Deriving 4th order approximation of a 2nd order derivative using Taylor Table method Aim: To derive the following 4th order approximations of the second-order derivative.  1. Central difference 2. Skewed right-sided difference 3. Skewed left-sided difference and write Matlab code for the above. Objective:  To…

                                       Solving the steady and unsteady 2D heat conduction problem Aim: To solve 2D heat convection problem for steady state and transient state analysis. Objective: 1. To solve Steady state…

            MacCormack's technique to solve conservation and non-conservation forms of the governing equations Aim: To solve conservation and non-conservation forms of the governing equations and using the MacCormack's technique. Objective: To find the following, 1. Steady-state distribution of primitive variables inside…

                                               Simulation of a backward facing step in OpenFOAM Aim: To simulate backward faing step in openfoam. Objective: 1. Simulate an incompressible-laminar-viscous flow through the backward facing step geometry and perform a transient simulation. 2. Perform 2 case studies as described…

                                              Finite Volume Method Literature Review Aim: To describe the Finite volume method (FVM) and its applictions. Objective:  1. Finite Volume Method(FVM), and the major differences between FDM & FVM. 2. Need for interpolation schemes and flux limiters in FVM.   Solution: Finite…

                                                   Simulation of Flow through a pipe in OpenFoam Aim: To simulate the axi symmetric flow in a pipe through openfoam. Objective:  Validate…

                 Validation studies of Symmetry BC vs Wedge BC in OpenFOAM vs Analytical H.P equation Aim: To simulate the flow in a pipe through openfoam. Objective:  Validate Hydro-dynamic length with the numerical result Validate the fully developed flow velocity profile…

                                              Surface meshing on a Pressure valve Aim: To cleanup topology and mesh for different target lengths. Objective:  Target length = 1mm, 3 mm and 5 mm (i.e.…

                                                CFD meshing on Turbocharger Aim: To mesh the turbocharger model with given criterias. Objective: Surface mesh target length for specific parts. Blade…

                                                            BMW Car Meshing using ANSA Aim: To mesh BMW Car for different target lengths. Objective: Target lengths…

                                                                   SURFACE WRAP Aim: To surface wrap the automative assembly.   Objective: Geometry…

                                                                                Flow over a Cylinder Aim: To calculate…

                                                               External flow simulation over an Ahmed body Aim: To run external flow simulation over Ahmed body. Objective:  Run the simulation for the velocity of 25 m/sec with the default air properties in fluent.   Theory: Ahmed body is a simplified car model, the flow…

                                                                MIXING TEE Aim: To set up steady-state simulations to compare the mixing effectiveness when…

                                                                              CHT Analysis on Exhaust port Aim: To run simulation…

                                                                                Rayleigh Taylor Instability Aim: To…

                                                                      CHT Analysis on a Graphics card Aim: To perform a steady-state conjugate…

                                                                TESLA CYBER TRUCK CFD MESHING Aim: To perform meshing of Tesla cyber truck. Objective: Mesh…

                                                                TESLA CYBER TRUCK CFD MESHING Aim: To perform meshing of Tesla cyber truck. Objective: Mesh with target length of 3 mm. Procedure: Geometry clean-up: Open the geometry in ANSA. Check for Triple cons and single cons. Delete the unnecessary faces and create…

                                                                  Simulating Cyclone separator with Discrete Phase Modelling Aim : To perform analysis on cyclone separator and calculate the separation efficiency and pressure drop. Objective:- To write a few words about any four empirical models used to calculate the cyclone…

                                                                        Parametric study on Gate valve Aim: To perform gate valve simulation…

                                                                   Simulating Combustion of Natural Gas Aim: To perform combustion simulation of natural…

                                                                   Converging diverging nozzle Aim: To study CD nozzle using Ansys Fluent. Objective:…

                                                                                           Pitot Tube Aim: To study on pitot static tube. Objecive:  1. A literature review of pitot-static tube. Also establish a relationship between Total (stagnation) pressure and static pressure 2. To create surfaces and fill it separately…

                                                             Turbulence modelling challenge Aim: To explain turbulence modelling and run simulation for Golf ball. Objective: …

                                                                   Moving zones approach in Fluent Aim: To simulate rotary motion using moving mesh. Objective: …

                                                        Flow Analysis over an airfoil at subsonic and supersonic regime Aim: To setup the domain for analysis of flow over an airfoil at subsonic and supersonic regime. Objective: Airfoil will be analysed at 3 different angles of attack and the lift and drag coefficient will…

                                                             Unsteady moving zones Approach Aim: To simulate flow using unsteady approach in turbomachinery. Objetive:…

                                                            Broadband Noise modelling over Ahmed body Aim: To run simulation for Ahmed body with acoustic field. Objective:  Describe Ahmed's body and its importance. Setup the domain and setup assuming body is travelling at 110 kmph Run the setup till convergence and plot…

                                                                 Exploring the GUI of GT-POWER Aim : To give a brief idea about GT Power. Objective: Explore…

                                                             Calibration of Single cylinder SI-Engine Aim: To run analysis for SI engine. Objective: 1.Run the case at 1800 rpm and list down important parameters air flow rate BMEP BSFC In-cylinder pressure 2. Increase the power output at 3600 rpm by 10%   Theory: A spark-ignition…