The list of structure drawing tha is mandatory to be provided to the site for constuction as fllowing center line drawing  footing and colun layout with reinforcement detailing column schedule with layout  plinth beam layout with reinforcement detailing ground floor slablayout with reinforcement detailing…

Mix Design For M35 Grade Of Concrete The mix design for M35 Grade Of Concrete for pile foundations provided here is for reference purpose only. Actual site conditions vary and thus this should be adjusted as per the location and other factors. Grade of Concrete : M35Characteristic Strength (Fck) : 35 MpaStandard Deviation…

Aim : To creating a floor plan, footing detail ans isometic view using autocad Part 1: Cross-section of load bearing wall over spread footing procedure:  type rec and press enter for activating the rectangle command specify the first corner rectangle enter D for dimensio  enter the width 0.90 enter the widtho.25…

Aim: To draw the geometries using chamfer, fillet tool in AutoCad Commands: Line,Circle,Chamfer,Fillet,Mirror,Trim,Move,Rotate,Annotate Procedure: Part-1 New sheet- units-decimals-precission 0.00-meter-ok limits-0,0and420,210 Z-enter,A-enter for zoom all select line tool and draw the lengths starting from base of 3.00…

AIM:- Sketch the layout of a residence as shown in the Figure 1. Consider all dimensions as reference to sketch the unit plan. Also the text in the layout are only for reference. Assume the missing dimensions. Also, refer the schedule for size of the doors PROCEDURE:-  Open auto cad, first set units(inches) and limits:…

AIM :- TO DRAW RESIDENTIAL BUILDING OF DIMENSIONS  60’ X 20’  WITH THE FOLLOWING 1)ARICHITECTURAL DRAWING PLOT DRAWING GROUND FLOOR PLAN FIRST FLOOR PLAN ELEVATION PLAN     2)STRUCTURAL DRAWING SECTION VIEW FOOTING LATOUT COLUMN LAYOUT BEAM LAYOUT INTRODUCTION:- THE RESIDENTIAL…

AIM:- to create the plane and section as shown in figures. Use proper dimensions techniques an dimensions styles to document the project using AutoCAD Commands used  Line rectangle trim offset dimensions layers text Procedure:- step:1 in the command prompt type units>mm. in the command box type limits>100,100 …

AIM : TO CREATE THE TEMPLATES BY USING AUTOCAD TOOL IN THIS TEMPLET NAME OF PROJECT CLIET NAME CONRACTOR NAME TIPE OF DRAWING DRAWIMG TEMPLATE NUMBER NUMBER OF THE REVISION DRAWN BY CHECKED BY RECHECKED BY ETC.., ARE MENTIONED PROCEDURE: OPEN AUTO CAD THEN CHANGE THE UNITS AS WE REQURED TYP ‘UN’ IN COMMAND…

AIM: To create the layouts of the Kitchen and also provide proper dimension techinques to dimensions the kitchen layout .Also, insert tex wherever required. STEP: in comand box type rec and press entergive dimensions are 473x3688mm in command box type offsetand press enter and draw the same images at a distance…

AIM 1 : To draw the elevation and details of a wardrobe as shown in the figure. after sketching,you need to provide the dimentions and text with the use of layers PROCEDURE: Step 1: units are set to mm limits and limax are also set zoom all  Step 2: in the command line type rec>2800,2600 in the command bar enter…

AIM: To create the given geomwtries and trusses in AUTOCAD, using the different co-ordinates system method and the line and circle drawing tools Geometries P-1 and P-2 drawn by using all coordinate system, and each of the remaing geometries are drawn using any one of the coordinate system or the ditect distance entry method.…

AIM 1:- To Create a column sechedule as shown in figure. Steps: Open AutoCAD and enter UN in command box and select enginnering and precision as 0'-0.000" Enter the limits in command bar and set the limits as we required Then zoom all enter Select line command and draw a line of84'in x-direction and a line of 21' in y-direction…

AIM : To create layout of plane and section , creating the viewpoint ,editing attributes and taking a plot. To cteating  a kitche layout in A4 sheet and take a plot. To create multiview ports for industrial section drawing ,scaling it and taking a plot. COMMANDS USED: view layout mulitiple view model space paper space…

AIM : To create 3D model and view of: Furniture element Isolated footing AASTHO type girder Drop column with panel A wall COMMANDS USED: Extrude offset UCS Box Union Subtract Move 3D orbit Loft Sweep Region Boundry PROCEDURE: Open the autoCAD click on the workspace switching and change it to 3d modeling and click on the…

AIM 1: To create a 3D isomwtric view of the given building with plane and elevation INTEODUCTION:- An isometric drawing is a 3D representation of an object,room,bilding or desing on 2D surface. One of the defining characteristics of an isometric drawing,compared to other type of 3D representation,is that the final image…

AIM : To create a 3 dimentional model of the residential builiding with rendered view. INTRODUCTIO: 3D computer-generated images of proposed builiding and other type of constructions are widely used by architects and designed to showcase their designs to clients. The steady advancement in computer graphic has enable the…

AIM 1:  To create a new project and name it appropriately INTRODUCTION: The product illustrates the creation of a new project file in Revit an naming the project file. PROCEDURE: STEP 1: Go to START MENU, click on Revit 2021. In the Rivet Home page click on new under the models option. In the New project dailog box,select…

1) Wht is BIM?Summarize the features of BIM and benefits of using BIM over 2D CAD tools A) Building information modeling (BIM):- Bim is an acronym for Building information modeling or building information Management. It is a highly collaborative process that allows architects,engineers,real estate developers,contractors,manufactures,and…

AIM 1:- To create a floor plan and need to apply the materials and thicknessusing the property browser. To align the floor plan with grid created from week 2. INTRODUCTION:- Building material is used for construction.Many natirally occuring substances,such as clay,rocks,sand and wood,even twings and leaves, have been used…

3D Creation of ceiling, Roof, Architectural plan, Sectional view, Elevation view and Camera specific view for house plan using the REVIT INTRODUCTION:-  Inorder to create the ceiling and roof for a building using revit software following steps can be followed: Ceiling: Open revit software àArchitecture tab…

1Q)Model codes allow building suppliers to target a national market. Since markets for building materials and technologies are becoming increasingly international, U.S. manufacturers require a strong domestic base in which to develop the new products they need…

INTRODUCTION:- Revit provides several different ways to collaborate with team members who are using the software. Several multiple model can be linked together, allowing team members to work in context. Through work sharing, user on same local area network can work together in the same revit model. When collaborate needs…

1Q)HVAC systems are very important during the architectural design of a building for the following reasons: The success of an HVAC system is directly related to the building’s comfort levels. HVAC systems require substantial floor space for housing the unit/units as well as the distribution equipment. Commercial HVAC…

1Q)Select the type of structure you want to build from one of the three below: Residential: Areas designated for single-family homes Commercial: Areas designated for businesses like restaurants, retail shops, and so on Industrial: Areas designated for factories Rural: Areas designated for farming Historical: Areas…

1)Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below a)Using 3D model create a section box-BX b)To create similar doors and windows in a floor plan layout-CS c) To reduce the thickness the range of visibility in a plan view-VR d)To applyoverride settings to floor in the…

1Q) AIM: Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve PROCEDURE: Open revit, go to manage tab and select dynamo We get interface,after opening dynamo, search point in the search option and bring them on the screen Then search code blocks and bring them on…

AIM 1: To use the structural project file developed by us in the week 6to 8  export the Revit Architecture and structural model to nvisworks cache file. PROCEDURE: Open the revit and open the file which you have saved in the week 6 to 8 and go to file then export,NWC and save file as NWC formate. Now the exporting…

AIM 1: To identify the type of failure from the above figures. Failure due to the improper nominal cover to the beam, buckling of reinforcement provided in the bottom of the beam and crushing of concrete at the beam-column junction. This type of failure happens if the naminal cover for the beam is inappropriate and the…

AIM 1 : Compute lateral stiffness of te one story frame with an intermediate realistic stiffness of the beam. The system has 3 DOFs as shown. Assume L=2h and Elb =Elc . Lateral stifness of the one story frame: This structure can be analyzed by any of the standard methods, including momentdistribution. Here we use the definition…

  1.Symmertry: Having a look over the aspects of symmetry of the framing plan, it is observed that the distribution of mass, Stiffness is across the plan; it is observed that the distribution of mass, stiffness is across the plan. It is considered for one of the good Symmetrical aspects. This tends to reduce the horizontal…

Ans Q1): As the structure is more restrained it will be more shrinking, expanding and cracking. There will be more floor shrinkage and expanding in structure A whereas there will be minimum cracks in structure B and C. The shear walls in the structure also decide whether the floor vibration is more or less in the structure…

Q) Model a 25 storey building on ETABS 2018 with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. Structural Element Sizes  Beams : 300 × 400 mm Columns : 800 ×…

Aim: To Compare fundamental natural periods of buildings H, J and K. using ETABS Procedure: Building H:                                                                                                                                                          Step…

Aim: To Providing details of longitudinal and shear reinforcement for the two continuous beams using ETABS  Step 1: 1) After downloading the model given in the question, click the Concrete frame design tool in the ribbon tab. 2) Choose Select design combinations 3) Select the appropriate combination from the dialogue…

Answer: Aim: To Providing details of longitudinal reinforcement for the two columns from foundation to terrace level. Step 1:  1) Open a G+4 Etab file 2) Click the Concrete Frame Design tool 3) Select the Display Design Info option 4) Choose design output as Longitudinal Reinforcement Step 2: 1) After Selecting the…

Aim: Detailing of shear wall Procedure: Step 1: The provided ETABS model is analysed and the shear wall design is run as shown in the figure below. Step 2: The mentioned shear wall is labelled as P1. The design results of pier P1 is extracted as shown below. From the obtained results, it can be seen that a boundary zone…

ANSWER:-  Aim:- To model and analyze the G+7 residential building from the given architectural drawings using the ETABS 2018.  Introduction:- ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis…

AIM:-To Create and Analyse the given building in ETABS 2018, the structural model has to be prepared in accordance with IS 1893 and as per IS 13920. To design the pile cap and pile reinforcement details,Tie beam connecting the pile caps, to sketch the column reinforcements, to produce the framing plan and beam detailing…

QUESTION:1 Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. ANS: AIM: To Analyze and designthe isolated footing from week 11 challenge on SAFE To verify the size, depth and steel provided as per calculations. INTRODUCTION:…

Aim : To calculate the Dead loads and Model the Bridge in Staad.Pro and do the analysis Given data : Width of the bridge deck is 10.2m. Span of the bridge is 12m. Pier size is 2.5 m. diameter The seismic zone is Zone IV. Wind speed is 47 km/h Procedure: 1.Manual calculation of the sectional properties like area of the…

Analyze the following structural elements and validate the results A. Simply Supported Beam a. A Simply supported beam with two point loads symmetrically placed Span L = 20m c. Load P = 50kN each d. Both P located at 5m from each support Aim & Introduction To analyze the given element Procedure Result & Conclusion…

1.Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab thickness as per the design Brick wall load Roofing load finish load=0.5*24=1.2kN/m2 slab load will be generated within the software brickwall+cement plaster thickness 230mm, brickwall loadingGL-1st floor-0.23*20*3.2=14.72kN/m3…

Analyze and design a steel building to 10T CRANE as per IS standard code in TEKLA STRUCTURAL DESIGNER. Refer the attached plan and elevation. Provide bracings and moment connection for lateral stability. Consider dead, live, equipment and wind loading. Consider the brick wall loading for 150mm thick and 1.5 KN per sq m…

Aim: Model of a membrane roof with cables. The modeling, form-finding and create the cutting patterns to the structure.  Procedure: Create a new project and enablr form finding and cutting pattern options Internal .Assign the material as cable to the lines Select the nodes and assign hinge support A i th f t th bl…

1. Aim: Summarize the user interface in TSD Procedure: Project Workspace Open the Tekla Software and click on the New option. Now the project workspace will be visible Scene Content– Demonstrate the use of scene content Open the Tekla Software and click on the New option. Now the project workspace will be visible…

Create column properties for different types of pedestal members and model in the grids created as per the assignment 1 Create column properties for steel columns and model columns in the grid created as per assignment 1 Create beam properties and model primary and secondary beams on the ground floor open new file In browser…

QUESTION : 1 Create beam properties for First floor and model the beams ANS: AIM: To Create beam properties for First floor and model the beams PROSEDURE: STEP: 1 Go to TDS software Open the challenge 2 file STEP: 2 go to home tab < Manage Properties sets property set tab will appear < click on New < member <…

We shall be using a model from our S3D to demonstrate how the loads (AS 1170.2/NZS1170.2 ) are applied on each surface. Figure 1. Warehouse model in  S3D as example. Figure 2. Site location (from Google Maps). Table 1. Building data needed for our wind calculation. Location Happy Valley Road, Cabarlah, Queensland,…

AIM: Generate manual wind loading in the design report based IS code as per the following input Procedure: Given: Basic wind speed = 39m/s Terrain category 2 Based on the above calculations Vb 39 m/s terrain category 2 probable design life of structure 50 years class of structure AL =greater horizontal dist. =18 wall ratios…

1. Summarize your study for the bending moment, shear force and deflection diagrams for the elements of the model.Ans)Bending Moment: It refers to the internal rotational moments that cause a section to bend. In the case of a beam, it can becalculated as the algebraic sum of the moments about the section of all forces…

AIM: To Analyze and design a steel building to 10T CRANE as per IS standard code in TEKLA STRUCTURAL DESIGNER.Provide bracingsand moment connection for lateral stability.INTRODUCTION:PROCEDURE:open tekla software,under file click on new.from analysing the given plan,the column placement is decided.to go setting,check once…