Hello sir, I have already summited the previous design procedure of cavity block, core block, and sliders. After watching your week 7 tutorials. now, after watching tutorials,  I increased the slider part01 & slider part 02 by 10 mm. then I edit the cavity block and go to the insert command to insert slider 01…

Hello sir, DRAFT ANALYSIS, SCALE, PARTING LINES, SHUT-OFF SURFACE, AND PARTING SURFACE------- Opened the Plastic Component model and went to the Draft Analysis command then check the draft analysis of this model.After that, I went to scale command to scale this model (this material is ABS then the Shrinkage value of (0.6%…

Hello sir, I am working on the CPU fan case model, in this assignment, I have to create sliders, nuts, bolts, washers, locking mechanisms, inserts. Firstly, open the assembly of the CPU case model then I have going to create two sliders because two undercuts are present in the CPU case model. In this model, the core area…

Hello sir, The Step followed of making the week 12 challenge are......... Ejector pin Ejector plate Ejector backplate Sprue  Runner  Gate Air vents Cooling channel  I am going to make the ejector pin, ejector plate for the mold.I edit the core block and select the face and I draw a sketch (24) then go to…

Hello sir, The procedure of making the CPU fan Bezel (week 14) challenge are......... Draft analysis Scale Parting lines Shut-off surfaces Parting surface (using Ruled & lofted surface) Core & cavity surface Assembly Sprue Alignment Core & Cavity Block Reliefs Ejector pin Ejector plate Ejector backplate Sprue…

HELLO SIR,                               Week 8 - Challenge 1 - Draft Analysis on a Fan Cover DRAFT ANALYSIS OF FAN COVER First, I check the connectivity of the (Class A) Fan cover model. Click on the join command & boundary command to check, and to ensure that there is no gap between the surfaces. After that, Creation…

HELLO SIR,                                              Week 8 - Challenge 3 - Switch Bezel Design OBJECTIVE:- Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the…

HELLO SIR,                                       Week 8 - Challenge 2 - Base Bracket Design First, I check the connectivity of the (Class A) Base Bracket Design. Click on the join command & boundary command to check, and…

HELLO SIR,                                       Week 8 - Challenge 4 - Coin Holder Design First, I check the connectivity of the (Class A) Coin Holder model. Click on the join command & boundary command to check, and to ensure…

HELLO SIR,                                      Week 8 - Challenge 5 - Core & Cavity Design OBJECTIVE:- Create the Core and cavity blocks for the switch bezel A detailed report should be done explaining the draft analysis…

HELLO SIR,                               Week 9 - Attachment Feature Creation - Challenge 1 OBJECTIVE:-  Create the rib for the Centre console coin holder. (Use Positioned sketch & Sketches should be Iso-Constrained) A detailed report should…

HELLO SIR,                                        Week 9 - Attachment Feature Creation - Challenge 2 Objective- Create the boss and Dog House for the Centre console coin holder.   First of all, create the Class B &…

HELLO SIR,                 Week 9 - Project 1 - Door Applique Design with Engineering Features   OBJECTIVE:- Create the Door Applique Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting…

HELLO SIR,                                                                                Week 9 - Project - Master…

HELLO SIR,                                                Door Arm Rest Week 8 Challenge First, I check the connectivity of the (Class A) door arm model. Click on the join command & boundary command…

HELLO SIR,                                                               Week 10- Assembly Workbench  1. QUICK RETURN MECHANISM PART 1 FRONT, TOP , SIDE & ISOMETRIC…

                                 Week 1:- Introduction to BiW and Fixtures Challenge Hello sir, Q.no- 1. What is BIW & define its parts? In the Automotive Industry BIW (Body in White) is the common terminology used to mention the car…

                                                             Week 2:- BiW Fixture Basics Challenge Hello sir, Question No:-1.  What is the process of project…

                                              Week 3:- BiW Fixture Design Methodologies Challenges HELLO SIR, QUESTION NO:-01. What is Design Methodology? ANSWER:- Design Methodology is nothing but steps followed…

                                              Week 4:- Pin Unit Design Challenge QUESTION NO:- 1. Design 2 Different types of Fixed Pin Units with Different Pins, Riser, Blade, and Block. QUESTION NO:-…

                                 Week 5:- Rest Unit & Clamp Unit Design Challenge QUESTIONS: Design 3 Different types of Power Clamp Unit with Different Riser, Blade, and Clamp Arm for the given Car Panel. Design 2 Different types of Rest Unit for the given Car Panel. AIM/OBJECTIVE: In this challenge, we have to design…

                                               Week 6:- Clamp Unit & Pin-Clamp Unit Design Challenge AIM/INTRODUCTION/OBJECTIVE: In this challenge, we have to design 3 different types of swivel clamp with different riser, clamp, blade, and clamp arms for the car panel & design a pin-clamp unit also considering panel thickness…

                                                  Week 7:- Base Unit Design Challenges 1 QUESTIONS:- What is the Base Unit? What are the typical parts of the Base Unit? What are the points need to…

HELLO SIR,                                                            Week 11 - Final project   OBJECTIVE:- To design the following requirement for the given class A…

                                              Week 7- Base Unit Design Challenges 2 QUESTIONS:- To Design a base unit for the Pin Unit, Clamp unit, Swivel Unit, with all weldment for the car panel. ANSWER NO:- BASE UNIT is the unit designed to mount all the other units (clamp unit, pin unit, rest unit, etc.) of the tools,…

                                                     Week 8:- 3D Finishing - Challenges 1 QUESTIONS:-01 What do you understand by the 3D finish process? ANSWER:- 3D-Finishing: It is the…

                                                    WEEK 9:- 2D Detailing Challenge QUESTION NO:- 01 What are the Drawing templates? ANSWER:- Drawing Templates are the standard drawing files…

                                                Week 8:- 3D Finishing Challenge 2 AIM/OBJECTIVE:- Perform 3D finish for all units of Assembly design. Create Rough locators for Assembly.…

                                           Week 10:- 2D Detailing Challenge Aim: 1)Draft a Key Sheet for the Complete Fixture assembly created in challenge 8. 2)Draft a Base Unit and the Fix…

                                                 Week 11:- 2D Detailing Challenge 2 OBJECTIVE:- 1. Create a 2D Drawing for each Clamp Unit with all child parts and also create a Child pard…

                                                           Week 12:- Documentation Challenge OBJECTIVE:- Create a BOM and Hardware list (BOP) THEORY: …

                                                                           Benchmarking Question:- 1. Benchmark with presently available…

                                                           UNDERBODY COATING QUESTION:- Write a one paper about under-body coating and its purpose its types in detail, and…

                                                    Hood design-Week 2 Aim:- Design Hood Outer Panel, Inner Panel, and the necessary reinforcements by following the Master Section mentioned…

                                               Fender Design - Wheel Arch Challenge   AIM:- Calculate the Wheel Arch gap at required points and check whether the car passes the European standard. WHEEL ARCH:  The wheel arch is the semicircular part positioned above the wheel of a vehicle. The most important body change…

                                                   Fender Design Challenge    OBJECTIVE : The main object of this project is to design the BIW(Body in white) of front fender using…

                                                         Section Modulus calculation and optimization Aim : Use the Section from your Hood design and calculate the section modulus using the formula S = I/y. From the below images, the steps for calculating the section modulus for the given surface can be seen. In order…

                                                                Roof challenge   AIM: Design of the front roof rail, rear roof rail, and bow roof for…

                                                             Design of backdoor   OBJECTIVE: To develop the car backdoor by using the given Class A surface method by automotive sheet metal Design. BACKDOOR DESIGN The backdoor or tailgate is the rearmost part of the automobile which opens upwards, downwards, or sideways…

                               Sheet Metal Design Using NX Cad Challenge_1_Casing Design   Objective:- The report contains a detailed explanation of the sheet Metal Design of the Casing. The main objective of this course is to learn Sheet…

                                                    Challenge_2_Box Assembly   TITLE OF THE PROJECT: Advanced sheet metal design using Siemens NX cad - Box Assembly. OBJECTIVE: To…

                          Advanced Sheet Metal Design Using NX Cad Challenge_5_Odd Shaped Enclosure   OBJECTIVE:- To design an odd-shaped enclosure and create a draft of it using the Siemens NX Sheet metal application. INTRODUCTION:- Sheet metal is…

                               Advanced Sheet Metal Design Using NX Cad Challenge_6_Bracket   Objective: To design a Bracket using the Siemens NX Sheet metal application.   Introduction:-   SIEMENS NX:- NX formerly known as "Unigraphics",…

            Advanced Sheet Metal Design Using NX Cad Challenge_7_ Metal bracket-II   OBJECTIVE:- To design and model the sheet metal bracket-2 in NX-12 by using some basic features and tools. To learn how to design a sheet metal bracket-2 from a given drawing. To master the user interface…