ANS CALCULATION OF M35 GRADE OF CONCRETE WITH FLY ASH -DATA Grade of concrete = M35 Type of cement =OPC 43 Type of mineral admixture = Fly Ash Max size of aggregate = 20mm Min cement content = 320Kg/m3 Max water/cement ratio = 0.45 Workability = 100mm Exposure Condition = severe Max cement content = 450Kg/m3 Admixture…

ANS This all drawings are done by coordinates system. UNITS- Decimal in the coordinate system we have to take a distance form origin of the drawing COMMANDS USED IN ALL DRAWING - LINE - CIRCLE - UN FOR UNITS PROSEDURE FOR DRAWING -First take a one point for origin like (0,0),(1,1) etc. -after that masure the distance of…

ANS     AIM- 1- TO DRAW THE CROSS SECTION OF LOAD BEARING WALL OVER SPREAD FOOTING      2- TO DRAW THE CROSS SECTION OF ISOLATED FOOTING. 3- TO DRAW LINE DIAGRAM OF TWO BEDROOM BUILDING. 4- TO DRAW CROSS SECTION OF A LOAD BEARING WALL SHOWING FOUNDATION           …

QUE- DRAW THE GIVEN FIGURES.   FIGURE-1 AIM-TO DRAW FIRST FIGURE GIVEN IN ATTACHMENT. COMMAND USED IN FIGURE -1 LINE CIRCLE DIMSTYLE UNITS PROCEDURE FOR DRAWING -1 Open Autocad And Set the Decimal Precision to 0.00. take Line Command And Draw The line of 1.5 and another line of 1.5 in x direction. take next line at…

ANS-1 INTRODUCTION:- in the figure they give a residential plan of 25' x 43' 6.5" . in the plan they inclued parking,living,kitchen,two bedrooms with atteched bathroom .all the dimensions are in feet and inches. AIM:- Sketch the layout of a residence as shown in the Figure. COMMAND USED IN SKETCH:- XLINE (VERTICAL/HORIZONTAL)…

FIGURE-1 CREATE A COLUMN SCHEDULE AS SHOWN IN FIGURE. AIM:- TO CREATE A COLUMN SCHEDULE AND DRAW THE COLUMN REINFORCEMENT OF COLUMN IN DETAILS. COMMAND USED IN FIGURE:- limits singel text line trim circle rectangular offset mirror dimmension tool. extend PROCEDURE:- first open autocad and set limits and set units by unit…

QUE-1 : Draw the elevation and details of a wardrobe as shown in the Figure below. After sketching, you need to provide the dimensions and text with the use of layers. Use proper text styles and dimension methods to document it. Also, assume dimensions, wherever needed. Note: All dimensions are in mm. AIM: TO DRAW ELEVATION…

QUE-1 Create the Plan and Sections as shown in the Figures. Use proper dimension techniques and dimension styles to document the project. Assume the sizes of the doors and windows as per construction standards. Refer to sections for stair details if required. FIGURE - 1 AIM:- TO CREAT THE PLAN AND SECTION AS GIVEN IN FIGURE.…

QUE:- Design and Draft a layout of a residential building with the following details: a. Plot Size: 60’x20’(18.3m x6m)  b. Orientation- Facing East    c. Develop the following: 1. Architectural Drawing (Floor Plan, Elevations, and Sections) 2. Structural Drawing (Column, Bean, Footing Plan)  …

Q-1 Create the templates as shown in Figures. Take the size of the title block as per industry standards or you can assume it as per the size of the paper. Use text and attributes wherever required. After creating the title block you need to save it as a block with names: Custom1_titleblock and Custom2_titleblock, respectively.…

QUE-1 Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. Assume the size of doors, appliances and others as per the standards. AIM- create kitchen layout and give hatches pattern to the layout. COMMAND USED IN FIGURE 1:-…

QUE-1 Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use ATTEDIT command to edit the information in the title block. Use A1 size for the layout.…

QUE-1  Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing. AIM: To Create 3D Furniture element in autocad 3d using various tools. COMMAND USED :- line rectangular ucs extrude substract 3dface 3dorbit move copy PROSEDURE:- first open autocad and set units to the engineering. after…

QUE-. Create a 3D Isometric View of the building with plan and elevation given. ANS-1 AIM:- TO CREATE A 3D ISOMETRIC VIEW OF THE BUILDING WITH PLAND AND ELEVATION AS PER GIVEN DATA COMMAND :- unit line hide 3dorbit solidedit copy move join explode extrude union substrac material rotate PROSEDURE FOR DRAWING:- first open…

PROJECT-2 AIM:- TO CREATE A 3D RENDERED MODEL FOR A RESIDENTIAL BUILDING IN AUTOCAD. COMMAND USED IN THIS DRAWING :- unit line rectangular layer join explode extrude substract copy move solidedit hide 3dorbit ucs 3dface union PROSEDURE FOR DRAWING:- first open autocad set limits and units. now using line and other commands…

QUE 1) : From the file menu, create a new project (Structural / Architectural / Construction template ) and name the project appropriately. ANS 1- AIM- to create new project file for (structural/architectural/construction) from the file menu. PROSEDURE: first open revit software. now from the left side menu select…

Q-1) What is BIM? Summarize the features of BIM and benefits of using BIM over 2D CAD tools.   ANS-1 BIM is known as building information modeling or building information management . BIM is use for civil , architectural and also for a mechanical for detailing. Benifits of using BIM is it's provide lots of help for…

1) Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with grids created from…

QUE-1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level. ANS-1 AIM:-  TO CREATE CEILING FROM THE ARCHITECTURE TAB AT THE FIRST FLOOR. PROSEDURE:- to create a ceiling first open last project we did in…

1) Why are building codes or standards essential for the modeling/ efficiency of drawings in Revit ? ANS-1 the national building code (NBC) is the standards for construction of any building.NBC is followed by authorities and gov firms. main aim of NBC is provide saftey and standards.NBC provide details of fire and saftey,vantilation,design…

1) Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project ANS:- 1 AIM:- TO GIVE A SHARED COORDINATES FOR THE PROJECT. First open architectural template in revit . now go to the grid option . now create a grids like this. now go to the manage tab and…

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School ANS- I select Multi-Unit Residential Apartment.   2) Assume reasonable assumptions for geographic…

1) What are HVAC systems? Why are they essential in the modeling of buildings. ANS- HVAC Means Heating,Ventilation,AirConditioning.They are systems that Keep structure or building warm,cool as per session.They also clean and filter indoor air to keep us healthy and safe.now it's a common to use a central AC in big houses…

1) Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below           a. Using 3D model create a section box           b. To create similar doors and windows in a floor plan layout         …

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. ANS- AIM- TO CREATE SET OF SINUSOIDAL POINTS AND CREATE CURVE & SURFACE. PROSEDURE- first open revit . in revit under the manage tab we have a option of dynamo click on it. in dynamo click on create new…

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class. ANS- AIM- TO EXPORT NWC FILE FROM REVIT ARCHITECTURE. PROSEDURE- first open last project of revit. now in file…

ANS - 1(A) Observations: concrete crushed and the reinforcement is exposed. concrete spalled beyond the reinforcement which may be a sign of rupture. The crack develops fro bottom to top means rebar yielding occurs in support bottom only. CAUSE OF FAILURE: Its form of flexural failure due to reversal of stress during earthquake.…

Question 1: Compute lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The system has 3 DOFs as shown. Assume L = 2h and Elb = Elc   ANS u1=1 stiffness coefficient of column translation = 2x12EI/h^3 Stiffness coefficient of beaam rotation = EI/h^2   u2=1 stiffness…

ANS: Mass matrix (m) = `[[m,0,0,0,0],[0,m,0,0,0],[0,0,m,0,0],[0,0,0,m,0],[0,0,0,0,m]]`   Modified mass matrix (M) = `phi`n^t . m . `phi`n   For the first node (n=1) = [0.334  0.641  0.895  1.078  1.173]                     …

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. ANS-1 Investigation of the framing plan with respect to symmetry in…

Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account…

ANS- AIM- TO CREATE 25 STOREY BUILDING IN ETABS AS PER GIVEN DATA PROSEDURE- First open ETABS  now create new model option. after opening set units as per Is . next step is creating grids. create grids as shown below within given data use 4m distance . now we have to create a 25 storeys. in next step we have a option…

ANS- AIM- TO STUDY AND COMPAIR THE RESULTS ON Factors influencing the dynamic characteristics of a building Factors influencing the Natural Period of a building Factors influencing the Mode shape of oscillations Introduction:- The importance dynamic characteristics of a building are the modes of oscillation and damping…

Detail design of beams in Etabs 2018.The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span continuous beam along grid A       …

Reinforcement detailing of columns in Etabs 2018. The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment Resisting Frame. The following challenge deals specifically with two columns at the following grid intersections. 3A 3B Provide details of longitudinal reinforcement for the two columns,…

The etabs file for a G+6 building is provided. Run the analysis and design the RCC shear walls (show in the etabs model). The following challenge deals specifically with the shear wall of size 300x1500 at grid A-11 in the structural model. Extract values of longitudinal steel ratio, boundary element length and shear reinforcing…

ANS- AIM- TO CREATE A G+7 RESIDENTIAL MODEL FROM THE GIVEN ARCHITECTURE  DRAWING USING ETABS. PROSEDURE- open etabs software. click on new model. set model information. set units. now set grids as per shown below. now go to storey add option. set the storey as per requirment. model will look like this. now go to define>material>add…

AIM - provide Sufficient anchorage for column steel into the footing to provide sufficient depth and longitudinal steel for resisting bending and shear PROSEDURE - GIVEN DATA  Size of footing = 400x400mm soil bearing capacity = 150 kn/m^2 compression axial load = 2000 kn concrete grade = M25 STEP 1. SIZE OF FOOTING…

1. Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. ANS AIM:- TO MODEL THE ISOLATED FOOTING FOR PRIVIOUS CHALLANGE IN SAFE. PROSEDURE:- first open the SAFE set up a new model set prefrance, cover etc. for referance…

ANS- AIM:- DESIGN AND ANALYSIS A HOTEL BUILDING IN GUWAHATI , ASSAM USING ETABS AND SAFE. PROSEDURE:-  open ETABS and set the grid and storey data as per given in attachment. now edit storey . now go to define>materials. add M25, HYSD415, HYSD500. Now go to define>add section . add column of 400x600 and…