1 - Project - Speed Control of a Direct Current (DC) motor      AIM:  The Main motive of this project to develop a model for Speed control of a direct current (DC) motor by using PID controller      OBSERVSTION: First I create a Simulink model for the DC motor were developed as per…

Project 1; Develop a double-acting actuator model using Simscape Multibody and Simscape components Aim:   To Develop a double-acting actuator model using Simscape Multibody and Simscape components. The mechanical system of the cylinder needs to be built using Simscape Multibody library components…

Projet - 1; Development Of a Forward Energy-Based Fuel Consumption Model Of a Conventional Vehicle Aim: Computes fuel consumption values ​​for a given vehicle (kmpl) in city cycles (UDDS) and highway cycles (HWFET). It also analyzes and understands the vehicle's operating point in terms of engine speed, torque, transmission…

Project - 2: Development of a forward energy-based fuel consumption model of a P1 hybrid vehicle Aim: Computes fuel consumption values ​​for a given vehicle (kmpl) in city cycles (UDDS) and highway cycles (HWFET). It also analyzes and understands the vehicle's operating point in terms of engine speed, torque, transmission…

Q1] Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip. Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html) Tyco 174357-2…

Q1] Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. P clamp Answer: First download the P clamp file were given question and load into the Catia V5 Next to select the part design for  define the geometric parameter for…

Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end)   Download connector…

Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use the connectors provided. After completion of routing, Check the bundle Continuity. Add snap of result in submission Add annotation to all connectors. Make an assumptions for annotations like connect 1 , 2 etc…

Q1. Flatten the harness assembly completed in “ week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view.       Answer: First Need to load the week 4 challeng file in the catia v5 and save in the new folder named…

Wiring Harness For Engine   Aim: To route the wiring harness on given Engine and flatten view drawing in CATIA V5 Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design Apply Protection coverings as required. Objectives: The goal of this project is to route…

Assemble and apply GD&T to the butterfly valve assembly drawing Aim:   To create the Butterfly Valve part and assemble the part and also apply the GD&T with Drawing sheet Objectives:  The Main objective is to create and assemble the various component of butterfly valve using simens NX CAD  Assemble…

This project focused on the meticulous design and routing of a wiring harness for the rear door assembly of a car, utilizing CATIA V5 software for comprehensive modeling and documentation. The objective was to ensure optimal functionality and durability of the wiring system while adhering to stringent industry standards and packaging rules.

1 Question: In this week’s assignment, you will have to create 2 assemblies according to the content covered in the course videos. You will be provided with 2D diagrams of the components and you will have to first create the individual part files and then create a complete assembly of those part files in the assembly workbench.…

AIM:        To Create the Base Bracket Plastic component through the given Class-A surface INTRODUCTION: CLASS A SURFACE:                  Class A is the surface created by concept sketches done by free hand sketches. The finished sketch is then transferred to a computer, and the 2D surface is created using software such…

AIM: To create the Switch Bezel Plastic component through the given Class-A surface.  : CLASS A SURFACE:                 Class A is the surface created by concept sketches done by free hand sketches. The finished sketch is then transferred to a computer, and the 2D surface is created using software such as Alias. This computerized design is known as a Class A surface.…

AIM:    To Create the Bumper Plastic Component Trough the given Class A Surface were given below. INTRODUCTION: CLASS A SURFACE: A surface created by the designer is used as input for the plastic modeler to work with It is an aesthetic surface and outer surface.     CLASS B SURFACE: A surface that is smaller by a certain…

AIM:      To Create the RIB & Screw Boss for the Drill Handle and also follow the Design rule.   STEPS FOR CREATION OF DRILL HANDLE: Tooling Axis: Manually arrange the view to choose the ideal tooling direction that covers the majority of the surfaces. First Extract the boundary and create the dummy tooling axis  Now create…

AIM:    To create the Dog House for the Door Trim Considering the design rules. OBJECTIVES: Consider the thickness of the part should be 2.5mm 'C' is where the dog house contact the back side of the surface Dog House wall thickness at the intersection of the part wall (C) should be 40% or less than the main wall…

AIM:       To Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.    OBJECTIVES:…

AIM:     To construct the tooling axis, complete the draft analysis for the final solid component, then develop the A Pillar Design using the master section as the intersection sketch with the Class A surface. OBJECTIVES: Utilizing the master section and the bisecting approach, create the necessary tooling…

The project described focuses on the development of a door trim panel using CATIA V5 software, following the standards and practices typical in the automotive industry, especially among OEMs and tier 1 suppliers. The primary goal is to create a CAD model that meets rigorous criteria for aesthetics, functionality, and manufacturability.

AIM: To Design Hood/Bonnet with the necessary reinforcement by following the master section mentioned with the design parameters OBJECTIVES: To Design the Outer panel To Design the Inner Panel with Master Section To Design the Reinforcement for the striker and hinges OUTPUT REQUIRED: A detailed report about the Hood Design…

AIM:  In order to assess the hood's strength and optimize the design to see variations in the bending strength, we had to compute the section modulus of the hood. A structure becomes more resistant to bending as its section modulus increases.  OBJECTIVES: Come up with a new section that has an improved section…

AIM:      To create a fender utilizing input class A surface, a drip area using a specified master section as a reference, and a variety of mountings such as sill mount, bumper mount, and A-pillar mount. INTRODUCTION:  What is a fender?             A fender is a component…

AIM:    To Create the Roof Design with the assembly by developing the essential flanges for the required design OBJECTIVES: The main objective of these project is to create the Roof sheet metal design using NX CAD with essential flanges for the roof, like the Front Roof rail, Rear Roof rail, Center Roof rail,…