Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo

1Q) AIM: Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve

PROCEDURE:

1. Open revit, go to manage tab and select dynamo
2. We get interface,after opening dynamo, search point in the search option and bring them on the screen
3. Then search code blocks and bring them on the screen and enter values.
4. Now search sliders in the search option and bring them on the screen ,set their values as 0 to 50 and 0to 100.
5. Give the inputs of both the sliders to the variables a and b in he code block,and the output of which are connected to x of all the three points by co-ordinates.
6. Introduce another code block and the name it as points height and gevi the variable as h, take anothe number slider,connect it
7. Output to the input of height and the output of the height is connected to z coordinate of middle of point by coordinates
8. If we make an increase in the number is slider we can see the inclined point system in the form of curve
9. to make it to curve introduce nurds by point and list on the coordinates to each input of list.create
10. Output of list is connected to the input of nurbscurve,we get a curve .
11. Now interoduce plane at parameter on to the interface and connect the output nurds to the inputof curve
12. In order to give input to the second input of take anothet code block and enter its values.
13. We get a sutface.Now introduce circle on to the screen,connect the output of plane parameter to their of circle.
14. Inorder to give radius create a code block and name its as phase+maths.sin
15. Give the inputs to the amplitude and angle using code block.
16. Connect its output to the radius of circle.

2Q) AIM: Create a conceptual layout of floor plan in dynamo . Using the tools available in dynamo link the lines to appropriate model elements in Revit by choosing the wall types and wall parameters. Make use of the sliders to slide through the height of the wall and length of the wall.

PROCEDURE:

• Open dynamo and search points from the search option and bring them on the screen.
• Give diffrent names to each point,Now bring number slider on the screen and name them x and y,set their limits 10to100.
• Connect the output of x and y to control point 1 followed by 2 and 3,now introduce line by start point end point on to the screen.
• Connect the output of point to the input of line by start point end point origin to start point end point to control.
• In the way connect all the points forming a layout,now introduce wall by curve on to the screen and its required input such as levels,height,wall type and curve.
• Set the wall type asgeneric 5'',followed by height as 10 to 40 using number slider.
• Now intriduce the list option and connect the output of line to the output to the curve.
• Then connect it output to the vurve.
• Go back to the revit screen,change the view to 3d, you can alter the jeight of the layout using the height otion,can increase or decrase it.

3Q)AIM:Create an array of model elements in Revit. Use dynamo to vary the properties of model elements by using the slider or code block

PROCEDURE:

1. Open revit and draw a rectanglar column,copy the same and place it beside the previous column.
2. Now copy the group of two columns and place them above the previous group forminga group of 4 columns.
3. Now go to manage tab an open dynamo.Search select model elements set rotation and bring them on the screen.
4. Now click on the select option and select all the four columns,you get a value.
5. Now insert code block and enter the angle, conect its output to the degree,We can see all the four columns have been rotate at an angle of 60.
6. Now insert number slider and connect it to the degree.
7. As we increase the cursor in number slidr we can see the change in revit screen in 3d.

4Q) AIM: Create a conceptual mass in Revit and develop a parametric column by dividing the surfaces and apply the concepts similar to used in parametric walkway modelling. Use triangular bent or square shaped panels to add finish to the parametric column

PROCEDURE:

1. Open Revit ,go to the file option and select families.Open conceptial mass from the family.
2. We get an interface,change the view to north view and increase the level to 10'.
3. Go to the floor plan view,we get an interface , select the spline option and draw,and change view to 3d.
4. Select the entire figure and click and create from, resulting model we get like this.
5. Now from the properties bar change the boundary to square or triangular , now go to the file option select families and select curtain wall patttern based.
6. In order to create circle select the centre point of any one side and draw a circle at that point.

5Q)AIM: Use Dynamo to work on developing a Parametric Stadium. List your parameters and use the visual programming approach to complete the modelling, You can use the concepts discussed in parametric high rise tower in class for reference.

PROCEDURE:

1. Open the revit,go o the dynamo and make 4 integer sliders and change their names,then insert code block and insert the command
2. connect the output of the level to input lrvel of code block,connect the output of floor to floor height to the input of floor hight
3. Now introduce the rectangle by width using code block and give inputs to its using code book.
4. Now we can rotate the figure by using cursor of top floor rotationand bottom floor rotation.