Ans 1 : (a) The image  given in the Q1(a) Soft Storey Mechanism  When  the ground floor or basement floor is kept opened because of parking or because of retail shops or so  without considering the stiffness distribution along the height of the building lateral stiffness is reduced in the upper…

  given that :- Different mode shaope values for different Time periods Need to find:-Mn,LN,`Gamman`,Mn*,Base shear   `phi1=[[``0.334],[0.641],[0.895],[1.078],[1.173]]` `M1=phi nTm Q` `=[[0334,0.641,0.895,1.078,1.173]]*m[[0.034],[0.641],[0.895],[1.078],[1.173]]` `=[154459/4000]m` M1=3.8641m similarly WE KNOW…

Ans1:-Aim:- To comment on the stiffness,redundancy,bidirectional stiffness , ductility of the given layout a)Symmetry:- by looking at the giving layout ,it was observed that distribution of mass and stiffness is across the plan .The plan has good symmetry which leads to the  reduction of horizontal displacement In…

Ans 1:- Aim:- To compare the  three alternative plans taking into account the floor shrinkage,lateral stiffness and torsional one with respect to the vertical axis ,the vertical reinforcement. Soln:-A structure is more restrained it will be more expanding,shrinking and cracking. There will be more floor shrinkage…

Aim:-To  model and Analyse 25 storey building with given specifications and to cross check the parameters as per is 1893 provisions. Given data: Materials used :- Concrete M30 grade                                …

Ans: Aim:- Comparative study of buildings Frame section properties: Beam -300 mm*400 mm Beam -400 mm*400 mm Beam -600 mm*600 mm Beam -800 mm*800 mm Beam -330 mm*500 mm Beam -500 mm*330 mm Shell Section property Slab -150 mm thick Load: Live load-3kN/m^2 Infill wall load-10kN/m^2   Modelling of Building A:- Open the New…

Ans:- Aim:-To Provide the longitudinal and shear reinforcement for the Given Continuous beams and to calculate the maximum shear force in   Steps to be followed are as shown below For the given structure go to Analysis and run the structure. Go to concrete frame design. Then click on start design / check. Once the…

Ans:- Aim:- To provide the longitudinal Reinforcement of  the columns from foundation to  Terrace level and to sketch the column cross sectional  and elevation details in Autocad.            To show the shear reinforcement and lapping details as per Clause…

Ans: Aim:-To provide the exact values of longitudinal steel ratio, boundary element length and shear reinforcing ratio from the design results. To provide c/s steel arrangements of shear wall from its base upto terrace ,as per IS 13290-2016 To provide elevation drawings of the reinforcement details of the shear wall from…

ANS) AIM:-To Create and Analyse the given building in ETABS 2018, the structural model has to be prepared in accordance with IS 1893 and as per IS 13920. And to run a model response spectrum analysis and check the Analysis of inter storey drift requirements, vertical and planar irregularities, minimum shear wall requirements,…

AIM:-To Create and Analyse the given building in ETABS 2018, the structural model has to be prepared in accordance with IS 1893 and as per IS 13920. To design the pile cap and pile reinforcement details,Tie  beam  connecting the pile caps, to sketch the column reinforcements, to produce the framing plan and beam…

Ans1: Aim:-To create a new project (Structural/ Architectural/Construction Template) and name the Project appropriately. Tools used: File, New, save Procedure Open the software Revit 2021. Once the software is opened click on the new ,New project dialog box will appear select the structural, click ok Click on the File…

Ans 1:- Building information modelling (BIM) is an intelligent 3D model -based process that gives architecture, engineering and construction(AEC) professionals the insight and tools to more efficiently plan,design, construct and manage buildings and infrastructure. It isa process supported by various tools, technologies…

Ans1:- Aim:- to create floor layout from week 2 Project Tools used:- Wall Command Architectural , Floor command. Property Command. Edit Property Command Procedure: First open the revit software and click on new and select architectural unit In the next step go to Architecture tab and click on walls and start drawing the…

Ans 1:- Aim:- To model a ceiling  from the architecture tab above the first floor level  Commands used: Architecture , Ceiling Procedure: Open the model Click on the architecture tab and select ceiling Select the celing and click on sketch ceiling Draw the ceiling in required shapes and adjust the height and…

Ans 1: With the help of revit we can draw , design and model a structure. Only designing or modelling is not the task. the biggest task is to   design the building as per some of the standards rules and regulations  to ensure the safety and coordination. There are lots of  type s of buildings depending…

Ans 1:- Aim :- to set the base point of project using manage  tab and project shared coordinates for the project Commands used:- Collaborate, Architectural, Grids, Manage Procedure:- Open the revit Select the architectural template click ok. Go to Architectural tab click on datum and then on grids Draw the grids and…

Ans 1:- Aim:- To create an Architectural and structural model with 3D rendering using revit My project  is to build Office building. Ans 2:- Aim:- To assume reasonable assumptions for geographic and location details for the project modelling My project will be constricted in the commercial Area, Bangalore My building…

Ans 1:- HVAC  system is one of the important component in the modelling of a building. The term HVAC  stands for the Heating, ventilating and Air conditioning, now lets get into these terms , heating means to increase the temperature of input Air which flows into the building, ventilation can be defined as the…

Ans 1:- The shortcut keys for the above mentioned tasks are: Using 3D model creates a section box=BX Select the section and type bx and we will get the section To create similar doors and windows in a floor plan lay out= CS Select the section and type cs and we will get the similar doors or windows     To reduce…

Ans 1:-Aim:- To create  a set of sinusoidal points  and create a curve and create a surface out of the curve Procedure:Open the revit softwareGo to manage tab and select dynamo under visual  programmingOncethat is done then go to search bar and search for range  and connect the integer sliders…

Ans 1:- Aim:-To use the architecture/structure project file developed earlier  and export it to Navisworks Procedure : Open the  3d view of building go to file and click on export and select NIWISSave the file as niwis file Open the navis manager software in order to import the file from the revit.   Ans…

Ans 1:- Aim:- to summarize the user interface in TSD Project workspace:- Open the Tekla software and click on new from file option We get the project work space we can access it. Scene Content On the project workspace , we can see there is an option at the right side of interface called scene content It is used to filter…

  Ans : To model columns for industrial steel structures using TSD Introduction Tekla structural designer is an integrated model based 3D tool for analysis and design (of both Concrete and steel members)in multi-  material structures. Features include modelling, automated structural analysis and design, drawing…

Ans 1: Aim:- To create beam properties for first floor and model the beams Procedure: Step 1: Go to TDS software Open the challenge 2 file Go to home tab and select manage properties sets Define the breams B2 and  go to model and select steel beams and draw the beams as shown below Now when we refer the given first…

Ans 1:- Aim:- To calculate the loads 1 Dead load calcultion         Self weight of slab         Finishes 50 mm     unit weight of concrete 24 kN/m^3                 1.2 kN/m^2             2 brickwall…

ANS 1:- Aim:- To generate manual wind loading in the design report based IS code as per following input which are mentioned in the question Given data:- Wind speed-32 m/s^2 Life of structure-50 years Class of structure=class A As per iS 875 part 3, clause  5.3.2.2 structure and /or  their components as cladding…

please check the file attached below

please check the attached files

please check the attachment below

i have attached  the document below  please check it .

  Ans 1:- Aim:- to generate seismic  loading based on IS code provisions Procedure:-   Open the  previous model and then go to load cases and add seismic load cases.  In the next step go to loads toolbar then click on seismic load and then  seismic wizard and select code spectra and click…

please checked the attached file below

Ans 1:- Aim:- To design the slab and foundation of the model Tools used:- 1st order analysis, Analysis all( static), status, check panel, properties window  etc. Procedure:- Open the file modeled in Tekla structural design  and open 3D view Click on first order analysis and perform analysis Click on the status…

Ans 1:- AIM:- to generate the  report  for the steel  building design Procedure:- Open the Tekla model Now go to report option from the ribbon and select model report Now select the load cases and combinations summary to obtain report Click on the show report to obtain report We can change the project name…

Ans 1:- Aim:- To model Rc structure analyse and design the model elements as per  IS codal provisions PROCEDURE:- B Open A New Tekla template in Tekla Go to settings from home tab  Assign the design codes and units to be considered in the model Define the structural default setting Click on ok Step 1:- …