“Motion Analysis of Internal Geneva Mechanism Using Solidworks”.   AIM: TO ANALYSE THE MOTION ANALYSIS OF INTERNAL GENEVA MECHANISM USING SOLIDWORKS.   OVERVIEW:                           The Geneva drive or Maltese cross is…

"Motion analysis of Planetary Gear Mechanism using Solidworks". 1. Aim: TO ANALYSE THE MOTION ANALYSIS OF A PLANETARY GEAR MECHANISM USING SOLIDWORKS. 2. Objective: To create an internal ring with the following properties:          Module = 2.5 (ANSI METRIC must be used while selecting Gear train).…

"Motion analysis of Piston Assembly using Solidworks". 1. Aim: TO ANALYSE THE MOTION ANALYSIS OF PISTON ASSEMBLY USING SOLIDWORKS. 2. Overview: A slider-crank linkage is a four-link mechanism with three revolute joints and one prismatic, or sliding, joint. The rotation of the crank drives the linear…

''Week-3 Challenge: ADVISOR Tool'' Aim: By using Advisor Tool we have to use simulate the following conditions. Objective:  1. For EV_defaults_in file, if cargo mass is 500 kg with all other default conditions, can the vehicle travel for 45 km with FTP drive cycle? Conclude your observations. 2. In the above case,…

"Week-4 Challenge WOT Condition Part-2" Aim: To study and perform the following condition by using Powertrain Blockset. Objective: To study the difference between mapped and dynamic model of engine, motor and generator.and also How can we change model type?  To describe how does the model calculate miles per gallon?…

"Week-6 Challenge: EV Drivetrain" Aim: 1.  To study different types of power converter circuits employed in electric and hybrid electric vehicle?    2.  An Electric Vehicle's powertrain with 72V battery pack in shown in the diagram below. The duty ratio for acceleration operation is 'd1' and…

"Week 3 - Solving second order ODEs".Aim: To write a program to solve a 2nd order ODE that represents the motion of a simple pendulum & also to create the animation of its motion.Objective:To write a program that solves the following ODE which represents the equation of motion of a simple pendulum with damping Where,g…

"Project 2 - Rankine cycle Simulator" Aim: To create a program for Rankine Cycle Simulator and plot T-S, H-S diagram. Objective: To create a Rankine Cycle Simulator. To write a program for calculating the state points of the Rankine Cycle based on user inputs. Plot the corresponding T-S and H-S diagram for the given sets…

"Week 4.1 - Genetic Algorithm" Aim:  To write a code in Matlab to optimize the stalagmite function and find the global maxima of the function. Objective: To write a code in MATLAB to optimize the stalagmite function and to find the global maxima of the function. To explain the concept of genetic algorithm…

"Project 1 - Parsing NASA thermodynamic data" Aim:  To write a Matlab Program to extract 14 coefficients from NASA Thermodynamics data file to calculate enthalpy, entropy, specific heat, for all the species in the data file. Objective: To write a function that extracts 14 co-efficient for a given species from the…

"Week-11 Challenge: Braking" Aim: To study braking and braking energy calculation by using Matlab. Objective:  To calculate the energy required for braking For a defined driving cycle. To study Why electric motor can’t develop braking torque at high speed similar to starting? Studying the…

"Week-7 Challenge: DC Motor Control" Aim: To study and understand DC Motor Control. Objective: 1. A. Explain a MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge’.     B. Comment on the armature current shoot-up from the scope results.     C. Refer to the help section…

"Project-1: Powertrain for aircraft in runways"  Aim & Objective:   Part A: 1. To search and list out the total weight of various types of aircrafts.  2. To find out that is there any difference between ground speed and air speed? 3. To justify why is it not recommended to use aircraft engine power to…

"Project 1 (Mini Project on Vehicle Direction Detection"   Aim: To identify the direction of the vehicle in Autonomous driving & Advanced Driver Assistance Features and develop the Simulink Model as per the requirement.   General Overview:                    …

"Project 2 Adaptive Cruise Control" Aim:To Develop an Adaptive Cruise Control feature as per the Requirement Document by using MATLAB Simulink.Objective of Main Project:Developing Adaptive Cruise Control feature as per the Requirement Document using MATLAB Simulink.Follow all the MBD related processes: Requirement Tagging…

"Final Project: Design of an Electric Vehicle"   Aim: To create a MATLAB model of electric car which uses a battery and a DC motor. Choose suitable blocks from Powertrain block set. Prepare a report about your model including following: Objectives:         1. System level configurations        2. Model parameters      …

"Week 1 Understanding Different Battery Chemistry" Aim: To understand about Different Battery Chemistry. Objective: To prepare a table that includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP, and LTO types of lithium-ion cells. To compare the differences between each type…

"Final Project: Electric Rickshaw modelling" AIM:  To create a MATLAB model of an Electric Rickshaw using a Lithium-ion Battery, Permanent Magnet Brushed type DC motor, a motor Controller, and various Powertrain block sets.  OBJECTIVES: Create a detailed MATLAB model of an electric rickshaw (three-wheel passenger vehicle)…

"Week 7 State of charge estimation" AIM:  To Study the State of Charge Estimation.   OBJECTIVES : Simulate the 3 test cases from the harness dashboard and write a detailed report on the results. What is coulomb counting? Refer to the above model and explain how BMS implements coulomb counting for SOC estimation.  State…

"Project 1 Mechanical design of battery pack"   AIM: To design a battery pack for 18kWh. OBJECTIVE: To prepare a detailed battery pack drawing along with its enclosure. Battery pack capacity: 18 kWh Cell: ANR26650M1-B  METHODOLOGY:  1) To build the Battery pack for any Electric Vehicle, we have to calculate…

"Project 2 Thermal modeling of battery pack" AIM:  To Study the Thermal Modeling of Battery Pack.   OBJECTIVES : For a 10-cell series lithium-ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, and charge & discharge rates using MATLAB.  …

"Final Project - Side Door Trim"   AIM & OBJECTIVES: Create the Door trim Panel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.…

  AIM & OBJECTIVE: To create the B-Pillar's Plastic component from the given Class A Surface using the Master Section that is provided while following all the design rules.   INTRODUCTION: Types of Pillars and their importance in the Automotive Industry:-   These pillars standing…

OBJECTIVE: To create the Base-Bracket's Plastic Component using the Class A Surface that is provided. Firstly, we have to create the required Tooling-Axis for the given Class A Surface while meeting the requirements of the necessary Draft Angle & then perform the Draft-Analysis Operation…

AIM & OBJECTIVE: To create the Bumper's Plastic-Component using the Class A Surface that is provided. Desired Thickness of the Plastic Component is 3mm with 3 degrees as the Draft Angle. Firstly, we have to create the required Tooling-Axis for…