Concrete mix design for M35 grade concrete with flyash . Grade of concrete = M35 characteristics strength (fck)= 35mpa standard deviation =1.91mpa target mean strength fck=fck'+1.65xs.d(from is 456-2000)                                  …

Dimensions  Dimensions of Ground floor plan: Living room: 4.5 x 2.5 metre. Pooja /meditation : 1.5 x 1.5 metre. Dinning room : 1.5 X4.0metre. Wash room : 1.2 x 2.5 metre. kitchen :3.0 x 3.0metre Master bed room : 4.5 x 2.5 metre.     Dimensions of first floor plan: Bedroom -1 : 4.2 x4.8 metre. Bedroom -1…

1) Aim : creating the geometries from P1-P2 using all coordinate system and also Line tool to create the geometries Introduction: In Autocad we have 3 types of co-ordinate systems: 1)Absolute co-ordinate system 2)Relative co-ordinate system 3)Polar co-ordinate system. 1. Absolute co-ordinate system: All Inputs specifying…

AIM: To Create a Floor plam,Footing details,and Isometric view using Auto cadd procedure: Open Auto cadd software In the command bar type rectangle  and press enter. specify first corner of rectangle. enter dimensions of length as 0.90 and width as 0.25. specify the other corner. specify line from Ribbon. specify…

Aim : To Draft various Geomentries using Chamfer,Fillet tool by using Autocadd. Procedure : In auto cadd we use chamfer ,fiileet for different purposes based on the usage inn the autocadd. So Now i will show you some of the examples how to use chamfer and fillet commnads in auto cadd. Drawing 1: Open new autocadd file…

please find the attachement of residence plan layout.

AIM: To create a column schedule using necessary commands. Introduction:  structural columns are identified in a column schedule by intersecting the grid lines and by their top and bottom constrained and offsets. Page setup: open new page Select architectural. Precision as 0-01/256” and apply Press ok enter.…

1AIM: To draw the elevation and details of the wardrobe. Procedure:  units set up are in MM. Limits & Limits max are also set. Zoom command also used. In the command line type rec 2800,2600 In the command line type offset. Offset from the top of dimension 12 and 488 mm   In the command line type offset. Create…

AIM: To create a new project  and name the project appropriately. Procedure: step 1: OPEN REVIT. click the window button and type revit and press revit. once the revit is open the home page will fallows. step :2  creating construction template. click on new from home page. in the dialogue box click on  construction…

1.)Building Information Modeling (BIM) is the foundation of digital transformation in the architecture, engineering, and construction (AEC) industry. As the leader in BIM, Autodesk is the industry's partner to realize better ways of working and better outcomes for business and the built world. Improve Onsite Collaboration…

1) Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with grids created from…

1.Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level procedure:The creation of ceiling with in a revit family is a similar process to that of floors and roofs you can enter sketch mode & literarlly sketch out…

1.National Building codes (NBC):  The National Building Code (NBC) is a standardised set of rules to be followed by authorities and construction firms, to provide a healthy and safe living experience for all residents The National Building Code (NBC) is a document that provides guidelines for construction of structures…

1) Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project Aim: To set project base point and project shared coordinates of the project. Procedure: to create project shared co-ordinates. Open Architectural tab. open manage tab. click on project coordinates…

1.) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School Ans : Multi - unit  office building. 2) Assume reasonable assumptions for geographic and…

1.What are HVAC systems? Why are they essential in the modeling of buildings HVAC SYSTEM:HVAC systems are very important during the architectural design of a building for the following reasons The success of an HVAC system is directly related to the building’s comfort levels. HVAC systems require substantial floor…

AIM: To Draw plan elevation ,& section of house in auto cad.  Procedure :Steps for drawing plan. Open auto cad and enter UN (units command) in the command box and select type as decimal and set precision as decimal  as 0. select X-line command and draw horizontal line and vertical line. Trim the unwanted…

AIM: To draw  1. Architectural drawing of a building.    a) Plan of a two storey building.    b) Elevation of a two storey residential building.    c) section of a two storey redidential building. 2.    Column palnlayout of the building.        Beam plan…

Drawing :1 Procedure:  1. create the following template using the drafting tool Using MTEXT,give the req text. The font is taken as TIMES NEW ROMAN. Create block of the template madeand given the name of the block as custom 1 _Title block. Create the templates as shown in using Drafting tool. Add the following text.…

A. KITCHEN LAYOUT: AIM: TO Draw kitchen layout. Procedure: First we draw below counter. we create a wall by creating a rectangle of 4300 x3200 mm. Draw an offset of 230mm wall thickness  towards outside. Now we draw left cabinet and fridge. We draw the fridge by creating a rectangle. Take an offset of 1000mm and start…

TASK 1 : 1. Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use ATTEDIT command to edit the information in the title block. Use A1 size…

1. Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing. Command used: 1. Rectangle tool 2.Extrude 3.subtract 4. UCS 5.Box 6. Offset 7.Move 8.Sweep 9.Cone 10Region. 11. Boundary. Procedure: Open auto cad. set the units as imperical  units set to engineering with predcision 0'0"…

1. Create a 3D Isometric View of the building with plan and elevation given. Procedure: open auto cad 3d. set -top view. set units to enginerring and inches. select liits 0'0' and 100',100'. now use rec command to draw rec of size 10'9" x10'9" make 9" offset inside the rec as shown  now trim both the lines and extend…

AIM:Create a 3 dimensional model of the residential building with a rendered view.   PROCEDURE: To create a 3d dimensional mode of the residential building i have drawn a randon plan size  10000x8000 sqm which have required rooms the plan and elevation details are below To create a 3d dimensional window and door…

1) Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below           a. Using 3D model create a section box           b. To create similar doors and windows in a floor plan layout         …

1.Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. ANS:Tools used: 1. Manage. 2.Dynamo block. 3.Code Block. 4.math.sin 5.integer slider. 6.add 7point by co-ordinate. 8.Surface lost Procedure: open the revit and select the new template. save the file go to manage tab…

1. Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class AIM: Use the architectural / structur project file develop by you in 6-8 week. export the revit architecture revit…

1.A) Explanation:This crack will be formed due to the flexural failure of a beam. The flexural strength, known as modulus of rupture, bend strength, or fracture strength, is a material property, defined as the stress in a material just before it yields in a flexure test. The flexural strength represents…

Question 1: Compute lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The system has 3 DOFs as shown. Assume L = 2h and Elb = Elc   Ans:   2. Question 2: For the following structures: Determine the number of degrees-of-freedom for dynamic analysis Establish…

ANS:  

  Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. ANS: Symentry: It is observed that the distribution of mass,stiffness…

Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account…

OBJECTIVES : To Know modeling of a high rise building using E-Tabs. AIM: To model a 25 storey building using ETABS with reference of IS 1893 Introduction: ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions,…

;PProject 1 – Factors influencing the dynamic characteristics of a building. Buildings oscillate during earthquake shaking. The oscillation causes inertia force to be induced in the building.  The intensity and duration of oscillation, and the amount of inertia force induced in a building depend on features…

The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span continuous beam along grid A        2) 7 span continuous beam along grid…

AIM: To run the analysis and design the RCC moment resisting frame of the given ETABS file. Provide details of longitudinal reinforcement for the two columns (3A and 3B) from foundation level to terrace level. To sketch the column cross sectional & elevation details or draft it using AutoCAD software. To show shear…

Aim:- To model and analyze the G+6 residential building from the given architectural drawings using the ETABS 2018. Introduction:- ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods and…

Aim:- To model and analyze the G+7 residential building from the given architectural drawings using the ETABS 2018. Introduction:- ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods and solution…

Obkectives of challange: To know general design procedure of spread footing with hand calculations. To practice how inputs can be collobrateda and arrrived as data for calculations. How assumptions are helpful when certain inputs are not available.   Procedure :StepsInvolved inFooting Design: Calculation of Gross…

Objectives of challange: To know the general Design Procedure of spread Footing with SAFE software. To know the general Design procedure of pile foundation with SAFE software. Procedure: Data Required for safe and analysis design. Unfactored load = 2000/1.5 = 1333.3 KN. Dead load break up = 1333.3/2= 666.7 KN. Live load…

Aim: Design and analysis of  a hostel building situated in Guawahti using E-tabs and SAFE. DESIGN Codes used: The following is design codes required for reference. IS1875 -PART-1 IS1875-PART -2 IS13920. IS1893. IS29311 -PART-2 IS456 SP34.  Required Data: The wall will be made of AAC block. other loads are to be calculted…

1. STAAD pro ( Structural Analysis and Deign program is the abbrivation for the STAAD it is the connected version new version used to analize the RCC structure and steel structure by using this software ) It Include the GUI Graphic User Interface for Visualization and contains various design codes. Procedure   …

1.A.  Column are the vertical member in the Structure that can be of varing size in dimesions    The circular section of column are provided at the upper floor of the building for the better load carrying and access purpose. Procedure :   Create the model in the staadd pro that can be a column. …

1.1 The primary load cases that are to be considered for design are listed below: Dead Load (IS 875: Part I). Live Load (IS 875: Part II). Wind Load (IS 875: Part III). Snow Load (IS 875: Part IV). Seismic Load (IS 1893: 2016). 1.2. One-way slab is a plane surface of uniformly loaded which deforms into a cylindrical shape…