Report Here firt we discuss how we created a tooling axis. First we extracted the base of the switch bezel and make a center point for that base, axis is added for the base at the center point. After creation of axis we create a position sketch at xy plain to of the axis  in the sketch we draw two lines…

Aim:- The Aim of the project is to create a solid model of the given class A surface of the Door Arm Rest by applying the design rules. Objective:-  To create a tooling axis on the class A surface so that we can perform the draft analysis on class A surface and the solid part. To create the class B and class C surface…

Aim:- The Aim of the project is to create a solid model of the given class A surface of the Coin Holder  by applying the design rules. Objective:-  To create a tooling axis on the class A surface so that we can perform the draft analysis on class A surface and the solid part. To create the class B and…

Aim:- The Aim of the project is to create a core and cavity block of switch bezel. Objective:-  To create a tooling axis on the class A surface so that we can perform the draft analysis on class A surface and the solid part. To get the final solid closed body for Core and cavity blocks. we need to plublish…

Aim:- The Aim of the project is to create the rib for the Centre console coin holder considering the design rules. Tooling Axis:-  Here first we will discuss how the tooling axis is created for the give class A surface. In the given class A surface the side walls are perpendicular to the base so it will…

Aim:- The Aim of the project is to create the screw boss and Dog House for the Centre console coin holder considering the design rules. Design rule to create screw boss:-   Draft  - 0.5 degrees on walls of boss.   Thickness -  Typically 40%* of the nominal wall at the base.   Height…

Aim:- The Aim of the project is to create a solid model of the given class A surface of the Door Applique and create the Heat Stakes and the locators considering the design rules. Given Door Applique class A surface. Tooling Axis:-  Here first we will discuss how the tooling axis is created for the give…

Aim:- The Aim of the project is to create a solid model of the given class A surface of the B pillar by applying the design rules. Objective:-  To create a tooling axis on the class A surface so that we can perform the draft analysis on class A surface and the solid part. To create the class B and class…

Aim :- To create part model,2d drafting and assembly of quick return mechanism and cv joint. Quick Return Mechanism :- Slotted lever First we drawn the sketch of slotted lever. Next we pad the sketch. Swinging Arm The same method we did for slotted lever we do for other parts also Base circle and pin Rectangular slider…

Aim:- The Aim of the project is to develop car door trim using Catia V5 with given class A surface and also create B side features using the design rules. Objective:-  To create a tooling axis on the class A surface so that we can perform the draft analysis on class A surface and the solid part. To create…

                                                                     American chopper Objective : The objective of the project is to model the different…

 1. Radar Mast  Isometric view Front view side view Feature tree  2. Yacht Assembly  Objective : The objective of the project is to model the different parts of the Yacht using solid works. To assembly the different parts of the Yacht. To create the photorealistic rendering for the assembled chopper…

                                            DESIGN OF SHEET METAL CASING USING NX CAD Objective : The objective is to design a sheet metal casing using NX CAD Introduction :   Sheet metal is metal formed…

                                            DESIGN OF SHEET METAL BOX ASSEMBLY USING NX CAD Objective : The objective is to design a sheet metal Box Assembly using NX CAD Introduction : Sheet…

                                            DESIGN OF SHEET METAL ENCLOSER USING NX CAD Objective : The objective is to design a sheet metal Encloser using NX CAD Introduction : Sheet metal…

                                            DESIGN OF SHEET METAL BRACKET USING NX CAD Objective : The objective is to design a sheet metal Bracket using NX CAD Introduction : Sheet metal is metal…

                                       DESIGN OF SHEET METAL BRACKET-ll USING NX CAD Objective : The objective is to design a sheet metal Bracket-ll using NX CAD Introduction : Sheet metal is metal formed…

Benchmarking Benchmarking is a process of measuring the performance of a company’s products, services, or processes against those of another business considered to be the best in the industry, aka “best in class.” The point of benchmarking is to identify internal opportunities for improvement. By studying…

Underbody Coating : Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the undercoating applied after a couple of years,…

Aim :  To Design and Assemble the Hood outer panel, Inner panel and the necessary reinforcements by following the Master section. Introduction : The hood or bonnet is the hinged cover over the engine of car. Hoods can open to allow access to the engine compartment, or trunk on rear-engine and some…

Aim : The aim of the project is to Calculate the section modulus of the designed hood and to Come up with the new section that has improved section modulus by optimising the previously designed hood. Introduction : Section modulus is a geometric property for a given cross-section used in the design of beams or flexural…

Aim :- The aim of the project is to calculate the wheel arc and prove whether the car will pass the standards or Not according to Europian Standards. Sketch is drawn by considering the European standards as follows :- Sketch is drawn by considering wheel centre as origin point. Horizontal line is drawn from the…

Aim : To design the Front Fender using NX CAD. Objective : Design the Fender with the necessary Mounting areas given below:1. Drip area2. A-Pillar mount3. Sill mount4. Bumper mount5. Baffle and splash mount Introduction : Fender is the part of an automobile or other vehicle body that frames a wheel…

Aim :  To Design and Assemble the Roof and the necessary reinforcements by following the Master section. Introduction : An automobile roof or car top is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and other…

Aim :  To Design and Assemble the Back Door outer panel, Inner panel and the necessary reinforcements. Introduction : Tailgate is the closing door of the luggage compartment.It provides the aesthetic outer appearance to the vehicle as well as wind flow aerodynamic surface.Tailgate is a single stamped or…

Aim : The aim of the project is to convert the mechanical part to the electrical connector using the electrical part workbench by applying the electrical properties. Procedure : Create/Download 3D connector Create required geometrical parameters In the reference geometry required reference points like bundling entry point…

Aim : The aim of the project is to create the electrial harness layout in Electrical workbench using the following connections as shown in the layout. DT06-08SA DT06-6S DT06-4S DT06-2S Procedure : Create/Download 3D connector Create required geometrical parameters In the reference geometry required reference…

Aim : The aim of the project is to Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Procedure : procedure for connector creation Create/Download 3D connector Create required geometrical parameters In the reference geometry required reference points like bundling entry point connector…