AIM : To solve the Below ODE and animate the motion of pendulum according to the ODE solution   Objectives : 1. To write a program in Matlab to solve above ODE equation.                      2. To create an animation of the motion of pendulum.     …

AIM: Write a code in MATLAB to optimise the stalagmite function and find the global maxima of the function.   OBJECTIVES: 1.To expalin the concept of genetic algorithm and also explain the syntax for ga in MATLAB. 2.To Plot graphs for all 3 studies and for F maximum vs no. of iterations.  …

                                                                                           …

                                                                                           …

TOOLING  AXIS CREATION Selection for direction of tooling axis depends on ease at which components can be easily ejected. For fan cover surface point has been created using point command which is the center of the top hole. Axis system at this point has been created which has same directions as that of current axis…

TOOLING  AXIS  CREATION Selection for direction of tooling axis depends on ease at which components can be easily ejected. For Base Bracket surface point has been created using point command which is the center of the top hole. Axis system at this point has been created which has same directions as that of current…

 TOOLING  AXIS  CREATION Selection for direction of tooling axis depends on ease at which components can be easily ejected. Most down face of the switch bezel has extracted using extract command. For switch bezel surface point has been created using point command which is the center of the surface. Axis…

TOOLING  AXIS  CREATION We always make tooling axis with respect to Circle or Bin. In coin holder bin is present hence we take it as reference for creating tooling axis.We have extracted base of bin. For coin holder base  surface point has been created using point command which is the center of the surface.…

TOOLING  AXIS  CREATION Selection for direction of tooling axis depends on ease at which components can be easily ejected. Most down face of the switch bezel has extracted using extract command. For switch bezel surface point has been created using point command which is the center of the surface. Axis system at this point…

RIB  DESIGN Fully Defined Sketch Design Of Rib With Rules 1.Maximum Height of the rib should be 5 times the thickness of the plastic component.  As thickness of the plastic component is 2.5 mm hence maximum height = 2.5 x 5 = 12.5 mm 2.Rib thickness at the base should be 0.4 times the thickness of the plastic…

SCREW  BOSS  DESIGN 1.Thickness of the screw boss should be 0.6 times the thickness of the component Thickness of the component = 2.5 mm Screw Boss Thickness = 2.5 x 0.6 = 1.5 mm Hence Outside Diameter = Inside Diameter + 2 * Screw Boss thickness As Inside Diameter = 5.2 mm Outside Diameter = 5.2 + 2*1.5 = 8.2 mm 2.Height…

TOOLING  AXIS  CREATION Point has created on the class A Surface for creating tooling axis. Tooling axis has been created from point in a Y direction. DRAFT ANALYSIS OF CLASS A SURFACE Using insert command draft analysis tool has opened. By clicking on feature draft analysis two pallets opened. One pallet has necessary…

AIM - To design a B pillar of an automobile. OBJECTIVES - To create the main tooling axis and perform a draft analysis on the class A surface of the B pillar. To create class B and class C surfaces. To create dog house and locator using Master section. To perform a draft analysis on the final component. THEORY - Pillars…

AIM - To design Quick Release Mechanism and CV Joint. OBJECTIVES  To design the parts of quick return Mechanism and create a assembly of it. To create drawings of parts , assembly of quick return mechanism. To design the parts of CV Joint and create a assembly out of it. To create drawings of parts , assembly of …

AIM - To design Door Arm rest Using CATIA. OBJECTIVES  To create tooling axis following the OEM standard. To perform draft analysis on class A surface. To create class B surface. To create class C surface. To create close body. To perform draft analysis on close body. THEORY  Door arm rests has following applications.…

3D MODELING  , ASSEMBLY AND PHOTOREALISTIC RENDERING OF AN AMERICAN CHOPPER AIM - To Create 3D Model of an American Chopper OBJECTIVES  To 3D Model Parts of American Chopper To create Assembly of an American Chopper To create Photorealistic Rendering of an American Chopper  INTRODUCTION Solidworks - SolidWorks is a solid…

3D MODELING  , ASSEMBLY AND PHOTOREALISTIC RENDERING OF SUNSEEKER PREDATOR YACHT AIM - To Create 3D Model of an Sunseeker Predator Yacht OBJECTIVES  To 3D Model Parts of Sunseeker Predator Yacht To create Assembly of an Sunseeker Predator Yacht To create Photorealistic Rendering of an Sunseeker…

AIM - To design a Door Panel of an Automotive using CATIA V5. OBJECTIVES - To create an assembly and organize different surfaces of the given class A surface into different parts of the door trim panel. To create a tooling axis and perform a draft analysis on the class A surface of each part. To create class B, class…

QUESTION Benchmark with presently available cars in the market for the following case. Mr. D.S. Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His Family comprises five members including his wife, a five-year-old boy, his father, and his mother. He visits his native place Madurai…

UNDERBODY COATING Underbody coating is a dense cladding that is placed uniformly to the vehicle's underside. When the car is fresh out of the dealership and spotless, it is usually sprayed or painted on. It's fine, however, if you get the undercoating applied after a number of years. This is because it might protect the…

AIM - Design of Frontal BIW Enclosure of a car ( Hood or Bonnet ) OBJECTIVES -  Design of Hood Inner Panel by following given Master section with emboss creation Creation of Embosses on Hood Inner Panel for Hinges Assembly of Hinges with Inner Panel Creation of Latch Trajectory Mounting and assembly of Striker with…

AIM - Calculation and Optimization of section modulus for hood design OBJECTIVES -  To increase the strength of a hood THEORY -  Section modulus  Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members. The elastic section modulus is defined as S = I / y, where I is…

AIM - Design of front fender of a car OBJECTIVES   To create mounting for the Drip area To create mounting for A-pillar To create mounting for Sill   To create mountings for Bumper To create mountings for Baffles THEORY  Front Fender Fender is the American English term for the part of an automobile,…

AIM - Scrutinization of Wheel Arch area of given fender design as per European standards OBJECTIVES To find out clearances of the fender with respect to the wheel arch area as per European standards THEORY Wheel Arch The wheel arch is the semicircular part positioned above the wheel of a vehicle.  The wheel arch…

AIM - Design of an Automotive Roof  OBJECTIVES -  To design Front Roof Rail To design Rear Roof Rail To design Centre Roof Rail To design Bow Roofs To find Moment of Inertia of Bow Roofs To perform Draft analysis on all the Rails and Bow Roofs To check the Roof for Heat Distortion criteria To check the Roof for…

AIM - Design of an Automotive Backdoor OBJECTIVES -  To design Inner panel of a Backdoor To create a hinge and latch Trajectory To design Reinforcements for Hinge, Gas stay, Wiper motor, and latch Mounting  To design Outer Panel of a backdoor with hem To perform draft analysis on the Inner panel of a backdoor…

AIM  To create a Midsurface for the given Model To Mesh given component with the size of 5 Units To create RBE2, RBE3 links and 1D Elements on the following component with given cross-section and DOF at given locations GIVEN DATA a. Rod element:- Translational DOF should be Constrained with RBE2 link Cross-Section: BOX-…