AIM:- To Create the Boss and Dog House  for the  coin holder considering the design rules. OBJECTIVE:-  To Create The Boss and Dog House. The tooling axis creation using particularly the Bisecting method.  The draft analysis report on Dog house and main Component. THEORY:- Class B- surface…

AIM:- To Create a door applique design from Class A- Surface  and To Create enginnering Features to fit the Component in the main surafece and Create the Heat Stakes and the locators considering the design rules mentioned in the challenges for the door applique. OBJECTIVE:-  TO Create Class B Surface and Class…

AIM:-To create the solid part models and assembly for the given drawing below with a report. OBJECTIVE:-  To Create sketches from given drawing and create solid part model. To Create the assembly. THEORY:-  QUICK RETURN MECHANISM:- A quick return mechanism is an apparatus to produce a reciprocating motion…

TITLE:- Challenge for Week-02 AIM:- To make a simulink model of Doorbell Using Solenoid Block and To create a simulink model of Fan Condition using a thermistor to sense the temperature oa a heater and turn on or turn off the fan. OBJECTIVE:-  To create simulink model of Doorbell Using Solenoid Block and To create…

TITLE:- To Making The model for "Washing Machine Simulation & Gear Shifting" Aim :-   To make control logic of a"Washing Machine" using stateflow. To create Simulink chart for the"Gear Shift" logic. THEORY:-  What is Control Logic:-        Control logic is a key part of a software…

Project - Master Section Development. Aim:- To create the Solid body Using Closed Body Command of B Piller From the Given Class A Surface and Create of Engineering Feature. Objective:-  To create Class B surface & Class C surface From Given Class A surface. To make Closed Body Using closed body command. Create tooling…

TITLE:- Project Report of  Simulink for Mechanical and Electrical Engineer. AIM:- To make Detailed report on BAJA  all- terrain vehicle (ATV) model and Study of Continuously Variable Transmission System Using Modeling on MATLAB Simulink. Objective:- To make technical report for BAJAJ all terrain vehicle (ATV).…

AIM:- To study on different vehicle model using  ADVISOR Tool and Simulink in MATLAB. ADVISOR Tool:- ADVISOR a system analysis tool for advanced vehicle modeling (Advanced Vehicle Simulator).The US department of energy ADVISOR written in the Matlab/Simulink enviroment and it developed by the National Renewable Energy…

Aim:- To Study on EV Drivetrain. Quetion:- 1] Which types of power converter circuits are employed in electric and hybrid electric vehicle?  Ans:- Power Converter  Circuits for EV( Electric Vehicle) and HEV(Hybrid Electric Vehicle):- AC-DC Converter( rectifier) DC-AC Converter(Inverter) DC-DC Converter(DC…

TITLE:- Final Project of Door Trim Panel. AIM:- To Creating a Door Trim panel from given Class A Surface Considering Class A surface , Thickness of component, Attachment mechanical feature With the help of Master Sections. Give Class A Surface with Master Sections:- OBJECTIVE:-  To developing the Door Trim Model of…

AIM:- To study on DC Motor Control. Question:-1] A. Explain a MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge’.                    B. Comment on the armature current shoot-up from the scope results.        …

Aim:- To study on Wide Open Throttle (WOT) Part-2. Objective:-  Compare between mapped and dynamic model of engine, motor and generator.How can you change model type How does the model calculate miles per gallon? Which factors are considered to model fuel flow?  Run the HEV model with WOT drive cycle and Change…

Aim:- To calculate the Energy required for braking and Study on Different method of Braking. Objective:- To defined driving cycle and calculate the energy required for braking. Why electric motor can’t develop braking torque at high speed similar to starting? How electric and mechanical brakes are coordinated.…

AIM:- To Study on Overview of an aircraft & Its Parts. OBJECTIVE:- To list out the total weight of various types of aircrafts. Compare difference between Ground Speed & Air Speed. To study about take off power, tyre design, rolling resistance, tyre pressure, brake forces when landing. To calculate the force…

TITLE:-  Final Project for Design of an Electric Vehicle. AIM:- To Create a model of electric car which uses a battery and a DC motor using MATLAB software and Choose suitable blocks from Powertrain block set. OBJECTIVE:-  To make a most Simple and Low run time Vehicle model using individual component…

Aim:- Study on Different Battery Chemistry. Question:- 1] Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells.Give your detailed explanation on it. Ans:-  Table of including materials & chemical reactions occurring…

Aim:- Study on Estimation of State of Charge(SOC) and Battery Management System(BMS) Implements Coulomb Counting for SOC . Q- 1]Simulate the 3 test cases from harness dashboard and write a detailed report on the results Ans:-  The below model shown the of BMS Closed Loop:-    Simulate the 3 test cases…

Project- (1):- Mechanical design of battery pack. Objective:-  Battery pack capacity:- 18 kWh Cell:- ANR26650M1-B  Prepare a detailed battery pack drawing along with its enclosure. State your assumptions. Introduction:-  An Energy storage system is a device which store energy, discharge and also get charge,…

PROJECT 2:-  Thermal modeling of battery pack AIM:- Create a 10 cell series lithium ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB. ABSTRACT:- Now a bay Lithium-ion cells are widely used for Electric Vehicle…

                                                          Final Project:- Electric Rickshaw modelling. AIM:- Designing a MATLAB (Simulink) model of an Electric Rickshaw (Three…

Advanced Sheet Metal Design Using NX Cad Challenge_1_Casing Design Title of the Project:- To design the Casing Design and Perform Operation tool on sheet metel using in NX CAD Software. Objective:-  The main objective what is the Sheet Metal Basics in this project. To study the fundamental and advance tools of NX…

Title:- To Design an Odd Enclosure Using Sheet Metal NX CAD. Objective:-  In this Project to create is design Odd Enclosure Using command name as Solid Body, Sheet Metal from solid,Flanges,Jog or Bend, Hole, Cutout, Dimple, Louver Feature,Rebend,Unbend areas and Flat Pattern and Drafting Using in sheet Metal NX CAD. Introduction:-…

Title:- Design Backet in Using Sheet Application Using NX CAD. Objective:- In this Project I have Created Bracket L-shape with the help of 2D sketches. Introduction:- In mechanical engineering a bracket is any intermediate component for fixing one part to another, usually larger, part. What makes a bracket a bracket…

Title:- To modelling Metal Bracket-II and Drafting Using Sheet Metal Application Using NX CAD. Objective:- In this project we have create the Metal bracket-II and using various feature tool like Countour Flange, Normal Cutout,Corner Break, Unbend and Rebend, Hole, Advanced Flange and Gusset. To create 2D Drawing Sheet…

Title of the Project:- To design the Box Assembly and Perform Operation tool on sheet metel using in NX CAD Software. Objective:- The main objective what is the Sheet Metal Basics in this project and the lern about fundamental and advance tools of NX CAD. In this project I have Design the Box Assembly and Apply various…

Title:- Study about Underbody Coating. Question- Write one page about Underbody coating and its purposes. Ans:- Underbody Coating:- Underbody coating provides long term protection from corrosion to car's underbody. It also protects parts like internal body panels, frame rails and other inner cavities that are…

Question:- 1]  Benchmark with presently available cars in the market for the following case.Mr. D.S. Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His Family comprises five members including his wife, five-year-old boy, his father, and his mother. He visits his native…

Title:- Assemble and apply Geometric Dimensioning and Tolerancing (GD&T or GD and T) to the betterfly valve assembly drawing Objective:- To created the 3D part of the butterfly valve sub part name like, Main Body, Shaft, Lever, Nut , Screw, Disc Plate etc. To apply Geometric Dimensioning and Tolerancing…

Title:- Design Fender- Wheel Arch. Objective:- In this challenge to Calculate the Wheel Arc area and prove whether the car will pass the standards or Not. Given part file of Wheel Arch:-               Introduction:- Wheel Arch-  It is a semicircular profile above wheels…