Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad
AIM :
TO CREATE THE TEMPLATES BY USING AUTOCAD TOOL
IN THIS TEMPLET
NAME OF PROJECT
CLIET NAME
CONRACTOR NAME
TIPE OF DRAWING
DRAWIMG TEMPLATE NUMBER
NUMBER OF THE REVISION
DRAWN BY
CHECKED BY
RECHECKED BY ETC.., ARE MENTIONED
PROCEDURE:
OPEN AUTO CAD THEN CHANGE THE UNITS AS WE REQURED
TYP ‘UN’ IN COMMAND BOX AND PRESS ENTER AND CHANGE TYPE OF UNITS TO DECIMAL AND PRECISION TOO 0.00 AND INSRTIO SCALE TO MILLIMETERS NEXT TYPE ‘D’ IN there are they going to nearly COMMAND BOX AND PRESS ENTER CHANGE DIMSTYLE AS BASE ON UNITS
COMMANDS USED IN THIS
UNITS COMMAND
DIMSTYLE COMMAND
LINE COMMAND
TRIME COMMAND
REC COMMAND
DIM COMMAND
OFFSET COMMAND
CIRCLE COMMAND
BLOCK COMMAND
INSERT COMMAND
ATTRIBUTE COMMAND
TEXT COMMAND
IN ABOVE THE DRAWINGALL LINES ARE DRAWN BY USING THE LINE COMMAND IN THE BELOW COMMAND SELECT
ALL THE TEXTS IN THE ABOVE DRAWN BY USUNG TEXT COMMAND DIM COMMAND IS USED TO GIVE DIMENTIONS TO THE DRAWING
TRIM COMMAND IS USED TO THE REMOVE THE UNWANTED LINES FROM THE DRAWING
REC COMMAND IS USED TO DRAW THE TABLES
OFFSET IS COMMAND IS USED TO CREATE A NOTHER OBJECT WITHT THE SAME DIMESIONS OF SAME OBJECT.
AFTER CREATING THE TEMPLATES ALL THE TEMPLATESS ARE CREATED AS BLOCKS BY USING BLOCK COMMAND
ALL THE BLOCKS ARE SAVED BY GIVING DIFFERENT NAMES TO DIFFERENT BLOCK
THE TEXT INSIDE THE BLOCK ARE EDITED BY USING ATTRIBUTES.
CREATED BLOCKS ARE SAVED IN THE INSERT TOL AND WE CAN INSET THE CREATED BLOCKS IN THE DRAWING BY INSERT COMMAND
AIM:
TO CREATED THE DOOR 1 AND 2 BY USING AUTOCAD TOOL
INTRODUCTION:
TWO DOOR TYPES ARE GINEN, BOTH WITH SAME DIMENSIONS. FIRST DOOR TYPE ALONG WITH DOOR HANDLE AND FRAME.SECTION DOOR TYPE IS NORMAL FRAME HANDLE AND DOOR FRAME
PROCEDURE:
OPEN AUTO CAD CHANGE UNITS AS WE REQUIRED , TYPE ‘UN’ IN COMMAND BOX AND PRESS ENTER
CHANGE UNITS TYPE ‘D’ IN COOMAND BOX AND PRESS ENTER CHANGE DIMSTYLE BASED ON THE UNITS
UNITS COMMAND
DIMSTYLE COMMAND
LINE COMMAND
TRIME COMMAND
REC COMMAND
DIM COMMAND
OFFSET COMMAND
CIRCLE COMMAND
BLOCK COMMAND
FILLET COMMAND
TEXT COMMAND
IN ABOVE THE DRAWINGALL LINES ARE DRAWN BY USING THE LINE COMMAND IN THE BELOW COMMAND SELECT
ALL THE TEXTS IN THE ABOVE DRAWING BY USUNG TEXT COMMAND, DIM COMMAND IS USED TO GIVE DIMENTIONS TO THE DRAWING
TRIM COMMAND IS USED TO THE REMOVE THE UNWANTED LINES FROM THE DRAWING
REC COMMAND IS USED TO DRAW THE TABLES
OFFSET IS COMMAND IS USED TO CREATE A NOTHER OBJECT WITHT THE SAME DIMESIONS OF SAME OBJECT.
DRAW THE DOORS HANDEL USING RECTANGLE COMMAND ,2- POINTS CIRCLE COMMAND AND TRIM COMMAND AS FOLLOWIS
THE FINAL DRAWING OF DOOR 1IS SHOWN IN RESULT
AIM :
TO CREATE THE DOOR TYPES 1TO6 AS SHOWN IN THE FIGURE BY USING AUTOCAD TOOL
INTRODUCTION :
TWO DOORS TYPES ARE GIVEN, BOTH WITH SAME DIMENSIOS, FIRST DOOR TYPE AS PROJECTION OR SHAPES ON TOP IT ALONG WITH DOOR HANDLE AND DOOR FRAME,SECOND DOOR TYPE IS NORMAAL FOUR DOBLE SWING DOOOR WITH HANDLE AND DOOR FRAME
PROCEDURE:
OPEN AUTO CAD THEN CHANGE THE UNITS AS WE REQURED
TYP ‘UN’ IN COMMAND BOX AND PRESS ENTER AND CHANGE TYPE OF UNITS TO DECIMAL AND PRECISION TOO 0.00 AND INSRTIO SCALE TO MILLIMETERS NEXT TYPE ‘D’ IN there are they going to nearly COMMAND BOX AND PRESS ENTER CHANGE DIMSTYLE AS BASE ON UNITS
COMMANDS USED IN THIS
UNITS COMMAND
DIMSTYLE COMMAND
LINE COMMAND
TRIME COMMAND
REC COMMAND
DIM COMMAND
OFFSET COMMAND
CIRCLE COMMAND
BLOCK COMMAND
BEDIT COMMAND
INSERT COMMAND
ATTRIBUTE COMMAND
TEXT COMMAND
DOOR 1
DRAW THE RECTANGLE OF DIMENSIONS 2’10”X6’11”
SELECT THE RECTANGLE DRAWING ABOVE AND TYPE EXPLODE(X) AND PRESS ENTER
SELECT THE TOP, RIGHT, LEFT EDGES AND TYPE JION(J) AND PRESS ENTER
OFFSET TO THE INSIDE ‘F’ RECTANGLE TO A DISTANCE1.5”
DRAW THE DOOR HANDELUSING THE RECTANGLE AND CIRCLE COOMAND AS SHOWING IN FIGURE.
DOOR 2
DRAW THE RECTANGLE OF DIMENSIONS 3'4"X6'11"
SELECT THE RECTANGLE DRAWING ABOVE AND TYPE EXPLODE(X) AND PRESS ENTER
SELECT THE TOP, RIGHT, LEFT EDGES AND TYPE JION(J) AND PRESS ENTER
OFFSET TO THE INSIDE OF RECTANGLE TO A DISTANCE 1.5"
OFFSET TO THE INSIDE OF RECTANGLE TO A DISTANCE 1"
DRAW A RECTANGLE OFFSET OF 1" TO INSIDE TWICE.
USING RECTANGULAR ARRY COMMAND DRAW THE FOUR ROWS AD THREE COLUMNS.
BELOW THE DRAW A RECTANGLE INSIDE TO THE DISTANCE OF 1"FOUR TIMES AND 1" TWICE
DOOR 3
DRAW THE RECTANGLE OF DIMENSIONS 2’10”X6’11”
SELECT THE RECTANGLE DRAWING ABOVE AND TYPE EXPLODE(X) AND PRESS ENTER
SELECT THE TOP, RIGHT, LEFT EDGES AND TYPE JION(J) AND PRESS ENTER
OFFSET TO THE INSIDE ‘F’ RECTANGLE TO A DISTANCE 1”
OFFSET TO THE INSIDE ‘F’ RECTANGLE TO A DISTANCE 2”
OFFSET TO THE INSIDE ‘F’ RECTANGLE TO A DISTANCE 1”
OFFSET TO THE INSIDE ‘F’ RECTANGLE TO A DISTANCE 1”
DRAW THE RECTANGLE OFFSET OF 1" FROM THE EDGES AND OFFSET YHE RECTANGLE 1" TO INSIDE
HATCH THE INNER RECTANGLE SIMMILAR TO THE DOOR TYPE 1
DOOR 4
DRAW THE RECTANGLE OF DIMENSIONS 2’10”X6’11”
SELECT THE RECTANGLE DRAWING ABOVE AND TYPE EXPLODE(X) AND PRESS ENTER
SELECT THE TOP, RIGHT, LEFT EDGES AND TYPE JION(J) AND PRESS ENTER
OFFSET TO THE INSIDE ‘F’ RECTANGLE TO A DISTANCE 1.5”
OFFSET TO THE INSIDE ‘F’ RECTANGLE TO A DISTANCE 1"
HATCH THE INNER RECTANGLE SIMMILAR TO THE DOOR TYPE 1
DRAW A RECTANGLE OFFSET OF 1" TO INSIDE TWICE.
USING RECTANGULAR ARRY COMMAND DRAW THE FOUR ROWS AD THREE COLUMNS.
BELOW THE DRAW A RECTANGLE INSIDE TO THE DISTANCE OF 1"FOUR TIMES AND 1" TWICE
DRAW A RECTANGLE OFFSET OF 1" TO INSIDE TWICE.
USING RECTANGULAR ARRY COMMAND DRAW THE FOUR ROWS AD THREE COLUMNS.
BELOW THE DRAW A RECTANGLE INSIDE TO THE DISTANCE O"FOUR TIMES AND 1" TWICE
TRIM THE CIRCLES
DOOR 5
DRAW THE RECTANGLE OF DIMENSIONS 3’4”X6’11”
SELECT THE RECTANGLE DRAWING ABOVE AND TYPE EXPLODE(X) AND PRESS ENTER
SELECT THE TOP, RIGHT, LEFT EDGES AND TYPE JION(J) AND PRESS ENTER
OFFSET TO THE INSIDE ‘F’ RECTANGLE TO A DISTANCE 1.5”
OFFSET TO THE INSIDE ‘F’ RECTANGLE TO A DISTANCE 1"
HATCH THE INNER RECTANGLE SIMMILAR TO THE DOOR TYPE 1
DRAW A RECTANGLE OFFSET OF 1" TO INSIDE TWICE.
USING RECTANGULAR ARRY COMMAND DRAW THE FOUR ROWS AD THREE COLUMNS.
BELOW THE DRAW A RECTANGLE INSIDE TO THE DISTANCE OF 1"FOUR TIMES AND 1" TWICE
DRAW A RECTANGLE OFFSET OF 1" TO INSIDE TWICE.
USING RECTANGULAR ARRY COMMAND DRAW THE FOUR ROWS AD THREE COLUMNS.
BELOW THE DRAW A RECTANGLE INSIDE TO THE DISTANCE O"FOUR TIMES AND 1" TWICE
TRIM THE CIRCLES
DOOR 6
DRAW THE RECTANGLE OF DIMENSIONS 3’4”X6’11”
SELECT THE RECTANGLE DRAWING ABOVE AND TYPE EXPLODE(X) AND PRESS ENTER
SELECT THE TOP, RIGHT, LEFT EDGES AND TYPE JION(J) AND PRESS ENTER
OFFSET TO THE INSIDE ‘F’ RECTANGLE TO A DISTANCE 1.5”
OFFSET TO THE INSIDE ‘F’ RECTANGLE TO A DISTANCE 1"
HATCH THE INNER RECTANGLE SIMMILAR TO THE DOOR TYPE 1
DRAW A RECTANGLE OFFSET OF 1" TO INSIDE TWICE.
USING RECTANGULAR ARRY COMMAND DRAW THE FOUR ROWS AD THREE COLUMNS.
BELOW THE DRAW A RECTANGLE INSIDE TO THE DISTANCE OF 1"FOUR TIMES AND 1" TWICE
DRAW A RECTANGLE OFFSET OF 1" TO INSIDE TWICE.
USING RECTANGULAR ARRY COMMAND DRAW THE FOUR ROWS AD THREE COLUMNS.
BELOW THE DRAW A RECTANGLE INSIDE TO THE DISTANCE O"FOUR TIMES AND 1" TWICE
TRIM THE CIRCLES
AIM :
TO CREATE THE BAR BENDING SECHUDLE BY USING AUTOCAD TOOL
IN THIS TEMPLET
NAME OF PROJECT
CLIET NAME
CONRACTOR NAME
TIPE OF DRAWING
DRAWIMG TEMPLATE NUMBER
NUMBER OF THE REVISION
DRAWN BY
CHECKED BY
RECHECKED BY ETC.., ARE MENTIONED
PROCEDURE:
OPEN AUTO CAD THEN CHANGE THE UNITS AS WE REQURED
TYP ‘UN’ IN COMMAND BOX AND PRESS ENTER AND CHANGE TYPE OF UNITS TO DECIMAL AND PRECISION TOO 0.00 AND INSRTIO SCALE TO MILLIMETERS NEXT TYPE ‘D’ IN there are they going to nearly COMMAND BOX AND PRESS ENTER CHANGE DIMSTYLE AS BASE ON UNITS
COMMANDS USED IN THIS
UNITS COMMAND
DIMSTYLE COMMAND
LINE COMMAND
TRIME COMMAND
REC COMMAND
DIM COMMAND
OFFSET COMMAND
CIRCLE COMMAND
BLOCK COMMAND
INSERT COMMAND
ATTRIBUTE COMMAND
TEXT COMMAND
IN ABOVE THE DRAWINGALL LINES ARE DRAWN BY USING THE LINE COMMAND IN THE BELOW COMMAND SELECT
ALL THE TEXTS IN THE ABOVE DRAWN BY USUNG TEXT COMMAND DIM COMMAND IS USED TO GIVE DIMENTIONS TO THE DRAWING
TRIM COMMAND IS USED TO THE REMOVE THE UNWANTED LINES FROM THE DRAWING
REC COMMAND IS USED TO DRAW THE TABLES
OFFSET IS COMMAND IS USED TO CREATE A NOTHER OBJECT WITHT THE SAME DIMESIONS OF SAME OBJECT.
AFTER CREATING THE TEMPLATES ALL THE TEMPLATESS ARE CREATED AS BLOCKS BY USING BLOCK COMMAND
ALL THE BLOCKS ARE SAVED BY GIVING DIFFERENT NAMES TO DIFFERENT BLOCK
THE TEXT INSIDE THE BLOCK ARE EDITED BY USING ATTRIBUTES.
CREATED BLOCKS ARE SAVED IN THE INSERT TOL AND WE CAN INSET THE CREATED BLOCKS IN THE DRAWING BY INSERT COMMAND
