Calculate the Concrete Mix Design for M35 grade concrete with fly ash & M50 grade concrete without Fly ash   Ans 1.  A. Concrete Mix design for M 35 grade concrete with fly ash Stipulation for proportioning   Grade designation M 35 Type of Cement: OPC 43 grade conforming to IS 8112 Type of Mineral admixture:…

Sketch a G+1 floor residential plan, according to Vaastu Shastra, and list down the names of the structural drawings required to be provided to the site for construction. Also, assume the sizes of the structural elements (Column, Beam, Slab, etc.,) and accordingly calculate the individual corresponding loads from the members…

Create the geometries from P1 to P2 using all the coordinates system methods. You need to use the Line tool to create the geometries. Where required you need to use the circle tool. Please read the drawings and find out the missing dimensions before working on the sketches. Note: Use the Imperial Template and the Decimal…

  FIGURE C1 AIM: To draw the cross section of load bearing wall over spread footing and steps as shown in figure of attachment C1. Below is the final figure drawn to refer the point A, B, C… etc as mentioned in the procedure followed   PROCEDURE: Open new drawing. Quickset up the drawings to Metric system.…

CHALLENGE 3: Drafting of various geometries given in attachment from 1 to 11 using chamfer, fillet tool in AutoCad. FIGURE 1: AIM: To draft the given geometry in the figure 1 of attachment using various tools required to complete the figure in AutoCad. PROCEDURE: Set the drawing to Decimal units. Set the drawing limits…

Residence Plan: Sketch the layout of a residence as shown in the Figure 1. Consider all dimensions as reference to sketch the unit plan. Also the text in the layout are only for reference. Assume the missing dimensions. Also, refer the schedule for size of the doors. SOLUTION- 1 : AIM: To draw the sketch of layout of residence…

1.Create a column schedule as shown in the figure. Note: Create a column schedule with the help of lines. Also, insert text with the help of Dtext command or Single Line text. Hint: Use font name: romans.shx; Height: 8”, Justify: Left Challenge 1.  AIM: To create column schedule by drawing table and entering…

1. Draw the elevation and details of a wardrobe as shown in the Figure below. After sketching, you need to provide the dimensions and text with the use of layers. Use proper text styles and dimension methods to document it. Also, assume dimensions, wherever needed. Note: All dimensions are in mm. SOLUTION 1: AIM: To…

AIM:  To create Plan and Sections given in the figure in AutoCad using various drafting tools and using proper dimension techniques as per the given drawing showing the doors and windows of proper sizes as per construction standards. PROCEDURE: The procedure of drafting the Plan and Sections is given below along…

AIM: To Design and Draft a layout of a residential building with given details INTRODUCTION: Given details  Plot Size 60' x 20' ( 18.30m x 6.00m) Orientation- Facing East Drawing to be developed Architectural drawings          a. Floor Plan         b. Elevation    …

1. TEMPLATES AIM: To draft and create the templates of title blocks in the given figure using the text and attributes. INTRODUCTION: The two templates of title blocks as per the given figures are drafted assuming the paper size. The text and attributes commands are used along with other drawing tools to complete the…

1.Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. Assume the size of doors, appliances and others as per the standards.   Ans:  AIM: To create the layouts of the Kitchen and provide hatches pattern as shown…

1. Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use ATTEDIT command to edit the information in the title block. Use A1 size for the layout.…

1. Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing. Ans1: AIM: To create a 3D furniture element as given in the figure and providing dimensions for same using various 3D drawing tools. PROCEDURE: Open a new drawing. Set the scale to imperial and Engineering units Change the settings…

1. Create a 3D Isometric View of the building with plan and elevation given. Ans1: AIM: To create a 3D Isometric View of the given Building plan and elevation using various 3D drawing tools in AutoCad. PROCEDURE: Open a new drawing with Imperial units and set the drawing settings and Architectural drawing units and setting…

AIM: To create a 3D model of a residential building with rendered view in AutoCad using various 3D drafting tools. PROCEDURE:  Open a new drawing sheet and set up the drawing units to Metric and decimal. Set up the drafting settings  The available floor plan of a 3BHK residential building with Staircase and Lift…

1) From the file menu, create a new project (Structural / Architectural / Construction template ) and name the project appropriately Ans 1:  AIM & INTRODUCTION: To create a new project from the file menu and provide the name to the project in Revit.   PROCEDURE: Open the Revit program From the main page…

1) What is BIM? Summarize the features of BIM and benefits of using BIM over 2D CAD tools.  Ans 1: BIM is a visual representation of the physical and functional characteristics of a facility from inception onwards. As such, it serves as a shared information repository for collaboration throughout the facility’s…

1) Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with grids created from…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level Ans 1.  INTRODUCTION: Creating ceiling from architectural tab AIM: To create a model of ceiling from the architecture tab above walls at the first floor…

1) Why are building codes or standards essential for the modeling/ efficiency of drawings in Revit ? Ans 1. The building codes or standards provide the guidelines to design and construction the building so that all the parts or rooms of building are habitable, safe and serviceable. Building codes and standards provides…

  Ans 1 to 9. INTRODUCTION: Usage and application of Collaborate tool in Revit. AIM: To learn and apply the usage of the Collaborate tool in revits to create different templates for Architectural, Structural and Construction and collaborate the same using Copy/ Monitor tool PROCEDURE: Based on the questions 1 to 9…

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School Ans 1. The selected building structure is a Multi-unit Residential Apartment Parking + 6 floors…

1) What are HVAC systems? Why are they essential in the modeling of buildings Ans 1. HVAC systems consists of Heating, Ventilation and Air conditioning systems. It is part of indoor facility of the building. It helps maintain the temperature inside the building It helps maintaining the air quality in the building It reduces…

1) Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below           a. Using 3D model create a section box           b. To create similar doors and windows in a floor plan layout         …

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. Ans 1. INTRODUCTION: Creating surface from the curve created from sinusoidal points using Dynamo AIM: To create a set of sinosoidal points and creating curve and as surface out of the curve using Dynamo PROCEDURE:…

  1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class Ans 1. INTRODUCTION: Exporting the Revit model to Navisworks Cache file AIM: To export the Revit Structural…

AIM: To identify the types of cracks from the given pictures for awareness of structural failures, distinguishing structural and non-structural cracks, observing the structural issues and understanding Seismic failures. Ans 1.a.  Observations: From the picture 1 it is observed that the concrete of beam is crushed…

Differentiate Static analysis and Dynamic analysis with proper representing pictures (30 marks) Ans 1.  When loads and displacements are applied very slowly to a structure the inertia forces which are equal to mass and acceleration are negligible and may be disregarded in the force equilibrium. This load or displacement…