AIM: Create the Base Bracket Plastic component through the given Class-A surface.For that to begin with i went on to check and ensure the connectivity of CLASS A  surface By using join command we can ensure whether the parts of surface A is joined and where are it's boundaries also.So here in our case there is…

AIM: To create a switch bezel model using the given CLASS A  surface. STEP 1:Ensure the connectivity of the given CLASS A surface by using the join command The given CLASS A surface is made a single part using the join command and now we must create a tooling direction to meet the requirments of draft analysis STEP…

AIM: Create the Coin Holder Plastic component through the given Class-A surface.To begin with we check the connectivity of the given CLASS A surface STEP 1:Ensure the connectivity of the given CLASS A model using join command.here every given surface is selected and joined using join command STEP 2:Tooling axis creation…

 MODEL DRAWING 1:QUICK RETURN MECHANISM FIVE DIFFERENT parts to make the assembly of quick return mechanism is made using part body by creating sketches for each and then adding and removing using boolean is also done inside each part bodies different parts made are given below: then using assembly workbench these five…

ATTACHMENT FEATURE CREATION:RIBS AND SCREWBOSS AIM:To create b-side attachment featues like ribs and screwboss by creating a model from given class-A surface.our first requirement is to create a model using A-B conversion STEP 1:CLASS A SURFACE connectivity check-Input surface is given CLASS-A surface and we perform a…

ATTACHMENT FEATURE CREATION-DOG HOUSE AIM:To create a B side attachment called dog house on the given part by creating the part using A-B conversion from given A surface. STEP 1:CONNECTIVITY CHECK ON GIVEN A SURFACE The given A surface is checked for the connectivity and joined using join command and the sharp edges that…

AIM:TO CREATE B SIDE ATTACHMENTS LIKE HEAT STAKES AND FOUR WAY LOCATORS STEP 1:CHECK THE CONNECTIVITY OF CLASS A SURFACE To begin with we ensure the connectivity of CLASS A surface uisng join command and check for whether there is any sharp edges  are there on the surface that needs to be removed.For this surface there…

AIM:TO CREATE BUMPER PLASTIC PART THROUGH GIVEN CLASS A COMPONENT STEP 1:ENSURE CONNECTIVITY OF GIVEN CLASS A SURFACE The given CLASS A surface is checked for its connectivity using join command and the CLASS A surface is repaired for any sharp edges present using tools like multi-section and blend tools STEP 2:TOOLING…

AIM:TO DESIGN A PILLAR WITH GIVEN MASTER SECTION AND ATTACH B SIDE FEATURE (DOG HOUSE) STEP 1:TO CHECK THE CONNECTIVITY OF GIVEN CLASS A SURFACE The given CLASS A surface is checked for connectivity using join tool and after joining repair is carried out on the sharp edges that are present in the CLASS A surface and an…

FINAL PROJECT:DEVELOPMENT OF A DOOR TRIM PANEL INPUT SURFACES: -CLASS A surfaces of the DOOR ARM REST, MAP POCKET, BOTTLE HOLDER and LOWER SUBSTRATE. -MASTER SECTION FOR ATTACHMENT CREATION -PUSH PIN CLIPS TO ATTACH ON DOG HOUSE FOR FITMENT PURPOSE   DOOR TRIM PANEL OF AN AUTOMOBILE: The door trims are the interior parts…

HOOD DESIGN AIM:Design Hood Outer Panel, Inner Panel and the necessary reinforcements by following the Master Section mentioned with the Design parameters. OBJECTIVE:  It is required to create a hood assembly including hood outer panel,hood inner panel along with necessary reinforcements.Also master section is…

FENDER DESIGN-WHEEL ARC CHALLENGE AIM:To calculate the Wheel Arch gap at required points and check whether the car passes the European standard or not. FENDER Fender is the side closing component for the engine compartment. It's major role is to avoid chipping sand, small stones and mud particles inside…

Section Modulus calculation and optimization AIM:To calculate the section modulus for two iterations and to find out which one will be the best one to be considered. SECTION MODULUS Sectional Modulus (Z): It is the ratio of moment of inertia (I) of the beam cross-section about the neutral axis to the distance (ymax)…

FENDER DESIGN AIM:To create a fender side part and its mountings as per the given master section and also according to the requirements using the given styling surface FENDER Fender is the American English term for the part of an automobile, motorcycle or other vehicle body that frames a wheel well (the fender…

UNDERBODY COATING Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile.It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the undercoating applied after a couple of years, it’s…

ROOF DESIGN AIM:To create a ROOF ASSEMBLY from the given styling surface and to provide necessary support rails such as FRONT ROOF RAILS,BOW ROOF RAIL1,CENTRE ROOF WITH REINFORCEMENT,BOW ROOF RAIL2 & REAR ROOF RAIL  and also to carry out HEAT DISTORTION CALCULATION AND SNOW LOAD PREDICTION  calculation.Considering…

BENCHMARKING It is the process of comparison of a particular product to another,to differentiate and analyse the current flaws and goods and hence to improve by gaining insights.. Benchmarking can measure the quality and effectiveness of policies, programs, services, products and processes within an organization and help…

DESIGN OF BACKDOOR AIM To create a backdoor assembly from  given CLASS A  surfac,also to provide necessary reinforcement and to carry out draft analysis BACKDOOR Backdoor of a car is the opening in the rear end of the car that provides access to either boot space or passenger compartment depending the design …

ASSEMBLY Assebmly is done by fixing the butterfly valve body and inserting the shaft and arresting the 5 DOF s of the shaft by leaving a rotation of it for the proper functionality.Then we will insert the plate on the shaft and areest all the DOFs of plate with respect to shaft.Retainer will be placed on the flat face…

Deutsch DT06 – 08SA We need to specify the part using define connector in the electrical part design workbench and need to specify number of terminals, which is for this connector is 8 Now we need to specify connector connecting point and bundle connecting point using Define connector connection point and bundle…