LS-DYNA and crash analysis project ideas

17 crash and impact projects that Skill-Lync learners have actually built in LS-DYNA and in HyperMesh with Radioss: drop tests, crash boxes, pedestrian head impact, spot welds and material cards, up to frontal, side pole and roof crush on a full car body. Each one comes with real reports you can read before you choose, the software you need, and one way to extend it into a final-year project.

As of 16 Nov 2026: 3,214 of 1,41,067 public learner reports match one of these ideas · Counts are reports, not unique students

How to pick one

  1. Learn the explicit basics first. Every crash project rests on three ideas: consistent units (most crash models use kg, mm and ms), the explicit time step (set by the smallest element and the wave speed in the material) and the energy balance. The drop test and the Radioss engine file project teach all three on small models.
  2. Then pick the job you want. Crash and safety teams at car makers and their engineering suppliers want the full-car projects (frontal, side pole, roof crush) and head impact. Material and modelling projects (spot welds, material cards, rubber) suit CAE method roles. Bird strike points to aerospace.
  3. Add one design change. Running a given deck is not a final-year project. Changing one thing (a thickness, a notch, a reinforcement) and showing what it did to force, energy or intrusion is. Each idea below suggests one.

LS-DYNA impact and safety project ideas

Drop tests, crash boxes, pedestrian head impact and bird strike.

Drop test of a phone on a plate

BeginnerLS-DYNA, LS-PrePost259 reports

Start from a meshed phone and plate and build the whole input deck yourself: material and section cards, an initial velocity on the phone, a fixed plate, the contact between them, the termination time and the output requests. Then run it and read the stresses and energies.

Make it a final-year project: Drop the phone flat, on its edge and on a corner, and show which orientation gives the highest stress in the screen.

Learn it in LS-DYNA for Structural Mechanics/FEA

Crash box energy absorption at two wall thicknesses

IntermediateLS-DYNA, LS-PrePost232 reports

A crash box is the short tube behind the bumper that crumples first and absorbs energy before the rest of the car is damaged. Crush a rectangular one at 1.2 mm and 1.5 mm wall thickness and compare the section force, the acceleration of a mid-length node, the strains and the energy balance (internal, kinetic, hourglass and sliding).

Make it a final-year project: Add crush initiators (small beads or notches) and show whether they lower the first force peak without losing absorbed energy.

Learn it in LS-DYNA for Structural Mechanics/FEA

Pedestrian head impact on a car hood (HIC)

IntermediateLS-DYNA, LS-PrePost152 reports

Pedestrian protection tests fire a head-shaped impactor at the hood (35 km/h in UN GTR 9, 40 km/h in Euro NCAP) and score the Head Injury Criterion (HIC), worked out from the head's acceleration over time. You run three cases (a simple head on a rigid wall, a foam child head on a rigid wall, the child head on the hood) and calculate HIC for each.

Make it a final-year project: Change the hood's inner panel thickness or the gap to the engine below it and show how HIC moves against 1000, the main limit in pedestrian rules.

Learn it in LS-DYNA for Structural Mechanics/FEA

Bird strike on rotating aero-engine blades

AdvancedLS-DYNA126 reports

A bird model flies along its axis into fan blades that keep spinning at a constant speed inside a fixed casing. Besides the physics, the project teaches deck discipline: bird, blades and casing in separate include files, a main file that calls them, and fixed numbering ranges for nodes, elements and parts.

Make it a final-year project: Model the bird with SPH particles instead of solid elements and compare blade damage and run time.

Learn it in LS-DYNA for Structural Mechanics/FEA

LS-DYNA modelling skill project ideas

Spot welds, joints, mass scaling and element formulations: the details that decide whether a crash model is right.

Spot welds modelled with beam and solid elements

IntermediateLS-DYNA, LS-PrePost209 reports

A car body is held together by thousands of spot welds, so how you model one matters. Join two sheets with beam-element welds and then solid (hexa) welds, tie them to the sheets with a tied contact, drive the assembly into a rigid wall and compare how the welds carry the load.

Make it a final-year project: Add a weld failure criterion and find the impact speed at which the first weld lets go in each model.

Learn it in LS-DYNA for Structural Mechanics/FEA

Spherical, revolute, cylindrical and translational joints

IntermediateLS-DYNA, LS-PrePost112 reports

Crash and mechanism models need hinges and sliders. Build the four basic joints between two rigid bodies and between two deformable ones, using extra nodes and joint cards, drive one part with a prescribed motion and check that each joint allows only the motion it should.

Make it a final-year project: Use the joints to model a real mechanism, such as a door hinge or a seat slider, and report the joint forces.

Learn it in LS-DYNA for Structural Mechanics/FEA

Mass scaling to cut explicit run time

IntermediateLS-DYNA137 reports

Explicit solvers take tiny time steps, set by the smallest element. Mass scaling adds a little artificial mass to those elements so the step can grow. You run the same model with and without it and compare run time, added mass and results.

Make it a final-year project: Plot run time and added mass against the target time step, and find the largest step at which the results still match the unscaled run.

Learn it in LS-DYNA for Structural Mechanics/FEA

Solid element formulations compared on a rubber block

IntermediateLS-DYNA172 reports

Stretch a 10 mm rubber cube (10 elements a side, Ogden material) with four solid element formulations (ELFORM 1, 2, -1 and -2) and compare the stress against the stretch ratio, which is the current length divided by the original length.

Make it a final-year project: Add hourglass control to the one-point element (ELFORM 1) and compare its hourglass energy and stress with the fully integrated ones.

Learn it in LS-DYNA for Structural Mechanics/FEA

Material modelling project ideas

From a raw lab curve to a material card, and rubber models that need more than one constant.

Material card from raw stress-strain data

IntermediateLS-DYNA, a plot digitiser133 reports

Real projects start with a lab curve, not a ready material card. Digitise the true stress-strain curve of a cast iron, clean the points, convert them to the kg-mm-ms unit system, build a piecewise-linear plasticity card (MAT_024) or a power-law one (MAT_018), and check it with a simulated dog-bone tensile test.

Make it a final-year project: Repeat with a steel from a published datasheet and compare MAT_024 with and without strain-rate effects.

Learn it in LS-DYNA for Structural Mechanics/FEA

Mooney-Rivlin and Ogden fits for rubber

IntermediateLS-DYNA, Excel127 reports

Rubber is not described by one Young's modulus. From tensile test data up to 100% strain, find the Mooney-Rivlin and Ogden constants, run both material models and compare them with the test curve.

Make it a final-year project: Fit the constants on data up to 50% strain only, run to 100%, and show how far each model drifts outside the range it was fitted on.

Learn it in LS-DYNA for Structural Mechanics/FEA

Vehicle crash project ideas in HyperMesh and Radioss

Explicit basics, element and material choices, then frontal, side pole and roof crush on a full car body.

Wave speed, time step and the Radioss engine file

BeginnerHyperMesh, Radioss240 reports

Work out how fast a stress wave travels in a steel rail (the square root of stiffness over density: about 5,190 m/s for E = 210 GPa and 7,800 kg/m³), how long it takes to cross 1,000 mm (about 0.19 ms), then set the run time and animation output in the engine file to match. This number is why explicit time steps are so small.

Make it a final-year project: Halve the smallest element size in the mesh and show that the solver's time step halves too.

Learn it in Crashworthiness Analysis using HyperMesh and Radioss

Shell element formulations and energy checks

IntermediateHyperMesh, Radioss, HyperGraph255 reports

Run a base crash model, check the energy error and mass error the solver reports and decide whether the run is acceptable. Then switch every shell to the recommended element properties, run again and compare rigid wall force, internal, hourglass and contact energy.

Make it a final-year project: Add a third run with more integration points through the thickness and compare result change against run time.

Learn it in Crashworthiness Analysis using HyperMesh and Radioss

Radioss material laws and failure models

IntermediateHyperMesh, Radioss234 reports

Run the same part six ways: an elastic-plastic law with a failure strain, the same with a Johnson-Cook failure card that lets cracks grow, without the failure card, with no failure at all, as purely elastic, and with a tabulated law. Comparing them shows what each card actually does to the result.

Make it a final-year project: Calibrate the failure strain so the part breaks at the load a hand calculation predicts.

Learn it in Crashworthiness Analysis using HyperMesh and Radioss

Contact interfaces and notches on a crash tube

IntermediateHyperMesh, Radioss215 reports

Mesh a bumper assembly at 6 mm, set up the contact interfaces, then crush a tube with different notch patterns. Compare rigid wall force, internal and contact energy, cycle count, energy and mass error, and run time across the cases.

Make it a final-year project: Optimise notch spacing for the lowest first peak force with the same absorbed energy.

Learn it in Crashworthiness Analysis using HyperMesh and Radioss

Frontal crash of a car body (Dodge Neon BIW)

AdvancedHyperMesh, Radioss, HyperView287 reports

The crash project most CAE recruiters ask about. Check the unit system and the model, set contacts with friction 0.2 and a rigid wall with friction 0.1, add mass to reach a 700 kg target with the centre of gravity in range, run the impact and report section forces, accelerations and intrusions.

Make it a final-year project: Stiffen one front rail (thicker sheet or a reinforcement) and show the change in peak deceleration and footwell intrusion.

Learn it in Crashworthiness Analysis using HyperMesh and Radioss

Side pole impact on a car body (FMVSS 214)

AdvancedHyperMesh, Radioss, HyperView266 reports

Drive the car sideways into a cylindrical rigid pole and run 80 ms. Report the section force in the cross member, intrusion at the B-pillar, hinge pillar and fuel tank, and the peak velocity of a door inner node, then suggest changes that would reduce fuel tank intrusion.

Make it a final-year project: Add one of your suggested reinforcements and show the new intrusion numbers against the base run.

Learn it in Crashworthiness Analysis using HyperMesh and Radioss

Roof crush analysis (FMVSS 216)

AdvancedHyperMesh, Radioss, HyperView58 reports

A rigid plate is tilted against the roof at set angles and pushed down. Position the impactor with three rotations and a translation, set the contact between plate and roof, apply gravity with the shock tower nodes held, and plot the roof's resisting force against plate travel.

Make it a final-year project: Compare the peak roof force with the car's weight, as the standard does, and test a thicker roof rail.

Learn it in Crashworthiness Analysis using HyperMesh and Radioss

Before you start

These are skill-building projects from Skill-Lync courses, not ready-made final-year submissions. Most start from course-provided models (the phone, the crash box, the Dodge Neon body), so for a final-year project you need a design change or a question of your own, which is what the extension ideas are for.

The reports are learner submissions. Quality varies, and some contain mistakes, so treat them as a view of the work, not as answers. Many learners did the same challenge, so several examples share a title. Copying one will not get past a viva.

The theory exercises from the same courses (unit conversion, explicit versus implicit) are not listed: they are reports, not projects. The full-car crash projects use Radioss, not LS-DYNA; the section title says so.

Questions students ask

What are good LS-DYNA projects for a beginner?

Start with a drop test (a phone dropped on a plate), where you write every card of the input deck yourself, then a crash box crushed at two wall thicknesses. Both run in minutes on a laptop and teach contacts, initial velocity, outputs and energy checks. Move to spot welds, mass scaling and material cards next, and only then to a full vehicle.

Is LS-DYNA free for students?

A limited version is. As of 16 Nov 2026 Ansys offers LS-DYNA Student as a free add-on to Ansys Student. It includes the LS-DYNA solver and LS-PrePost, with a cap on model size, which suits the drop test, crash box and material projects here. Check the cap against your model before you plan a full-vehicle run.

LS-DYNA or Radioss for crash analysis?

Both are explicit solvers that do the same physics. LS-DYNA is very widely used in vehicle crash work. Radioss comes from the HyperWorks suite, alongside the HyperMesh pre-processor (both now part of Siemens). Learn one well; the habits (units, time step, contacts, energy checks) carry over. Check which one your target employers name in their job ads.

What is a crash box?

The short metal tube between the bumper beam and the front rails. In a low-speed impact it folds up like a concertina and absorbs the energy, so the rails and the rest of the car are not damaged. Crash box projects compare wall thickness, shape or notches for how much energy they absorb and how high the first force peak is.

What does HIC mean in a head impact project?

Head Injury Criterion, a number worked out from the head's acceleration over time during the impact. Higher means a greater risk of head injury. Pedestrian protection rules use HIC 1000 as the main limit, and car makers design the hood and the space under it to stay below it.

Turn a project into a job-ready portfolio

Talk to a counsellor.

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.