Single cylinder: mean torque 20.45 N·m (6.43 kW), ΔE = 295 J
- I = 295 / (314.2² × 0.02) = 0.1492 kg·m²
- Inline four (fires every 180°): mean torque 81.81 N·m, ΔE = 47.9 J, I = 0.0243 kg·m²
- Four times the torque with a flywheel 6.1 times smaller
Answer: 0.149 kg·m² for the single, 0.024 kg·m² for the four
Hoop stress in a flywheel rim · Steel rim (ρ = 7,850 kg/m³), mean radius 150 mm, 6,000 rpm
- Rim speed v = ωR = 628.3 × 0.15 = 94.2 m/s
- σ = ρv² = 7,850 × 94.2² = 69.7 MPa
- The thickness does not appear: a thicker rim adds mass and the force to hold it in equal proportion
Answer: 69.7 MPa
Valve train and variable valve timing
Which syllabus covers thisAU CME380 Unit IVTU BME654D Module 1SPPU not in syllabusMU MEDLO7031 Module 3KTU not in syllabus
How does the valve train open and close the valves?
Poppet valves sit in the cylinder head and are held shut by springs. A camshaft, driven by a belt, chain or gears at half crank speed, pushes them open once per four-stroke cycle. In older pushrod (overhead valve) engines the cam sits in the block and acts through tappets, pushrods and rockers. Overhead cam (OHC) engines put the cam on the head; double overhead cam (DOHC) engines have one camshaft for the intake valves and one for the exhausts, which suits four valves per cylinder and lets each cam be phased separately.
Why do valves open before and close after the dead centres?
Gas has inertia and a valve takes time to lift. Opening the exhaust valve about 40° before bottom dead centre lets most of the burnt gas blow down before the piston starts pushing it out. Closing the intake valve about 40° after BDC uses the momentum of the incoming air to keep filling the cylinder while the piston starts rising. The intake opens a little before TDC and the exhaust closes a little after, so both are open together. A valve timing diagram draws these angles round a circle.
What is valve overlap and why does it matter?
Overlap is the period near TDC at the end of the exhaust stroke when both valves are open. At high speed the outgoing exhaust helps pull fresh charge in (scavenging), which raises power. At idle and low speed, with little gas momentum and low manifold pressure, exhaust flows back into the intake instead. That dilutes the charge, makes idling rough and raises unburnt hydrocarbons. A fixed cam has to compromise between the two, which is the case for variable timing.
What does variable valve timing do?
A cam phaser, usually a vane unit on the camshaft sprocket fed by engine oil and controlled by a solenoid valve from the engine ECU, rotates the camshaft relative to its sprocket by up to a few tens of crank degrees while the engine runs. Advancing the intake cam at low and medium speed closes the intake earlier, trapping more charge for torque, and adds overlap for internal exhaust gas recirculation at part load. Retarding it at high speed suits the air's momentum. Variable lift systems, such as Honda's VTEC, switch between cam profiles as well.
What is effective compression ratio, and how do Atkinson-cycle engines use it?
Compression only starts when the intake valve closes. If the intake closes well after BDC, some charge is pushed back out and the effective compression ratio, the cylinder volume at intake closing divided by the clearance volume, is below the geometric ratio. Engines for hybrids use this deliberately (an Atkinson or Miller cycle): a high geometric ratio gives a long expansion stroke and good efficiency, while late intake closing keeps compression, and knock, in check. The penalty is lower torque, which the electric motor fills in.
Advance the intake cam by 30° and leave the exhaust cam alone. The valve overlap:
The intake now opens 30° earlier, at 40° BTDC instead of 10°, while the exhaust still closes at 10° ATDC, so the overlap grows from 20° to 50°.
Worked examples
Durations and overlap from a timing diagram · IVO 10° BTDC, IVC 40° ABDC, EVO 40° BBDC, EVC 10° ATDC; 3,000 rpm
- Intake: 10 + 180 + 40 = 230° of crank; exhaust: 40 + 180 + 10 = 230°
- Overlap: 10 + 10 = 20°
- Camshaft turns at half speed: the intake cam lobe acts for 115° of cam rotation
- At 3,000 rpm one degree takes 1/18,000 s: intake open 12.78 ms, overlap 1.11 ms
Answer: 230° each, 20° overlap; 12.8 ms and 1.11 ms at 3,000 rpm
Effective compression ratio and late intake closing · Geometric CR 10.5, n = l/r = 3.5; intake closing 40° ABDC against 70° ABDC
- Piston travel from TDC: x/r = 1 − cos θ + n(1 − √(1 − sin²θ/n²)), with θ measured back from compression TDC
- IVC 40° ABDC → θ = 140° before TDC → piston at 91.3% of the stroke → ECR = 1 + 9.5 × 0.9128 = 9.67
- IVC 70° ABDC → θ = 110° → 73.5% of the stroke → ECR = 7.98
Answer: 9.67 : 1 and 7.98 : 1
What a 30° intake advance changes · Base timing above; intake cam advanced 30° by the phaser
- IVO: 10° + 30° = 40° BTDC; IVC: 40° − 30° = 10° ABDC
- Overlap: 40 + 10 = 50°
- Effective CR with IVC 10° ABDC: 10.45, up from 9.67, so more charge is trapped at low speed
Answer: overlap 50°, ECR 10.45
Petrol fuel injection: carburettor, MPFI and GDI
Which syllabus covers thisAU CME380 Unit IIVTU BME654D Module 1SPPU 402044A Unit 1MU MEDLO7031 Module 1KTU MET352 Module 4
How did a carburettor meter fuel, and why was it replaced?
Air rushing through a narrow throat (venturi) drops in pressure, and that suction draws petrol from a float chamber through a calibrated jet. The throttle valve below it sets the airflow. Extra circuits handled idling, acceleration and cold starts. But a carburettor cannot hold the mixture accurately across all speeds, loads, altitudes and temperatures. Catalytic converters need the mixture held very close to chemically correct, so emission norms (Bharat Stage norms in India) pushed cars to electronic fuel injection; two-wheelers followed with BS VI from 2020.
What are air-fuel ratio and lambda?
The air-fuel ratio is the mass of air per unit mass of fuel. Burning petrol completely needs about 14.7 kg of air per kg of fuel, the stoichiometric ratio. Lambda (λ) is the actual ratio divided by the stoichiometric one: λ = 1 is chemically correct, λ < 1 is rich (extra fuel) and λ > 1 is lean (extra air). Full power wants slightly rich, about λ 0.85 to 0.9. Light cruising can run leaner in some engines. A three-way catalyst only works well very close to λ = 1.
How does a multi-point fuel injection (MPFI) system work?
An electric pump in the tank sends petrol through a filter to a fuel rail held at about 3 to 4 bar. Each cylinder has a solenoid injector in its intake port, spraying onto the back of the intake valve. The engine control unit (ECU) reads airflow (a manifold pressure or mass airflow sensor), engine speed and crank position, throttle position, coolant and air temperature, and the oxygen sensor in the exhaust. It then sets how long each injector stays open. Sequential systems fire each injector once per cycle, timed to its own cylinder.
How does the ECU work out the injector pulse width?
From the air. In a speed-density system the air mass per cylinder is volumetric efficiency × manifold air density × cylinder volume, and density comes from manifold pressure and temperature. Fuel mass = air ÷ (14.7 λ). The injector delivers a fixed mass per millisecond at its rated pressure, so open time = fuel ÷ flow rate. A dead time of about a millisecond is added because the needle takes time to open. The oxygen sensor then trims the result. Change the load and injector size to see the pulse and its duty cycle move.
What is gasoline direct injection (GDI)?
The injector sits in the combustion chamber and sprays straight into the cylinder at a much higher pressure, about 100 to 350 bar, from a cam-driven high-pressure pump. The evaporating fuel cools the charge, which resists knock and allows a higher compression ratio or more turbo boost, so GDI is common on small turbo petrol engines such as Hyundai's 1.0 T-GDi. The catches are soot particles, now limited by emission norms, carbon deposits on intake valves that no longer get washed by fuel, and cost.
Manifold pressure halves (100 to 50 kPa) at the same λ. The injector pulse width:
The fuel time halves, but the fixed dead time does not: with a 200 cc/min injector the pulse goes from 8.75 ms to 4.88 ms, 56% of the original.
Worked examples
Air, fuel and pulse width at full load · 1.2 L four-cylinder (1,197 cc), manifold 100 kPa and 40 °C, volumetric efficiency 0.85, λ = 1, injector 200 cc/min, petrol 0.745 kg/L, dead time 1.0 ms
- Air density = 100,000 / (287 × 313.15) = 1.1127 kg/m³
- Air per cylinder = 0.85 × 1.1127 × 299.25 cm³ = 283.0 mg
- Fuel = 283.0 / 14.7 = 19.25 mg
- Injector flow = 200 cc/min × 0.745 g/cc = 2.483 g/s
- Pulse = 19.25 mg / 2.483 g/s + 1.0 ms = 8.75 ms
Answer: 283 mg air, 19.3 mg fuel, 8.75 ms
Duty cycle at the rev limit and at idle · Same engine; 6,000 rpm at full load; idle at 40 kPa manifold pressure
- One four-stroke cycle at 6,000 rpm takes 120 / 6,000 s = 20 ms
- Duty = 8.75 / 20 = 43.8%, comfortably below the usual 80 to 85% design ceiling
- Idle: air = 0.4 × 283.0 = 113.2 mg, pulse = 3.10 + 1.0 = 4.10 ms
- At idle the dead time is 24% of the pulse, so its accuracy matters most there
Answer: 44% duty at 6,000 rpm; 4.10 ms at idle
Sizing injectors for an engine · 66 kW at full power, brake specific fuel consumption 0.30 kg/kWh (typical when rich at full load), 4 injectors, 80% maximum duty
- Fuel flow = 66 × 0.30 = 19.8 kg/h; per injector 4.95 kg/h
- = 6.644 L/h = 110.7 cc/min if open all the time
- At 80% duty: 110.7 / 0.8 = 138 cc/min
Answer: about 138 cc/min injectors (the next size up is chosen)
Diesel injection: unit injector, rotary pump and common rail
Which syllabus covers thisAU CME380 Unit IIVTU BME654D Module 1SPPU 402044A Unit 1MU MEDLO7031 Module 1KTU MET352 Module 4
Why does a diesel engine need such high injection pressure?
A diesel has no spark. It compresses air alone, at a compression ratio around 15 to 18 for modern car engines, until the air is hot enough to ignite fuel sprayed into it. The fuel must break into very fine droplets, mix with air and evaporate in a few milliseconds. Higher pressure means a faster jet, finer droplets and better mixing, which gives more complete burning, less soot and more power. That is why injection pressures rose from a few hundred bar in old pumps to over 2,000 bar today.
How does a rotary distributor pump work?
One pump serves every cylinder. A single plunger, driven by a cam plate as the pump turns at half engine speed, both pressurises the fuel and rotates to line up with an outlet for each cylinder in firing order. A control sleeve or solenoid sets how much fuel each stroke delivers, and a timing device advances injection as speed rises. These pumps were compact and cheap and were used on many small diesels, but their pressure depends on engine speed, which limits low-speed refinement and emissions.
What is a unit injector?
A pump and injector combined in one unit at each cylinder, driven directly by a lobe on the overhead camshaft through a rocker. With no high-pressure pipe in between, it reaches very high pressures, around 2,000 bar, and a solenoid valve on each unit sets timing and quantity. Volkswagen's Pumpe-Düse TDI engines used them widely. The drawback is that pressure still follows the cam and engine speed, and multiple injections are hard, so common rail replaced it in cars.
How does common rail direct injection (CRDI) work?
A high-pressure pump keeps a thick-walled rail filled with diesel at a pressure the ECU chooses, from about 300 bar at idle to over 2,000 bar at full load, whatever the engine speed. Short pipes feed solenoid or piezo injectors. Because pressure is always ready, the ECU sets injection timing and quantity freely and can split each cycle's fuel into several injections. Nearly every diesel car and SUV sold in India under BS VI uses common rail, which is why 'CRDi' badges became common.
Why split the fuel into pilot, main and post injections?
A diesel's ignition delay lets fuel pile up before it lights; when it does, pressure rises sharply and you hear the familiar diesel knock. A small pilot injection, one or two cubic millimetres, lights first and warms the chamber, so the main injection burns smoothly and quietly. The main injection makes the torque. A post injection late in the stroke burns leftover soot or, later still, sends fuel to heat the particulate filter for regeneration. The fuel through each hole follows the orifice equation.
Raise the rail pressure from 800 to 1,600 bar with the same nozzle and injection time (60 bar in the cylinder). The fuel injected goes up by about:
Flow goes with the square root of the pressure difference: √(1,540/740) = 1.443, so about 44% more fuel. Higher pressure mainly buys faster jets and finer spray.
Worked examples
Main injection quantity · Rail 1,600 bar, cylinder 60 bar, 7 holes of 0.13 mm, C_d = 0.7, diesel 832 kg/m³, needle fully open for 800 µs
- Jet speed = √(2 × 1,540 × 10⁵ / 832) = 608.4 m/s
- Hole area = 7 × π/4 × 0.13² = 0.0929 mm²
- Flow = 0.7 × 0.0929 mm² × 608.4 m/s = 39.57 mm³/ms
- Volume = 39.57 × 0.8 = 31.66 mm³ = 26.34 mg
Answer: 31.7 mm³ (26.3 mg) per injection
Fuel per stroke for a target power · 1.5 L four-cylinder diesel, 74 kW at 4,000 rpm, BSFC 0.25 kg/kWh (typical at full load); same nozzle at 1,800 bar
- Fuel = 74 × 0.25 = 18.5 kg/h
- Injections per second = 4 × 4,000 / 120 = 133.3
- Per injection = 18.5 / 3,600 / 133.3 = 38.5 mg = 46.3 mm³
- Jet speed at 1,800 bar = 646.7 m/s; time = 46.3 / (0.7 × 0.0929 × 646.7 × 10⁻³) = 1101 µs
Answer: 46 mm³ per stroke, about 1.1 ms of full needle lift
Size of a pilot injection · Same nozzle at 1,600 bar; effective full-open time 50 µs (the electrical pulse is longer because the needle takes time to lift)
- Volume = 39.57 mm³/ms × 0.05 ms = 1.98 mm³
- That is 6% of the 800 µs main injection
- Pilots of about 1 to 2 mm³ are typical: enough to start burning before the main injection arrives
Answer: about 2.0 mm³
Ignition, cooling, lubrication and engine management
Which syllabus covers thisAU CME380 Unit IIVTU BME654D Module 1SPPU 402044A Unit 1MU MEDLO7031 Modules 1-3KTU not in syllabus
What does an ignition coil do, and what is dwell?
A spark plug needs 10,000 to 30,000 volts or more to jump its gap, and the battery gives 12 to 14. The coil is a step-up transformer. While the primary circuit is switched on, current builds up and stores energy in the coil's magnetic field. That switched-on time is the dwell. When the circuit opens, the field collapses and the secondary winding, with about 100 times more turns, delivers the high-voltage spark. The current needs time to build, so a short dwell at high speed means a weaker spark.
How do transistorised and capacitor discharge ignition differ from contact breaker points?
In the old battery system, mechanical contact breaker points switch the coil's primary current. The points arc, wear and drift out of adjustment, and their dwell angle is fixed, so the spark weakens at high speed. Transistorised coil ignition lets a transistor do the switching, triggered by a contactless sensor, and the control module varies the dwell to reach the same current at every speed. Capacitor discharge ignition (CDI) charges a capacitor to a few hundred volts and dumps it into the coil, giving a very fast, strong spark. CDI is common on two-wheelers.
Why does the spark need to fire earlier at high speed and light load?
The flame takes a few milliseconds to burn through the cylinder, and peak pressure should arrive just after top dead centre (TDC). At higher speed the crank turns more degrees in those milliseconds, so the spark must fire earlier: this is speed (centrifugal) advance. At light load the mixture is diluted and burns slowly, so it needs extra advance: this is vacuum advance. Too much advance causes knock, a sharp pressure spike that damages pistons. Modern engines read the best advance from an ECU map and pull it back when a knock sensor hears knocking.
Why does an engine need a cooling system, and what does the thermostat do?
Roughly a quarter to a third of the fuel's energy goes into the cylinder walls and head. Without cooling, the oil film breaks down, pistons seize and the mixture knocks. A water pump pushes coolant (water plus ethylene glycol) through the block and head, then through the radiator. The thermostat stays shut until the engine warms up, around 80 to 90 °C, so a cold engine reaches temperature fast; overcooling wastes fuel and wears bores. The pressure cap raises the boiling point. Small engines and many two-wheelers use air cooling with fins instead.
How is an engine lubricated, and what does an oil grade like 5W-30 mean?
In a pressure-feed system the oil pump draws from the sump through a strainer and sends oil through a filter to galleries drilled to the crankshaft and camshaft bearings. Cylinder walls and the small end get oil by splash and from jets. The oil reduces friction and wear, cools the pistons, seals the rings and carries dirt to the filter. The SAE J300 grade has two parts: 5W is the winter grade, how easily the oil flows when cold; 30 is its viscosity grade at 100 °C. A lower W number means easier cold starts.
What does an engine management system (ECU) read and control?
The engine control unit (ECU) is a small computer. Its inputs are sensors: crankshaft and camshaft position (speed and which cylinder is firing), mass air flow or manifold pressure (how much air is coming in), throttle position, coolant and intake air temperature, the knock sensor and the exhaust oxygen (lambda) sensor. Its outputs are the injector pulse width, the ignition timing and dwell, the idle air or electronic throttle, the variable valve timing and the cooling fan. It runs closed-loop control on the oxygen sensor to hold the mixture where the catalyst works.
A contact breaker system has a fixed dwell angle. On a four-cylinder engine, going from 1,000 to 6,000 rpm, its spark energy:
Dwell time falls from 18 ms to 3 ms, and the coil's time constant is 2.3 ms, so the current reaches only 3.38 A instead of 4.66 A. Energy goes with current squared: 76 mJ falls to 40 mJ.
Worked examples
Spark energy of a contact breaker coil at two speeds · Coil with ballast: V = 14 V, R = 3.0 Ω, L = 7 mH (typical); four-cylinder four-stroke; dwell = 60% of the time between sparks
- Sparks per second at 1,000 rpm: 1000/60 × 4/2 = 33.3, so 30 ms between sparks and 18 ms of dwell
- Time constant L/R = 2.33 ms; i = (14/3)(1 − e^(−18/2.33)) = 4.66 A; E = ½ × 0.007 × 4.66² = 76.2 mJ
- At 6,000 rpm: 5 ms between sparks, 3 ms dwell; i = 4.67(1 − e^(−3/2.33)) = 3.38 A
- E = ½ × 0.007 × 3.38² = 39.9 mJ
Answer: 76 mJ at 1,000 rpm, 40 mJ at 6,000 rpm
Dwell time of an electronic ignition · High-energy coil: R = 0.5 Ω, L = 3 mH, module limits current to 7 A, V = 14 V (typical); four-cylinder at 6,000 rpm
- Solve 7 = (14/0.5)(1 − e^(−t × 0.5/0.003)) for t
- t = −(L/R) ln(1 − IR/V) = −6 ms × ln(1 − 0.25) = 1.73 ms
- Time between sparks at 6,000 rpm = 5 ms = 180 crank degrees, so the dwell is 34.5% of it, 62°
- Stored energy ½ × 0.003 × 7² = 73.5 mJ at every speed
Answer: 1.73 ms of dwell (62° at 6,000 rpm) for 73.5 mJ per spark
Coolant flow through the radiator · Heat into the coolant at full load 50 kW (typical for a 60 kW engine); 8 K temperature drop across the radiator; 50/50 glycol: cp 3.6 kJ/kg K, density 1,070 kg/m³
- Q = ṁ cp ΔT, so ṁ = Q/(cp ΔT)
- ṁ = 50,000/(3,600 × 8) = 1.74 kg/s
- Volume flow = 1.74/1,070 = 1.62 L/s = 97 L/min
Answer: About 97 L/min, the job of the water pump
Turbochargers and superchargers
Which syllabus covers thisAU CME380 Unit IIVTU not in syllabusSPPU not in syllabusMU MEDLO7031 Module 2KTU MET352 Module 4
Why turbocharge or supercharge an engine?
An engine's power is limited by how much air it can swallow, because the fuel needs oxygen to burn. Pushing air in above atmospheric pressure packs more oxygen into the same cylinder, so it can burn more fuel and make more power. That lets a small engine do a big engine's job: many Indian cars now use 1.0 and 1.2 litre turbo-petrol engines where a 1.5 litre was needed before, and almost every modern diesel is turbocharged. A smaller engine has less friction and pumping loss, so it uses less fuel at part load.
How hot does the compressor make the air, and why fit an intercooler?
Compressing air heats it. A real compressor heats it more than the ideal (isentropic) process because of friction, and its isentropic efficiency, typically 65 to 78%, says how much more. Hot air is less dense, which cancels part of the boost, and it makes petrol engines knock. An intercooler is an air-to-air or air-to-water radiator between the compressor and the engine. Its effectiveness is the fraction of the temperature rise it removes. Cooling the charge from 122 °C to 58 °C raises the density gain at 2:1 boost from 1.53 to 1.83 times.
What is the difference between a turbocharger and a supercharger?
A turbocharger uses a turbine in the exhaust to spin a compressor on the same shaft, at up to 200,000 rpm or more in small units. It recovers energy that would leave through the tailpipe, but it needs exhaust flow before it builds boost. A supercharger is driven from the crankshaft by a belt or gears. Roots and twin-screw types are positive displacement and give boost from idle; centrifugal types behave more like a turbo. A supercharger responds instantly but takes shaft power, so it costs more fuel than a turbo for the same boost.
What are wastegate (WGT) and variable geometry (VGT) turbochargers?
A turbo sized to give good boost at low engine speed would over-boost at high speed. A wastegate turbo (WGT) has a valve that lets part of the exhaust bypass the turbine once boost reaches its set value; an actuator opens it on a pressure signal or an ECU command. A variable geometry turbo (VGT, or variable nozzle turbine) instead has movable vanes around the turbine wheel. Closing them at low speed speeds up the exhaust onto the wheel for quick boost; opening them at high speed limits it. VGTs are standard on modern diesels.
What is turbo lag, and how is it reduced?
Turbo lag is the delay between pressing the accelerator and getting boost. At low engine speed there is little exhaust energy, and the rotor has to speed up against its own inertia before the compressor delivers pressure. Ways to cut it: a smaller, lighter turbine wheel; a twin-scroll housing that keeps exhaust pulses from different cylinders apart; a variable geometry turbine; two turbos in sequence, a small one for low speed and a big one for high; and electric assistance, a motor on the shaft or a separate electric compressor.
Air at 30 °C is compressed 2:1 by a 72% efficient compressor, with no intercooler. The air going into the engine is denser than atmospheric air by about:
The air leaves at 122 °C, so density rises by 2 × 303/395 = 1.53, not 2. An intercooler of 70% effectiveness brings it to 1.83.
Worked examples
Charge temperature and density, with and without an intercooler · Pressure ratio 2.0, compressor efficiency 72%, ambient 30 °C (303.15 K), intercooler effectiveness 70%, γ = 1.4, no pressure losses
- Ideal outlet: 303.15 × 2^0.2857 = 369.5 K
- Real outlet: T2 = 303.15 × [1 + (1.2190 − 1)/0.72] = 395.4 K = 122.2 °C
- After the intercooler: T3 = 395.4 − 0.7 × (395.4 − 303.15) = 330.8 K = 57.7 °C
- Density ratio = (p2/p1)(T1/T): hot 1.534, intercooled 1.833
Answer: 1.53 times denser without an intercooler, 1.83 times with one
Power the turbine must supply to the compressor · Same compressor (2:1, 72%, 30 °C); engine air flow 0.08 kg/s; cp = 1,005 J/kg K
- Work per kg = cp (T2 − T1) = 1,005 × (395.4 − 303.15) = 92.7 kJ/kg
- Power = ṁ w = 0.08 × 92.7 = 7.41 kW
Answer: About 7.4 kW, taken from exhaust energy instead of the crankshaft
From a boost gauge reading to the compressor outlet temperature · Boost gauge 0.8 bar at sea level (1.013 bar atmospheric), ambient 25 °C, compressor efficiency 70%
- Absolute boost = 0.8 + 1.013 = 1.813 bar, so the pressure ratio is 1.813/1.013 = 1.790
- Ideal outlet: 298.15 × 1.790^0.2857 = 352.1 K = 78.9 °C
- Real outlet: 298.15 + (352.1 − 298.15)/0.70 = 375.2 K = 102.1 °C
Answer: Pressure ratio 1.79; the air leaves the compressor at about 102 °C
Emissions, catalytic converters and BS VI norms
Which syllabus covers thisAU CME380 Unit IIVTU BME654D Module 4SPPU not in syllabusMU MEDLO7031 Module 3KTU not in syllabus
What comes out of an engine's exhaust, and why is it harmful?
Mostly nitrogen, carbon dioxide and water, which are the products of complete combustion. The regulated pollutants are small fractions. Carbon monoxide (CO) is poisonous because it binds to blood in place of oxygen. Unburnt hydrocarbons (HC) and nitrogen oxides (NOx) react in sunlight to form smog and ground-level ozone; NOx also causes acid rain and lung damage. Particulate matter (PM), the soot from diesels and direct-injection petrol engines, lodges deep in the lungs. CO2 is not toxic but is the main greenhouse gas, so fuel economy is regulated too.
How do CO, HC, NOx and soot form in an engine?
CO forms when there is not enough oxygen to finish burning carbon to CO2, so it follows the mixture: high when rich, near zero when lean. HC comes from fuel that escapes the flame: in crevices around the piston rings, in the cold layer next to the walls where the flame quenches, absorbed in the oil film, or from misfires. NOx forms when nitrogen and oxygen from the air combine at the highest flame temperatures, above about 1,800 K, so it peaks slightly lean of stoichiometric. Soot forms in fuel-rich pockets inside a diesel spray.
What is lambda, and how does the exhaust change with it?
Lambda (λ) is the actual air-fuel ratio divided by the stoichiometric one, the exact amount of air needed to burn all the fuel. For petrol that is about 14.6 kg of air per kg of fuel. At λ = 1 the exhaust has no spare oxygen and almost no CO. Richer (λ < 1), oxygen runs out, and CO and hydrogen appear. Leaner (λ > 1), the spare oxygen shows up in the exhaust. A lambda (oxygen) sensor reads that oxygen, and the ECU trims the injection to hold λ close to 1.
How does a three-way catalytic converter work?
It is a ceramic or metal honeycomb with thousands of fine channels, coated with a washcoat that carries platinum, palladium and rhodium. Platinum and palladium oxidise CO to CO2 and HC to CO2 and water. Rhodium reduces NOx to nitrogen, using the CO and hydrogen as the reducing agents. That is why it works on all three only in a narrow band around λ = 1: rich, there is not enough oxygen to clean up CO and HC; lean, NOx passes straight through. Cerium oxide in the coating stores oxygen to smooth out small swings. It needs about 250 to 300 °C to light off.
How do diesel engines meet BS VI: EGR, DPF and SCR?
A diesel always runs lean, so a three-way catalyst cannot reduce its NOx. Exhaust gas recirculation (EGR) sends some cooled exhaust back into the intake; the inert gas lowers the flame temperature and NOx. A diesel oxidation catalyst (DOC) burns CO and HC. A diesel particulate filter (DPF) traps soot in porous walls and burns it off periodically, called regeneration. Selective catalytic reduction (SCR) sprays urea solution (AdBlue, diesel exhaust fluid) into the exhaust, which turns into ammonia and converts NOx into nitrogen and water.
What are India's BS VI emission limits for cars?
Bharat Stage VI, notified by the Ministry of Road Transport and Highways in 2016, applied to all new vehicles from 1 April 2020; India skipped BS V. For passenger cars its limits match Euro 6. Petrol: CO 1.0 g/km, total HC 0.10, non-methane HC 0.068, NOx 0.060. Diesel: CO 0.50, HC + NOx 0.170, NOx 0.080. Particulate mass is 0.0045 g/km for diesels and direct-injection petrol engines. BS VI phase 2 (from April 2023) added real driving emission checks with portable equipment on the road, not just on the test bench.
A petrol engine runs 10% rich (λ = 0.9) instead of at λ = 1. The carbon monoxide in its dry exhaust goes from almost zero to about:
With 10% too little air, about a quarter of the carbon cannot reach CO2. The water-gas equilibrium splits the shortage between CO and H2: 3.7% CO and 1.2% H2 in the dry exhaust, against 12.8% CO2.
Worked examples
Stoichiometric air-fuel ratio and lambda · Petrol modelled as CH1.87 (Heywood); air = O2 + 3.773 N2; molar masses C 12.011, H 1.008, O2 31.998, N2 (atmospheric) 28.16; measured air-fuel ratio 13.5
- CH1.87 + (1 + 1.87/4)(O2 + 3.773 N2) → CO2 + 0.935 H2O + 3.773 × 1.4675 N2
- Air per mole of fuel = 1.4675 × (31.998 + 3.773 × 28.16) = 202.9 g; fuel = 12.011 + 1.87 × 1.008 = 13.90 g
- (A/F)s = 202.9/13.90 = 14.60
- λ = 13.5/14.60 = 0.925: about 7.5% rich
Answer: (A/F)s = 14.6; the engine is running at λ = 0.925
Dry exhaust composition 10% rich and 10% lean · CH1.87 at λ = 0.9 and λ = 1.1; lean: complete combustion; rich: water-gas equilibrium K = (CO·H2O)/(CO2·H2) = 3.5; water removed before analysis
- Lean λ = 1.1: CO2 = 1, H2O = 0.935, O2 = 0.1 × 1.4675 = 0.147, N2 = 3.773 × 1.1 × 1.4675 = 6.091 mol
- Dry total = 1 + 0.147 + 6.091 = 7.238 → CO2 13.82%, O2 2.03%
- Rich λ = 0.9: O available = 2 × 0.9 × 1.4675 = 2.6415; C, H, O balances plus K = 3.5 give one quadratic in CO
- Solving: CO 3.68%, CO2 12.84%, H2 1.17% (dry)
Answer: λ 1.1: 13.8% CO2, 2.0% O2; λ 0.9: 12.8% CO2, 3.7% CO, 1.2% H2
Does this petrol car pass BS VI? · Type-test results: CO 0.42, THC 0.06, NMHC 0.05, NOx 0.07 g/km; BS VI petrol limits CO 1.0, THC 0.10, NMHC 0.068, NOx 0.060 g/km
- CO 0.42 ≤ 1.0: pass
- THC 0.06 ≤ 0.10 and NMHC 0.05 ≤ 0.068: pass
- NOx 0.07 > 0.060: fail, 16.7% over the limit
Answer: It fails on NOx; a richer-biased λ control or a better catalyst would be the first fixes to try
Clutches and the fluid flywheel
Which syllabus covers thisAU CME380 Unit IIIVTU BME654D Module 2SPPU not in syllabusMU not in syllabusKTU MET352 Module 1
Why does a car need a clutch?
A petrol or diesel engine cannot make torque below its idle speed, about 700 to 900 rpm, so it cannot be bolted straight to wheels that start from zero. The clutch lets the engine run while the car stands still, then takes up the drive gradually by slipping until both sides turn together. It also disconnects the engine for a moment so you can change gear without grinding, and it slips instead of breaking parts if the driver drops the pedal suddenly. Its main parts are the flywheel, the clutch plate and the pressure plate.
How much torque can a friction clutch carry?
The spring squeezes the friction plate with an axial force W. Friction at each contact surface gives a tangential force μW acting at an effective friction radius R_m, so the torque is μ W R_m for every friction surface. A single plate has two surfaces, one against the flywheel and one against the pressure plate. A new plate presses evenly (uniform pressure). After running in, the outer edge, which slides faster, wears more until the wear rate is even (uniform wear), which gives a slightly smaller R_m. Designers use the uniform wear value because it is the safe one.
How does a single-plate diaphragm spring clutch work?
The clutch plate, splined to the gearbox input shaft, sits between the flywheel and the pressure plate. A diaphragm spring, a dished steel disc with radial fingers, presses the pressure plate against the plate. Pressing the pedal moves the release bearing against the fingers; the diaphragm pivots like a lever and lifts the pressure plate off. In a push type the bearing pushes the fingers; in a pull type it pulls them, which allows a bigger spring. Unlike coil springs, the diaphragm's force barely drops as the lining wears. Small coil springs in the plate hub damp engine vibration.
Where are multi-plate, wet, centrifugal and electromagnetic clutches used?
A multi-plate clutch stacks several friction and steel plates, so it carries more torque in a small diameter; motorcycles and automatic gearboxes use it. A wet clutch runs in oil, which cools it and makes engagement smooth but lowers μ to about 0.1, so it needs more plates. A centrifugal clutch engages by itself as engine speed rises, when weighted shoes fly outward against a drum; scooters with CVTs use it. An electromagnetic clutch is pulled together by a coil, as in a car's air-conditioning compressor, so the ECU can switch it on and off.
How does a fluid flywheel (fluid coupling) transmit power?
It has two bowl-shaped halves with radial vanes, facing each other inside an oil-filled casing. The impeller is driven by the engine; it flings oil outward and across into the runner, which drives the gearbox. Oil keeps circulating as long as the impeller is faster. At idle the slip is large, so the car can stand in gear without stalling; at cruising speed the slip is typically 2 to 3%. With no fixed reaction member, output torque equals input torque, so its efficiency equals the speed ratio. A torque converter adds a stator to multiply torque.
Keeping the same spring force and facing size, you change a single-plate clutch to a twin-plate one. Its torque capacity:
A twin-plate clutch has 4 friction surfaces instead of 2, and each carries μ W R_m with the same squeezing force passing through the whole stack. That is why heavy vehicles and racing cars use multi-plate clutches.
Worked examples
Torque capacity of a car's single-plate clutch · Facing r1 = 110 mm, r2 = 75 mm; spring force W = 4 kN; μ = 0.3 (dry organic lining); engine torque 113 N·m
- Uniform wear: R_m = (110 + 75)/2 = 92.5 mm; T = 0.3 × 4,000 × 0.0925 × 2 = 222 N·m
- Uniform pressure: R_m = ⅔ (110³ − 75³)/(110² − 75²) = 93.6 mm; T = 224.6 N·m
- Margin over the engine: 222/113 = 1.96
Answer: 222 N·m (uniform wear, the design value), about 2.0 times the engine torque
Spring force needed for a diesel SUV clutch · Engine torque 200 N·m, design factor 1.3; single plate, r1 = 125 mm, r2 = 80 mm, μ = 0.3; uniform wear
- Design torque = 200 × 1.3 = 260 N·m
- R_m = (125 + 80)/2 = 102.5 mm; W = T/(μ R_m n) = 260/(0.3 × 0.1025 × 2) = 4,228 N
- Maximum pressure (at r2): p = W/(2π r2 (r1 − r2)) = 4,228/(2π × 0.08 × 0.045) = 187 kPa
Answer: About 4.23 kN of clamp force; peak lining pressure 187 kPa at the inner edge
Wet multi-plate clutch of a motorcycle · 11 plates: 6 tabbed to the clutch basket and 5 splined to the hub, alternating; facing r1 = 62 mm, r2 = 48 mm; spring force 1.2 kN; μ = 0.12 in oil; uniform wear
- Friction surfaces n = n1 + n2 − 1 = 6 + 5 − 1 = 10
- R_m = (62 + 48)/2 = 55 mm
- T = 0.12 × 1,200 × 0.055 × 10 = 79.2 N·m
Answer: 79 N·m: ten surfaces make up for the low friction of a wet clutch
Manual gearboxes and gear ratios
Which syllabus covers thisAU CME380 Unit IIIVTU BME654D Module 2SPPU not in syllabusMU not in syllabusKTU MET352 Module 1
Why does a car need a gearbox?
An engine makes useful torque only between about 1,000 and 6,000 rpm, and its torque barely changes in that band. A car needs a huge pull at the wheels to start on a slope, and a small pull at high speed. With one fixed ratio you could have either good starting or a decent top speed, not both. The gearbox gives several ratios: a low gear multiplies torque for starting and climbing, a high gear lets the engine turn slowly at highway speed. The power stays the same; the gearbox trades speed for force.
What is a tractive effort diagram, and how do you read it?
It plots the pulling force at the driving wheels against road speed, one curve per gear, and the road resistance on the same axes. Tractive force is engine torque times the gear ratio and final drive ratio, times driveline efficiency, divided by the wheel radius. Resistance is rolling resistance, plus the gradient, plus aerodynamic drag, which grows with speed squared. The gap between a gear's curve and the resistance is the force left to accelerate. Where the top gear curve crosses resistance is the top speed; the peak of first gear sets the steepest hill you can climb.
What are sliding mesh, constant mesh and synchromesh gearboxes?
In a sliding mesh gearbox, the oldest type, spur gears on the main shaft slide along splines to mesh with gears on the layshaft. The driver must match speeds by double declutching, or the teeth grind. In a constant mesh gearbox all gear pairs are always meshed, usually helical and quieter; the gears spin freely on the main shaft and a sliding dog clutch locks the chosen one to it. A synchromesh gearbox is a constant mesh box with a small cone clutch on each dog clutch that matches speeds first. Every modern manual car uses synchromesh.
How does a synchroniser match speeds before a gear engages?
When you move the lever, the shift fork pushes a sleeve towards the gear. First a brass blocker ring with an internal cone touches a matching cone on the gear. Friction between the cones speeds up or slows down the gear until it turns at the same speed as the main shaft. While the speeds differ, the friction torque holds the blocker ring's teeth slightly out of line, so the sleeve cannot pass. Once the speeds match, the ring turns back, the sleeve slides over the dog teeth, and the gear is locked to the shaft with no clash.
How are a car's gear ratios chosen?
First gear is set by the steepest gradient or trailer the car must start on, and by the grip of the tyres. Top gear is set by the top speed or, in a fifth gear used as an overdrive, by low engine speed for economy on the highway. The gears in between are spread so the engine drops back to the same speed after each upshift, a geometric progression where each ratio is the one below divided by a constant step. Real gearboxes close the upper steps a little, because at speed a big drop in engine speed is felt more.
A typical 1.2 litre hatchback (113 N·m, five speeds, final drive 4.1) reaches its top speed in which gear?
Fifth is an overdrive (0.725): it keeps the engine slow at 100 km/h to save fuel, but its tractive force falls below the road load earlier. In 4th the car reaches about 180 km/h near the 6,000 rpm limit. Drag that grows with speed squared decides it.
Worked examples
Road speed in each gear at 6,000 rpm · Ratios 3.545, 1.904, 1.233, 0.911, 0.725 (typical five-speed); final drive 4.1; rolling radius 0.3 m
- v = 2π r N / (60 i_g i_0) = 2π × 0.3 × 6,000/(60 × i_g × 4.1) m/s
- 1st 46.7, 2nd 86.9, 3rd 134.2 km/h
- 4th 181.7, 5th 228.3 km/h (5th is never reached at 6,000 rpm: drag stops the car first)
Answer: 47, 87, 134, 182, 228 km/h
Tractive force and steepest climb in first gear · Peak torque 113 N·m at 4,200 rpm; 1st 3.545, final drive 4.1, efficiency 0.9, r = 0.3 m; mass 1,000 kg, Cr = 0.012, Cd·A = 0.32 × 2.1 m², air 1.2 kg/m³
- F = 113 × 3.545 × 4.1 × 0.9/0.3 = 4,927 N
- Speed at 4,200 rpm in 1st = 32.7 km/h, where drag is only 33 N
- Climbing: m g (Cr cos θ + sin θ) = 4,894 N → sin(θ + 0.69°) = 0.4988, θ = 29.2°
- Gradient tan θ = 56.0%
Answer: 4,927 N at the wheels; it could climb a 56% slope if the tyres grip
Geometric progression against real ratios · Five gears from 3.545 down to 0.725
- Step k = (3.545/0.725)^(1/4) = 1.487
- Geometric set: 3.545, 2.384, 1.603, 1.078, 0.725
- Real steps: 1-2 1.86, 2-3 1.54, 3-4 1.35, 4-5 1.26
Answer: The real gearbox uses big steps low down and closer ones at the top (progressive spacing), so upshifts at speed drop the engine less
Automatic transmissions: epicyclic gears, torque converter, AMT and CVT
Which syllabus covers thisAU CME380 Unit IIIVTU BME654D Module 2SPPU not in syllabusMU not in syllabusKTU MET352 Module 1
How does one epicyclic (planetary) gear set give several ratios?
It has a sun gear in the middle, planet gears around it carried on an arm called the carrier, and a ring gear with internal teeth around the planets. All gears stay in mesh. Hold one member still, drive another, and take the output from the third. Holding the ring and driving the sun gives a big reduction at the carrier. Holding the sun and driving the carrier makes the ring turn faster, an overdrive. Holding the carrier reverses the ring. Locking any two together turns the whole set as one, direct drive.
How does a conventional automatic gearbox change gear without a clutch pedal?
It uses two or more planetary gear sets, often combined as a Simpson or Ravigneaux set, whose members can be held or joined by multi-plate clutches and band brakes. Each gear is a different combination of members held and driven. Hydraulic pressure, controlled by a valve body and today by an electronic transmission control unit, applies one clutch while releasing another, so the shift happens under load without interrupting the drive. A torque converter between the engine and the gearbox lets the car creep and stop in gear.
How does a torque converter multiply torque?
It is a fluid coupling with a third member, the stator, between the turbine's outlet and the impeller's inlet. The stator redirects the oil leaving the turbine so it helps the impeller instead of opposing it. The stator's reaction adds to the output torque, so at stall (turbine stopped) the turbine torque is typically about two to two and a half times the engine torque. As the turbine speeds up, the multiplication falls; at the coupling point the stator starts freewheeling on its one-way clutch. A lock-up clutch then joins the impeller and turbine to stop slip losses.
How do AMT, CVT, DCT and IMT differ?
An automated manual transmission (AMT) is an ordinary manual gearbox and clutch worked by electro-hydraulic actuators; it is cheap, which is why many Indian small cars use it, but the drive pauses during each shift. A continuously variable transmission (CVT) runs a steel belt between two pulleys whose effective diameters change, giving any ratio in its range. A dual-clutch transmission (DCT) has two clutches, one for the odd and one for the even gears, so the next gear is ready before the shift. An intelligent manual transmission (IMT) keeps the gear lever but has no clutch pedal; a sensor in the lever triggers an actuator.
What is an overdrive, and what is an infinitely variable transmission (IVT)?
An overdrive is any ratio below 1:1, so the output shaft turns faster than the engine. It lowers engine speed at cruising speed, cutting fuel use and noise; in an epicyclic overdrive the sun is held and the carrier drives the ring. An infinitely variable transmission goes one step beyond a CVT: by combining a variator with a planetary set, its output can be brought all the way down to zero speed (geared neutral) while the engine keeps running, so the car can start without any clutch at all.
A planetary set has a 30-tooth sun, 18-tooth planets and a 66-tooth ring. Hold the ring and drive the sun at 1,000 rpm. The carrier turns:
With the ring held, ratio = 1 + zr/zs = 1 + 66/30 = 3.2, so the carrier turns at 1,000/3.2 = 312.5 rpm the same way. This is the classic low gear of an automatic.
Worked examples
Three ratios from one planetary set · Sun 30 teeth, planets 18 teeth, so ring = 30 + 2 × 18 = 66 teeth; 3 planets fit evenly because (30 + 66)/3 = 32
- Ring held, sun in, carrier out: 1 + 66/30 = 3.20 (reduction)
- Sun held, carrier in, ring out: 66/(30 + 66) = 0.6875, so 1,000 rpm in gives 1,454.5 rpm (overdrive)
- Carrier held, sun in, ring out: −66/30 = -2.2 (reverse)
Answer: 3.2 : 1 low, 0.688 : 1 overdrive and 2.2 : 1 reverse
Planet speed by the tabular method · Sun 24, planets 24, ring 72 teeth; ring held; sun driven at 3,000 rpm
- Step 1, carrier fixed, sun +x: planet −x × 24/24, ring −x × 24/72
- Step 2, add y to every member. Ring held: −x/3 + y = 0. Sun: x + y = 3,000
- x = 2250, y = 750, so the carrier turns at 750 rpm
- Planet (absolute) = −x + y = -1500 rpm: it spins backwards while its centre goes round forwards
Answer: Carrier 750 rpm (ratio 4 : 1), planets -1500 rpm
Torque converter output at stall and at speed · Engine torque 150 N·m; typical stall torque ratio 2.2; at speed ratio 0.6 the torque ratio is 1.4
- At stall (turbine held by the brakes): turbine torque = 150 × 2.2 = 330 N·m
- At speed ratio 0.6: efficiency = torque ratio × speed ratio = 1.4 × 0.6 = 0.84
- Near the coupling point the torque ratio reaches 1 and efficiency equals the speed ratio, as in a fluid flywheel
Answer: 330 N·m at stall; 84% efficient at a speed ratio of 0.6
Propeller shaft, universal joints, differential and rear axle
Which syllabus covers thisAU CME380 Unit IIIVTU BME654D Module 2SPPU 402044A Unit 2MU not in syllabusKTU not in syllabus
What does the propeller shaft do, and why is it a hollow tube with a slip joint?
In a front-engine, rear-wheel-drive car or truck, the propeller shaft carries the drive from the gearbox to the final drive on the rear axle. The axle moves up and down on its springs, so the shaft's angle and length keep changing: universal joints let the angle change, and a splined slip joint lets the length change. A hollow tube is far stiffer for its weight than a solid bar. Stiffness matters because a long, thin shaft whirls violently at its critical speed, which must stay well above the highest speed it turns at.
Why does a single universal joint make the output speed fluctuate?
A Hooke's (Cardan) joint is two yokes joined by a cross. When the shafts are at an angle β, the output shaft speeds up and slows down twice per revolution even though the input turns steadily; it averages out to the input speed. The swing grows quickly with the angle: about ±3.5% at 15°. Two joints at equal angles, with the yokes on the intermediate shaft in the same plane, cancel each other. Constant velocity (CV) joints, used in front-wheel-drive shafts, avoid the problem altogether.
Why does a car need a differential, and how does it work?
On a turn the outer wheel travels a bigger arc than the inner one, so it must turn faster. With a solid axle one tyre would have to scrub. The differential's cage carries the crown wheel, driven by the pinion on the propeller shaft, plus small bevel planet gears meshing with a sun gear on each half shaft. Going straight, the planets do not spin and both wheels turn with the cage. On a turn the planets spin, so one side speeds up exactly as much as the other slows down. The cage always turns at the average of the two wheels.
What are bevel, hypoid and worm final drives?
The final drive turns the drive through 90° and gives the last big reduction, typically 3.5 to 4.5 for cars and more for trucks. A spiral bevel pair has the pinion axis meeting the crown wheel axis. A hypoid pair offsets the pinion below the crown wheel centre, which lowers the propeller shaft and the floor, and gives larger, stronger, quieter teeth; the sliding between its teeth needs extreme-pressure gear oil. A worm and wheel gives a very large reduction in one step and is used in some heavy trucks.
What are Hotchkiss drive and torque tube drive?
Both are ways of taking the driving thrust and the torque reaction of a live rear axle to the body. In a Hotchkiss drive the leaf springs do it: they push the car along and stop the axle housing from rotating. Because the axle moves on the springs, the open propeller shaft needs two universal joints and a slip joint. In a torque tube drive the propeller shaft runs inside a rigid tube fixed to the axle housing and pivoted near the gearbox, so the tube takes the thrust and torque and only one universal joint is needed. Coil springs can then be used.
What are semi-floating, three-quarter floating and fully floating rear axles?
They differ in what loads the half shaft carries. In a semi-floating axle the wheel is mounted on the end of the half shaft with one bearing between the shaft and the housing, so the shaft carries the car's weight in bending as well as the driving torque; most cars use it. In a three-quarter floating axle the bearing sits between the hub and the housing, so the shaft mainly carries torque and some end thrust. In a fully floating axle the hub runs on two bearings on the housing, and the shaft carries only torque; trucks use it.
A single Hooke's joint runs with its shafts at 20°. Over one revolution the output speed swings between about:
The extremes are cos β and 1/cos β: cos 20° = 0.940 and 1/cos 20° = 1.064. The average over a turn is exactly the input speed.
Worked examples
Speed fluctuation of a single universal joint · Propeller shaft at 2,000 rpm; shaft angle β = 15°
- Maximum output speed = 2,000/cos 15° = 2,070.6 rpm
- Minimum output speed = 2,000 × cos 15° = 1,931.9 rpm
- Fluctuation = ±(1/cos β − cos β)/2 = ±3.47%, twice per revolution
Answer: 1,932 to 2,071 rpm (±3.5%)
Wheel and crown wheel speeds on a turn · Rear axle centre on a 10 m radius; track 1.5 m; 20 km/h; rolling radius 0.3 m; final drive 4.1
- Yaw rate = v/R = 5.556/10 = 0.5556 rad/s
- Inner wheel: 0.5556 × 9.25 = 5.139 m/s → 163.6 rpm; outer: 0.5556 × 10.75 = 5.972 m/s → 190.1 rpm
- Crown wheel (cage) = (163.6 + 190.1)/2 = 176.8 rpm; propeller shaft = 4.1 × 176.8 = 725 rpm
- Difference = (outer − inner)/cage = 1.5/10 = 0.15
Answer: Inner 164 rpm, outer 190 rpm, cage 177 rpm
Whirling (critical) speed of a propeller shaft · Steel tube 63.5 mm outside, 2 mm wall; E = 207 GPa, density 7,850 kg/m³; simply supported; car's top shaft speed 5,500 rpm
- ω_c = (π/L)² √(EI/(ρA)), and for a tube EI/(ρA) = E (d_o² + d_i²)/(16 ρ)
- One piece, L = 1.5 m: N_c = 4,679 rpm, below 5,500 rpm, so it would whirl
- Two pieces of 0.8 m with a centre bearing: N_c = 16,451 rpm
Answer: Split the shaft (or use a larger diameter): 4,679 rpm rises to 16,451 rpm
Steering geometry, steering gears and power steering
Which syllabus covers thisAU CME380 Unit IVVTU BME654D Module 3SPPU 402044A Unit 2MU not in syllabusKTU MET352 Module 4
What does a steering system have to do?
Turn the front wheels by the right amount for the driver's input, with little effort at parking speed and enough feel at highway speed. It must make every wheel roll on a circle around one common centre so the tyres do not scrub, return to straight ahead by itself when you let go, and pass as little road shock back to the hands as possible. A typical car needs about 2.5 to 3.5 turns of the steering wheel from full left to full right.
What is Ackermann steering?
On a turn the inner front wheel follows a tighter circle than the outer one, so it must turn through a bigger angle. Ackermann geometry sets the two angles so that lines drawn square to each front wheel meet on the extended rear axle, at the turn centre. A trapezoidal linkage gets close: the steering arms lean inward so their lines meet near the rear axle. It is exact at one or two angles and a degree or so off elsewhere. Drag the inner angle and watch the error.
What are camber, caster, kingpin inclination and toe?
Camber is the wheel's tilt seen from the front (negative when the top leans in); a little negative camber helps cornering grip. Caster is the backward tilt of the steering axis seen from the side; like a shopping trolley wheel, it pulls the wheels straight after a turn. Kingpin inclination tilts the steering axis inward, which reduces the scrub radius and also helps self-centring. Toe-in or toe-out is how much the fronts of the wheels point towards or away from each other, a millimetre or two, set for straight running and tyre wear.
What are understeer and oversteer?
At speed the tyres corner with a small slip angle, and the car needs more or less steering than the low-speed Ackermann angle. If the front tyres slip more than the rears, you need more steer as speed rises: understeer, which is stable and what makers design for. If the rears slip more, you need less: oversteer, and above a critical speed the car spins. The understeer gradient K compares each axle's load with its tyres' cornering stiffness. Try moving weight forward.
Which steering gearboxes are used, and why power steering?
Most cars use rack and pinion: a pinion on the steering column moves a toothed rack sideways, which pushes the tie rods. It is light, direct and cheap. Trucks and older SUVs use a recirculating ball box, where balls roll between a worm and a nut to cut friction, or a worm and roller. Power steering adds force: hydraulic systems use an engine-driven pump, and electric power steering (EPS) uses a motor on the column or rack, which draws power only when you steer and saves fuel.
A car has 62% of its weight on the front axle and the same tyres all round. On a fixed circle, as speed rises the driver must:
With equal tyres, the heavier front axle needs more slip angle for its share of the cornering force, so K is positive (understeer) and the steer angle grows with speed.
Worked examples
Correct outer angle and turning radius · Wheelbase L = 2.5 m, kingpin track t = 1.4 m, inner wheel turned 35°
- cot δo = cot 35° + t/L = 1.4281 + 0.56 = 1.9881
- δo = 26.70°, about 8.3° less than the inner wheel
- Turn radius to the rear-axle centre: L/tan δi + t/2 = 3.570 + 0.70 = 4.27 m
- Outer front kingpin's circle: L/sin δo = 2.5/0.4493 = 5.56 m (add the scrub radius for the kerb-to-kerb turning circle)
Answer: δo = 26.7°, R = 4.27 m, outer kingpin on a 5.56 m radius
Understeer gradient and characteristic speed · 1,400 kg car, 60% on the front axle, wheelbase 2.6 m, cornering stiffness 1,000 N/° per tyre front and rear; a 100 m corner at 80 km/h
- Axle loads: Wf = 8,240 N, Wr = 5,494 N; axle stiffness 2 × 1,000 = 2,000 N/°
- K = 8,240/2,000 − 5,494/2,000 = 4.120 − 2.747 = 1.37 °/g (understeer)
- Characteristic speed √(57.3 L g / K) = 32.6 m/s = 117 km/h: there the car needs twice the Ackermann angle
- At 80 km/h on 100 m: ay = 22.22²/100 = 0.503 g; δ = 57.3 × 2.6/100 + 1.37 × 0.503 = 1.49° + 0.69° = 2.18°
Answer: K = 1.37 °/g, characteristic speed 117 km/h, 2.18° of road-wheel steer
Overall steering ratio · Steering wheel 2.8 turns lock to lock; road wheels 35° each side of straight ahead
- Steering wheel from centre to full lock: 2.8 × 360°/2 = 504°
- Ratio = 504° ÷ 35° = 14.4 : 1
Answer: About 14.4 : 1, typical of a car with power steering
Suspension systems, springs and dampers
Which syllabus covers thisAU CME380 Unit IVVTU BME654D Module 3SPPU 402044A Unit 3MU not in syllabusKTU MET352 Module 2
What does a suspension do?
It lets each wheel follow the road while the body glides over it. It isolates passengers from bumps (ride), keeps the tyres pressed on the road so they can brake and corner (road holding), and controls how the body pitches and rolls. Everything carried by the springs is sprung mass: body, engine, passengers. The wheels, brakes and part of the links are unsprung mass. Keeping unsprung mass low lets the wheel react quickly without shaking the body.
Why does ride frequency matter?
The body bouncing on its springs is a mass on a spring, with a natural frequency. People find about 1 to 1.5 Hz comfortable, close to walking pace, so most cars are tuned there and sports cars go higher. The tyre is a stiff spring in series with the suspension spring, so the ride rate is a little lower than the spring rate. The wheel's own bounce, wheel hop, sits near 10 to 15 Hz. Change the mass, spring and damping and drive over a speed hump.
What are the main suspension types?
A rigid beam axle on leaf springs is strong and simple, so trucks, buses and many pickups use it, but a bump on one wheel tilts the other. Independent suspensions let each wheel move alone. MacPherson strut, where the damper is also a steering pivot, is on the front of most Indian cars. Double wishbones control camber better and suit SUVs and sports cars. At the rear, hatchbacks often use a twist beam; trailing and semi-trailing arms, multi-link and the De Dion axle are other layouts.
What do springs and dampers each do?
Springs carry the weight and store energy when the wheel rises: leaf springs (which also locate the axle), coil springs, torsion bars, rubber, air springs and hydropneumatic units that can keep the ride height constant. Dampers, often called shock absorbers, push oil through small valves and turn the bounce energy into heat, so the body settles instead of bouncing on. Cars use a damping ratio of roughly 0.2 to 0.4 (typical); higher feels harsh, lower feels floaty.
What are the roll centre, roll axis and body roll?
In a corner the body leans outward. Each axle's linkage sets a roll centre, the point the body rotates about at that axle, and the line joining the front and rear roll centres is the roll axis. The cornering force acts at the centre of gravity, above the roll axis, so it makes a roll couple: mass × lateral acceleration × that height. The springs and anti-roll bars resist with roll stiffness. A stiffer anti-roll bar or a higher roll axis means less lean.
You load 150 kg of luggage into the boot. The springs are unchanged. The rear ride frequency:
Frequency goes as √(k/m). More mass on the same spring bounces more slowly, which is why some cars use self-levelling or progressive springs.
Worked examples
Ride rate, ride frequency and wheel hop · One corner: sprung mass 350 kg, spring rate 25 kN/m, tyre 200 kN/m (typical), unsprung mass 40 kg
- Ride rate KR = ks kt/(ks + kt) = 25 × 200/225 = 22.22 kN/m
- Ride frequency = (1/2π)√(22,222/350) = 1.27 Hz (spring alone would give 1.35 Hz)
- Wheel hop = (1/2π)√((ks + kt)/mu) = (1/2π)√(225,000/40) = 11.9 Hz
Answer: 1.27 Hz body bounce, 11.9 Hz wheel hop
Damper coefficient for a target damping ratio · Same corner, target ζ = 0.3
- Critical damping 2√(k m) = 2√(25,000 × 350) = 5916 N·s/m
- c = ζ × critical = 0.3 × 5916 = 1775 N·s/m
- Damped frequency on the spring: 1.345 × √(1 − 0.3²) = 1.28 Hz
Answer: c ≈ 1775 N·s/m
Body roll in a steady corner · Sprung mass 1,200 kg, CG 0.4 m above the roll axis, lateral acceleration 0.5 g, total roll stiffness 60,000 N·m/rad (springs + anti-roll bars)
- Roll couple = m ay h' = 1,200 × 0.5 × 9.81 × 0.4 = 2,354.4 N·m
- As the body leans its weight adds m g h' φ, so φ = M/(Kφ − m g h') = 2,354.4/(60,000 − 4,708.8)
- φ = 0.0426 rad = 2.44°, a roll gradient of 4.9°/g
Answer: About 2.4° of roll
Brakes: drum, disc, hydraulic and air
Which syllabus covers thisAU CME380 Unit IVVTU BME654D Module 3SPPU 402044A Unit 3MU not in syllabusKTU MET352 Module 3
How does a brake stop a car?
By friction. A stationary lining or pad is pressed against a drum or disc that turns with the wheel, and the car's kinetic energy, half × mass × speed squared, becomes heat in the rubbing parts. Doubling the speed means four times the energy to get rid of. A 1,300 kg car stopping from 100 km/h makes about half a megajoule of heat in a few seconds, so brakes must also shed that heat without fading.
Drum or disc brakes: what is the difference?
In a drum brake two curved shoes inside a drum are pushed outward against it. Drums are cheap, enclosed and easy to fit with a parking brake, so many small cars use them at the rear. In a disc brake a caliper squeezes two pads onto a disc open to the air. Discs cool faster, shed water, resist fade and are easy to inspect, so nearly every car has them at the front, where 60 to 75% of the braking happens.
How does a drum brake's leading shoe help itself?
Each shoe pivots at one end and is pushed at the other. On the leading shoe the drum's rotation drags the lining into the drum, so friction adds to the push and the pressure rises: it is self-energising. On the trailing shoe friction pushes the shoe away, so it gives much less torque for the same force. Two-leading-shoe brakes put a cylinder at each shoe's end to make both lead going forward. Change μ and see the leading shoe pull ahead.
How do hydraulic brakes multiply pedal force?
The pedal is a lever, typically 3 to 5 to 1. A vacuum booster (servo) using engine vacuum, or a pump in hybrids and EVs, multiplies that again. The push rod drives a piston in the master cylinder, and brake fluid carries the pressure to every caliper and wheel cylinder. Pressure is the same everywhere, so a large caliper piston gets a large force. Cars use two separate circuits, often split diagonally, so one leak cannot take away all the brakes.
How do air brakes on trucks and buses work?
An engine-driven compressor fills reservoirs to about 8 to 10 bar. Pressing the pedal opens a valve that sends air to brake chambers, whose diaphragms turn the S-cam or push the disc caliper. Air is free and a leak does not drain a fluid, so it suits heavy vehicles. Parking and emergency braking use strong springs held off by air pressure: if the air is lost, the springs put the brakes on, which makes the system fail-safe.
What makes a good brake lining or pad material?
A friction coefficient of roughly 0.3 to 0.45 that stays steady when hot, wet or new; slow wear; no damage to the drum or disc; little noise and dust; and strength at a few hundred degrees. Asbestos was used for decades and is now banned. Today's pads are organic (non-asbestos organic), semi-metallic with steel fibres, or ceramic. When a lining overheats its friction falls, which is called fade.
A car with leading-trailing drum brakes rolls backwards down a slope. Compared with going forward, the same pedal force gives:
Reversing the drum swaps the roles: the old trailing shoe now leads and the old leading shoe trails, so the total is unchanged. A two-leading-shoe brake would have two trailing shoes in reverse and lose most of its torque.
Worked examples
Torque of a leading and a trailing shoe · Drum radius 130 mm, lining 40 mm wide from 10° to 130° from the pivot line, pivot 97.5 mm from the centre, actuating force 1.5 kN at c = 201.5 mm, μ = 0.35
- Peak pressure is at θa = 90° (inside the lining), sin θa = 1
- Per unit pa: M_N = w r a ∫sin²θ dθ = 699.10×10⁻⁶, M_F = μ w r ∫sin θ(r − a cos θ) dθ = 335.70×10⁻⁶ (m³)
- Leading: pa = F c/(M_N − M_F) = 0.832 MPa; trailing: pa = F c/(M_N + M_F) = 0.292 MPa
- T = μ w r² pa (cos 10° − cos 130°): leading 320 N·m, trailing 112 N·m
Answer: 320 + 112 = 433 N·m; the leading shoe gives 2.8× the trailing one
Pedal to disc: line pressure, clamp force and torque · Pedal force 300 N, pedal ratio 4:1, booster × 3 (typical), master cylinder Ø22 mm, caliper piston Ø54 mm, pad μ 0.4, effective radius 110 mm, pad area 45 cm²
- Push-rod force = 300 × 4 × 3 = 3,600 N
- Line pressure = 3,600/(π/4 × 0.022²) = 9.47 MPa
- Clamp force = 9.47 MPa × π/4 × 0.054² = 21,689 N; mean pad pressure 21,689/45 cm² = 4.82 MPa
- Torque = 2 pads × μ × clamp × r = 2 × 0.4 × 21,689 × 0.11 = 1,909 N·m per disc
Answer: 9.5 MPa in the line, about 1,909 N·m at each front disc
Heat generated in one stop · 1,300 kg car stops from 100 km/h; front brakes take 70%; each front disc 6 kg of cast iron (c = 460 J/kg·K)
- KE = ½ × 1,300 × 27.78² = 501,543 J
- Per front disc: 501,543 × 0.7 / 2 = 175,540 J
- If the disc absorbed it all before cooling: ΔT = 175,540/(6 × 460) = 64 K
Answer: About 502 kJ in total, 64 K hotter per front disc each stop
ABS, EBD and traction control
Which syllabus covers thisAU CME380 Unit IVVTU BME654D Module 3SPPU not in syllabusMU not in syllabusKTU MET352 Module 3
Which wheels should lock first when you brake hard?
Braking throws weight forward. The front axle's load grows by the deceleration × CG height ÷ wheelbase share, and the rear's shrinks, so the fronts can take far more brake force. If the front wheels lock first the car goes straight but cannot steer. If the rears lock first the back swings round and the car spins, which is worse. Brakes on one axle only stop poorly, especially rear only. Pick the brakes and the front share and see which axle locks first.
What is the ideal brake force split and how does EBD get it?
Both axles reach their grip limit together only if the front share matches its share of the load at that deceleration. That ideal share rises with grip and with CG height, and changes when the car is loaded, so a fixed split is right at only one point. Older cars used a pressure-limiting valve to the rear. Electronic brake force distribution (EBD) uses the ABS wheel-speed sensors and valves to trim rear pressure the moment the rears start to slip more than the fronts.
How does ABS stop a car shorter and keep it steerable?
Tyre grip peaks at roughly 10 to 30% wheel slip and falls when the wheel locks and slides. ABS watches each wheel's speed. When a wheel slows too fast it releases, holds and reapplies that brake many times a second to keep the slip near the peak. A rolling tyre can still steer; a locked one cannot. On loose gravel or fresh snow ABS can stop a little longer, but you keep steering. Try each road surface.
What parts make up an ABS?
A toothed ring and a sensor at each wheel give its speed. An electronic control unit compares them with the car's estimated speed. A hydraulic modulator has an inlet and an outlet valve for each channel and a small pump that returns released fluid. Each cycle has three phases: hold pressure, release it, and build it again. Hydro-mechanical, hydro-electric and air-electric ABS work the same way on different brake systems. ABS has been compulsory on new cars in India since 2019.
What do traction control and stability control do?
Traction control (TCS) uses the same wheel sensors while you accelerate. If a driven wheel spins faster than the others, it brakes that wheel and asks the engine to cut torque, so the car pulls away on wet roads or loose surfaces. Electronic stability control (ESC) adds a steering-angle sensor and a yaw-rate sensor. When the car starts to slide wider or spin, it brakes a single wheel to swing the car back onto the driver's line.
A car's brakes work on the rear wheels only (a failed front circuit). On a dry road with μ = 0.8, the best it can manage is about:
Braking unloads the rear axle, so the rear wheels lock early. For the book's example car (60% front weight, CG 0.55 m high, wheelbase 2.6 m) the limit is 0.8 × 1.04/(2.6 + 0.8 × 0.55) = 0.27 g, about a third of what all four wheels give.
Worked examples
Front, rear and all-wheel braking · 1,300 kg car, wheelbase 2.6 m, CG 0.55 m high, 60% of the weight on the front (b = 1.04 m behind the front axle, c = 1.56 m ahead of the rear), μ = 0.8, from 80 km/h
- Front only: a/g = μc/(L − μh) = 0.8 × 1.56/(2.6 − 0.44) = 0.578 g, stop in 43.6 m
- Rear only: a/g = μb/(L + μh) = 0.8 × 1.04/(2.6 + 0.44) = 0.274 g, stop in 92.0 m
- All four at the ideal split: a/g = μ = 0.8 g, stop in 31.5 m (braking distance v²/2a, without the reaction time)
Answer: 31.5 m with all wheels, 43.6 m front only, 92.0 m rear only
Why a fixed split needs EBD · Same car, fixed front share 70%
- Dry, μ = 0.8: ideal share = (c + μh)/L = (1.56 + 0.44)/2.6 = 76.9%
- With 70%: rear locks at 0.682 g, front would lock at 0.904 g, so the rear goes first at 0.68 g (risk of a spin)
- Wet, μ = 0.3: ideal share = 66.3%; with 70% the front locks at 0.283 g, before the rear (0.330 g)
- One fixed split is too front-heavy on wet roads and too rear-heavy on dry ones; EBD trims rear pressure for each case
Answer: Ideal front share 66% (wet) to 77% (dry)
Braking on a curve · Car on a 50 m radius bend at 60 km/h, road μ = 0.8
- Lateral acceleration = v²/R = 16.67²/50 = 5.56 m/s² = 0.566 g
- Grip is shared (friction circle): braking + cornering ≤ μ g, so a_brake ≤ √(μ² − ay²) g
- a_brake ≤ √(0.8² − 0.566²) = 0.565 g
Answer: About 0.57 g of braking is left, against 0.8 g in a straight line
Wheels and tyres
Which syllabus covers thisAU not in syllabusVTU BME654D Module 2, Module 3 (wheel balancing)SPPU not in syllabusMU not in syllabusKTU not in syllabus
What does a tyre do?
It carries the car's weight on a cushion of air, absorbs small bumps, and passes every driving, braking and cornering force through a contact patch about the size of a palm. The tread shape clears water from that patch; the carcass of fabric and steel cords sets how stiff the tyre is. Air pressure does most of the work of carrying the load, so the pressure printed on the door pillar matters as much as the tyre itself.
How do you read a tyre size like 205/55 R16 91V?
205 is the section width in millimetres. 55 is the aspect ratio: the sidewall height is 55% of the width. R means radial construction. 16 is the rim diameter in inches. 91 is the load index, 615 kg per tyre from the standard table, and V is the speed symbol, 240 km/h. The overall diameter is the rim plus two sidewalls. Change the numbers and watch the diameter and the speedometer error.
Radial or cross-ply tyres?
In a cross-ply (bias) tyre the cord layers run diagonally, crossing each other, so the sidewall and tread flex together. It is tough and cheap, and is still used on some tractors and older trucks. In a radial tyre the cords run straight across from bead to bead, with steel belts under the tread. The sidewall can flex while the tread stays flat on the road, which gives more grip, less heat, lower rolling resistance and longer life. All cars now use radials.
Tubed or tubeless tyres, and how is a puncture fixed?
A tubed tyre holds air in a separate rubber inner tube; a puncture lets it out fast. A tubeless tyre has an airtight inner liner and seals directly on the rim, so a nail usually lets air out slowly and the car can be driven to a repair shop. A tube is patched: find the hole in water, roughen the area, apply rubber solution and press on a patch. A tubeless tyre is plugged with a rubber string from outside, or better, patched from inside.
Why do tyre pressure and wheel balancing matter?
An under-inflated tyre flexes more, runs hot, wears its shoulders, raises rolling resistance and so fuel use, and can fail at speed. Over-inflation wears the centre and cuts grip. A wheel whose mass is not evenly spread has a heavy spot that pulls outward every turn, with a force that grows with the square of speed, so the steering shakes at highway speed. Balancing machines find it and small weights clipped or stuck to the rim cancel it, in one plane (static) or two (dynamic).
You change from 185/65 R15 to 195/55 R16 tyres. At a true 100 km/h the speedometer now shows:
185/65 R15 is 621.5 mm across and 195/55 R16 is 620.9 mm: the bigger rim is matched by a lower sidewall, so the wheel turns at the same rate. Plus-sizing keeps the diameter on purpose.
Worked examples
Decode 205/55 R16 91V · Tyre marking 205/55 R16 91V
- Sidewall = 205 × 0.55 = 112.75 mm; rim = 16 × 25.4 = 406.4 mm
- Overall diameter = 406.4 + 2 × 112.75 = 631.9 mm (unloaded)
- Revolutions per km = 10⁶/(π × 631.9) = 504 (a loaded tyre rolls about 3% smaller, so a few more in practice)
- Load index 91 = 615 kg per tyre; speed symbol V = 240 km/h
Answer: Ø 632 mm, 504 rev/km, 615 kg, 240 km/h
Speedometer error with bigger tyres · Car calibrated for 185/65 R15; fitted with 205/60 R16
- Stock diameter = 381 + 2 × 120.25 = 621.5 mm; new = 406.4 + 2 × 123 = 652.4 mm
- The speedometer counts wheel turns, so it reads true speed × D_stock / D_new
- At a true 100 km/h it shows 100 × 621.5/652.4 = 95.3 km/h; when it shows 100 you are doing 105.0 km/h
Answer: It reads 4.7% low; the odometer under-counts by the same amount
Force from a wheel's heavy spot · An unbalance of 20 g at the rim of a 15-inch wheel (r = 190.5 mm) on a 621.5 mm tyre at 100 km/h
- Wheel speed ω = v/r = 27.78/0.3108 = 89.39 rad/s
- F = m r ω² = 0.02 × 0.1905 × 89.39² = 30.4 N
- It rotates with the wheel about 14 times a second, which is what you feel as steering shake
Answer: About 30 N, as if a 3 kg weight were swinging on the hub
Alternative fuels: CNG, LPG, ethanol, biodiesel and hydrogen
Which syllabus covers thisAU CME380 Unit VVTU BME654D Module 4SPPU not in syllabusMU MEDLO7031 Module 3KTU not in syllabus
Why look for alternative fuels?
Three reasons. India imports more than 85% of the crude oil it uses, so every litre of petrol or diesel replaced saves foreign exchange. Burning fossil carbon adds CO2 to the air, while fuels made from plants recycle carbon the plants took in. And some fuels burn cleaner in towns: CNG gives almost no smoke or particulates, which is why Delhi moved its buses and autorickshaws to CNG. Each fuel needs some engine changes, and each has its own trade-offs.
What is the stoichiometric air-fuel ratio and why does it differ between fuels?
It is the mass of air that holds exactly enough oxygen to burn a kilogram of fuel completely: about 14.6 for petrol, 17.2 for methane and only 9 for ethanol, because ethanol already carries oxygen in its molecule. Fuels with lots of energy per kilogram also need lots of air, so the energy per kilogram of correct mixture is nearly the same for all hydrocarbon fuels. That is why an engine's power changes little between them. Hydrogen is the exception.
CNG and LPG: what changes in the engine?
CNG is mostly methane stored as a gas at about 200 bar in steel or composite cylinders. LPG is propane and butane kept liquid at a few bar. Both are gases when they reach the engine, so they mix well and burn cleanly, and their high octane ratings resist knock. A bi-fuel car adds a tank, a pressure regulator, gas injectors and an ECU that switches fuels. Because gas takes up intake air volume, a converted petrol engine typically loses around 10% power on CNG.
What is E20, and what changes in the car?
E20 is petrol with 20% ethanol by volume. E20 went on sale at selected pumps in February 2023, and from 1 April 2026 the government made E20 with a minimum octane rating of RON 95 the petrol sold at every pump. Ethanol is made from sugarcane, molasses or grain, has a high octane rating, and carries less energy per litre, so mileage drops slightly. Cars built for E20 use ethanol-proof rubber and plastic parts in the fuel system and an ECU tuned for the leaner-burning blend.
Biodiesel and hydrogen: where do they fit?
Biodiesel is made by reacting vegetable oil, used cooking oil or animal fat with methanol (transesterification). It runs in diesel engines, usually blended, with a higher cetane number and less smoke, but it carries about 12% less energy per kilogram and thickens in the cold. Hydrogen has no carbon, so it makes no CO2 at the tailpipe. Burned in an engine it still forms NOx; in a fuel cell it makes only water. Storing it needs tanks at 350 to 700 bar.
Petrol has 44 MJ/kg and ethanol only 27 MJ/kg. Per kilogram of correct (stoichiometric) fuel-air mixture, which releases more energy?
Ethanol needs far less air: 9.0 kg per kg against 14.6. Per kg of mixture that gives 2.70 MJ against 2.83 MJ, within 5%. Only hydrogen stands out (3.4 MJ).
Worked examples
Stoichiometric air-fuel ratio of ethanol and petrol · Ethanol C2H5OH; petrol modelled as CH1.87; air = O2 + 3.76 N2, 28.96 kg/kmol
- Ethanol: C2H6O + 3 O2 → 2 CO2 + 3 H2O (O2 needed = 2 + 6/4 − 1/2 = 3)
- Air = 3 × 4.76 × 28.96 = 413.5 kg per kmol of fuel (46.07 kg): A/F = 8.98
- Petrol CH1.87: O2 = 1 + 1.87/4 = 1.4675; air = 202.29 kg per 13.896 kg: A/F = 14.56
Answer: Ethanol 9.0 : 1, petrol 14.6 : 1
What E20 does to energy per litre · E20 = 20% ethanol by volume; densities 0.789 (ethanol) and 0.745 kg/L (petrol); LHV 26.9 and 44.0 MJ/kg (typical)
- Ethanol mass fraction = 0.2 × 0.789/(0.2 × 0.789 + 0.8 × 0.745) = 0.2093
- A/F = 0.7907 × 14.56 + 0.2093 × 8.98 = 13.39; LHV = 40.42 MJ/kg
- Density 0.7538 kg/L, so 30.47 MJ/L against 32.78 MJ/L for petrol: 7.1% less energy per litre
Answer: About 7% less energy per litre; real mileage loss is usually smaller because the engine burns E20 a little more efficiently
Tailpipe CO2: petrol against CNG · A petrol car doing 15 km/L; the same energy use on CNG (methane); LHV 44.0 and 50.0 MJ/kg
- Petrol per 100 km: 6.667 L × 0.745 = 4.967 kg = 218.5 MJ
- CO2 per MJ: petrol 72.0 g, methane 54.9 g (carbon mass fraction × 44/12 ÷ LHV)
- Petrol: 218.5 × 72.0 = 15.73 kg; CNG: 218.5 × 54.9 = 11.99 kg per 100 km
Answer: 24% less tailpipe CO2 on CNG (157 against 120 g/km)
Electric, hybrid and fuel cell vehicles
Which syllabus covers thisAU CME380 Unit VVTU BME654D Modules 4-5SPPU 402044A Units 4-6MU MEDLO7031 Modules 4-6KTU MET352 Module 4
What are the main parts of an electric car?
A battery pack stores the energy; a battery management system watches every cell. An inverter turns the pack's DC into variable-frequency AC for the traction motor, which drives the wheels through a single-speed reduction gear and a differential, with no clutch or gearbox. An on-board charger and a DC-DC converter for the 12 V system complete it. Electric two-wheelers often put a hub motor in the rear wheel. The Electric Vehicles book covers each part in depth.
How do series, parallel and power-split hybrids differ?
A series hybrid's engine only turns a generator; an electric motor always drives the wheels, so the engine can run at its best speed, but energy is converted twice. In a parallel hybrid the engine and motor both drive the wheels through mechanical links and their torques add, which wastes less on the highway. A power-split hybrid uses a planetary gear to send part of the engine's power straight to the wheels and part through a generator and motor. Pick a layout and a driving mode.
Which batteries do electric vehicles use?
Lead-acid is cheap and heavy, about 30 to 40 Wh/kg (typical), and now mostly starts engines. Nickel-metal hydride, 60 to 80 Wh/kg, was the classic hybrid battery. Lithium-ion dominates EVs at roughly 150 to 270 Wh/kg per cell: NMC for range, LFP for lower cost, long life and safety, popular in Indian EVs. Sodium-ion avoids lithium, and metal-air cells promise much more energy but are not yet practical for cars. Pack-level figures are lower than cell figures.
How does a fuel cell car work?
Hydrogen from a high-pressure tank meets air across a thin membrane. At the catalyst, hydrogen splits into protons that pass through the membrane and electrons that go round the external circuit to drive the motor, then join oxygen to make water. Each cell gives under one volt, so hundreds are stacked. Voltage drops as current rises because of activation, ohmic and concentration losses; efficiency is roughly cell voltage ÷ 1.25 V. A small battery handles bursts and regenerative braking.
How is an electric vehicle charged?
AC charging uses the car's on-board charger: about 3.3 kW from a home socket or 7.2 to 11 kW from a wall box. DC fast chargers, CCS2 in India, bypass it and feed the pack directly at 25 to over 100 kW. The pack is charged at constant current until a cell reaches its voltage limit, then at constant voltage while the current tapers, which is why the last 20% is slow. Fast chargers usually quote 10 to 80% times.
A full hybrid saves the most fuel, compared with the same car without the hybrid system, in:
In the city a hybrid recovers braking energy, switches the engine off at idle and avoids running it at light, inefficient loads. At a steady highway speed there is little braking to recover, so the gain is small.
Worked examples
Driving range from battery size · 30 kWh pack, 90% usable, consumption 130 Wh/km (typical compact EV, mixed driving)
- Usable energy = 30 × 0.9 = 27 kWh = 27,000 Wh
- Range = 27,000/130 = 208 km
Answer: About 208 km; air conditioning and highway speeds cut it
Charging time on an AC wall box · 30 kWh pack from 10% to 80%; 7.2 kW charger; 90% charging efficiency (typical)
- Energy into the pack = 30 × 0.70 = 21 kWh
- Power reaching the pack = 7.2 × 0.9 = 6.48 kW
- Time = 21/6.48 = 3.24 h, about 3 h 15 min (AC charging stays near full power up to about 80%)
Answer: About 3.2 h
Fuel cell stack voltage and hydrogen use · 380 cells at 0.68 V each, delivering 80 kW; hydrogen LHV 120 MJ/kg
- Stack voltage = 380 × 0.68 = 258.4 V
- Efficiency ≈ 0.68/1.25 = 54.4%
- Hydrogen flow = 80 kW/(0.544 × 120 MJ/kg) = 1.225 g/s = 4.41 kg/h
Answer: 258 V and about 4.4 kg of hydrogen per hour at full power
Keep going
- Electric Vehicles interactive book
- Steering geometry calculator
- Ride frequency calculator
- Planetary gear calculator
- How does a car's manual gearbox work?
- How does common rail direct injection (CRDI) work?
- Everything about Ackermann steering geometry
- Vehicle dynamics courses
- All Skill-Lync interactive books
Recommended reading
- Automobile Engineering, Vol 1 and 2, Kirpal Singh
- Automobile Engineering, K. K. Jain and R. B. Asthana
- Internal Combustion Engines, V. Ganesan
- Vehicle and Engine Technology, Heinz Heisler
- Fundamentals of Vehicle Dynamics, Thomas D. Gillespie
- Automotive Handbook, Robert Bosch GmbH
- Internal Combustion Engine Fundamentals, John B. Heywood
- Automobile Electrical and Electronic Systems, Tom Denton
How this book was made
Chapters follow the official syllabi listed above. Every interactive's formulas and every worked-example number were checked by script. Explanations, animations and examples are original to Skill-Lync. Topics informed by MIT OpenCourseWare 2.61 (Internal Combustion Engines), CC BY-NC-SA. All explanations, animations and examples are original to Skill-Lync; MIT does not endorse this page.