Introduction BENCHMARKING is a processof evaluating and comparing an organization's performance, products,design, services, or processes against other in the same industry or field to idenify best practices and area for improvement. The objective of benchmarking is to identify and learn from industry leaders ,set performance…

 UNDERBODY COATING      Underbody Coating is a protective layer applied to the underside of a vehicle to protect it from rust ,corrosion and damage caused by exposure to moisture, salt, and other road debris.       It is typically made of rubber, plastic, or a specialized…

DRAFT ANALYSIS: BY CLASS A SURFACE Step 1: Check the connectivity of the Class A Surface Ensure no graps Step 2: Create a Point on Middle Hole by using point command Step:3 By using YZ plane and point create an intersection on the Class A surface Step 4:  Create a bisecting line using the lines shown That pink line…

Create the Switch Bezel Plastic component through the given Class A Surface.To begin with the tooling axis for the given Class A Surface should be created the requirements of the draft angle and at the perfrom the Draft Analysis on the model   Thickness of the component to be 2.5mm TOOLING AXIS In this model we use…

Create the Coin holder  Plastic component through the given Class A surface .To begin with the  tooling axis forr the given Class A surface should be created meeting the requirement of the draft angle and at the end draft Analysis on the model . Take the thickness of the component to be 2.5mm Tooling Axis: For…

In this model we use Bicsectinh line method to form tooling axis In Class A surface select the base section abnd extact it and make a point centre of the surface by using point command Now orgin the axis system on that point Then ceate a sketch on YZ plane Take intersection  on class A and create  two line on…

BUMPER DESIGN AIM Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. INTRODUCTION A car bumper is a vital component of an…

TOOLING AXIS Here first we required tooling axis for draft analysis.Tooling axis is work as provided to direction for injection moulding as well as direction of draft angle where is check it right or wrong.So first wee extract tghe surface of class A and than create point on it use this point we create the line by using…

  TOOING AXIS:      The tooloing Direction is basically the direction that the mold opens apart.The mold is made in two separa halves basically .you have a cavity side and core side. The core pulls apart from the cavity and thats the dye line or tooling direction. Check for gaps between suface…

AIM: Create the dog house for the door trim OBJECTIVE: Create the tooling axis Design the class B and class C surface by class A surface Make a Soild body from Surface Design the required dog house and analysis them Perform the draft analysis for the final component GIVEN CLASS A SURFACE: CREATE TOOLING AXIS: For this…

AIM Create the Door trim lower plastic component through the given Class A surface. Also to create heat stakes and locators considering all the design rules. OBJECTIVE Create Tooling axis for the given Class A surface. Create the Class B and Class C surface of the door trim using the given Class A surface. Create final…

AIM     To create A pillar design with given master section Objective To create class B and C Surface To do draft analysis To create a dog house according to give master section and   following design rule To perform draft analysis A Pillar    It is a vertical structural support located…

AIM: To develop a Door trim panel from the given class A and master sections and also create the attachment features OBJECTIVE: To create individual tooling axis for the parts and perfrom draft analysis on the class A surface. To createnthe class B and class C surface from the given class A surface. To form a solid geometry…

HOOD DESIGN INTRODUCTION:- The car hood, also known as the bonnet, is a crucial part of a car's bodywork that covers the engine compartment. The hood is typically located at the front of the car and is attached to the vehicle's chassis by hinges, which allow it to be lifted for engine access. The hood is usually made of…

AIM:     To find section modulus calculation and optimization SECTION MODULUS     The section is a geometric property of a cross-section that is commonly used in structural engineering to analyze the bending behaviour of beams and other structural members.It is defined as the ratio of the…

AIM:    Calculate the wheel arch gap at required points and check whether the car passes the European standard FENDER   The fender is also known as a car wing or car quarter panel is a protective panel that is typically made of metal or plastic and is located on the exterior of a vehicle near the wheel wells…

Introduction Of car fender   The fender is a crucial component of a car' body design , serving as a protective covering for the wheels and tries. It is typically a curved metal panel that is strategically positioned over each wheel , extending from the front to the rear of the vehicle .Fender not only enhance …

   ROOF DESIGN  Introduction Of Car Roof    A car roof is the uppermost part of a vehicle that covers the interior and passengers from the elements . It is essential component of a car's structure that provides support and aerodynamic stability. Over the years, car roof designs have advances ,…

INTRODUCTION:  Back doors are an integral part of vehicles providing acess to the rear seating area or cargo space.they are typically hinged and located at the rear of the vehicle.Backdoors can be founds in various types of cars including sedans,SUVs,hatchbacks,and vans.They are designed to be opened and closed easily,…

Download the connector and connector clip cad file from given link Upload the cad files on the part design workbench Now identify and the connector connecting side and bundle connecting point Make a centre point on the both side by using point command Now placed the axis system on the connector side point Here Yaxis direction…

  PROCESS Download the cad file of P clamp from given link Upload the cad file in catia v5 part design workbench Create two point on both entry and exit center side of the P clamp Create 3 planes on the P clamp at center of entry plane , center of exit plane and bottom base plane Now open electric part design Click…

AIM: To route the following harness layout in the Electrical workbench Add the protective covering to all branches GIVEN:    CAD Data of the connectors DT06-4S DT06-6s DT06-2S DT06-08SA    Layout Design      STEP 1: Download the connector CAD data from given link    STEP 2:…

AIM: To create the assembly wiring harness as per given route mapping Check the bundle continuity Add annotation to all connectors Check for the bundle warning Generate CAT.part off harness assembly and convert is in .igs format GIVEN:      ROUTING MAPPING    CREATING THE ASSEMBLY WIRING HARNESS…

AIM:      To flatten the wiring harness and Draft the wiring harness assembly. Given: STEP 1: Defining Harness Flattening Parameters as shows in below fig  STEP:2 Now import the harness assembly to the Harness flattening workbench by using extract command. Now the Assembly name is end with EHF…

AIM :     To route the wiring harness on given engine and prepare flatten view drawing in CATIA V5 .Application of all packaging rules and industry best practices .Apply protection coverings as required.  INTRODUCTION OF WIRING HARNEESS:   It is a collection of wires bundled together and enclosed…

Aim:     To route the wiring harness on the given backdoor assembly and prepare the flatten view drawing in catia V5 Introduction:    Car tailgate wiring refer to the electrical system that connects various components located in the tailgate of a vehicle.The tailgate wiring is responsible for powering…

Aim To create a CATIA parametric structure with publication command PRODUCT FILE CREATION   Below images are which created the product and parts file in lens design. The given Class A surface of lens model.

1 Define tooling direction Tooling direction refers to the specific direction in which the components of a mold, such as the core and cavity, separate from each other during the molding process. It determines how the mold opens or pulls apart to allow for the ejection of the molded part. The tooling direction is an essential…

Design and modeling the Complete Tail lamp of the  Car   Aim:   To create the a complete design of the tail lamp with all the assembly parts and child parts, also the attachment features by considering the design regulations  in CATIA V5 Modelling Software. Introduction of Car exterior lights Car exterior lights are a…

Create the Plastic component as per the given sections. 

1 The full form of OEM is Original Equipment Manufacturer. 2  Concept design: This is the stage where the overall look and feel of the vehicle is determined. The automotive designer will work with a team of engineers and other stakeholders to develop a design that meets the needs of the target market and complies with…