CREATION OF MAIN TOOLING AXIS :   Bisecting Method   Steps followed :    1) Create a point at the center of hole of given surface.   2) Create a dummy tooling axis ,which will be reference for tooling direction.             3) Insert an axis…

  REPORT :                     TOOLING AXIS CREATION  : BISECTING METHOD STEP FOLLOWED : 1) Create a point on base surface 2) Insert an axis system at that point 3) Find the intersection of Z-X plane at the A-Class surface.Then find the bisecting line…

      CREATION OF MAIN TOOLING AXIS          :       Bisecting method      Step followed :     1) Extract the base surface     2) Create a point on base surface     3) Create a line from this point with appropriate…

                  CREATION OF MAIN TOOLING AXIS  :   POINT & DIRECTION METHOD     STEP FOLLOWED :   1) Extract a surface which is almost in mid of part and almost plane.   2) Create a point on this plane   3) Now create a line…

       REPORT :                     TOOLING AXIS CREATION  : BISECTING METHOD STEP FOLLOWED : 1) Create a point on base surface 2) Insert an axis system at that point 3) Find the intersection of Z-X plane at the A-Class surface.Then…

                    CREATION OF MAIN TOOLING AXIS                :    BISECTING METHOD    STEP FOLLOWED : 1) Create a point on the bigger hole / circle of the class-A surface. 2) Insert a axis system…

                                   CREATION OF MAIN TOOLING AXIS     :     BISECTING METHOD            STEP FOLLOWED  :         1) Extract a…

              CREATION OF MAIN TOOLING AXIS  :                                                                    …

                          CREATION OF MAIN TOOLING AXIS                                                        …

                              CREATION OF MAIN TOOLING AXIS   :                                            …

                                                                                   REPORT OF THE PROJECT  …

                                                                                    PROCEDURE FOLLOWED IN…

                                                                              FINAL PROJECT        …

            QUS  :  1  :                                  As we know there are five member in the family of Mr.D.S.Pughazhyendhii. He is fond of big car. He has drive in city and highway also , and budget is 8 Lakh to 10 Lakh. According to me he can go for following car :         1) Hyundai Aura SX  Plus 1.2  :        …

              Under-Body Coating  :  OR ED-Coating  :   ED-Coating means Electro-Deposition Coating which is also known as E-Coating. ED-Coating is a method of painting which uses electrical current to deposit the paint. The process works on the principle…

                                                                              AUTOMOTIVE HOOD DESIGN                 Projective  Objective  :     In this project we are going to design the front mounted engine's hood according to the standard . The hood or bonnet is the hinged cover over the engine of motor vehicle that…

                                                SECTION MODULUS CALCULATION AND OPTIMIZATION        OBJECTIVE  :  To calculate the section modulus for hood design in both direction , for front crash and side crash . After calculating the section modulus optimize it's value.      Section Modulus  :  Section modulus is a…

                                                               FENDER WHEEL ARC REGULATION                                                                                       When an automotive vehicle is running away then stone particle , dust particle and fluid particle is thrown away by the rotating tyres of vehicle.…

                                                                         FRONT FENDER DESIGN               OBJECTIVE   :   To design the front fender of a car from the given skin data by following the given master section.          FENDER   :     Fender is the American english term for the part of an automobile that frames…

                                                                        ROOF DESIGNING           Objective …

                                                                                           …

             Objective   :          To Create the assembly of all parts of butterfly valve and apply the GD & T on it's drafting.          Software Used  :        NX CAD  (UG)  …

         Objective   :             Download the part from given link and define these electrically , creating the catalogue of these part, and create assembly for connector and Clip.         Given Input  :        Download link is provided for all the parts ( Company  : Tyco Electronics )           Software Used  :     …

                                                          Wiring Harness routing and packaging rules week 3 challenge                …

                                                                                   Wiring harness design in CATIA…

                                              Wiring harness design in CATIA V5 - 3D modelling Week 5 & 6 Challenge              AIM   :  Create two…

                                              Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge     AIM   :    To prepare the flattened view of wiring harness…

                                                                         WIRING HARNESS DESIGN PROJECT 1       AIM…

                                                                                          …