clear all close all clc % A programme to simulate the motion of a pendulum using 2nd order ode. % inputs b = 0.05; %..........damping coefficient g = 9.81; %..........gravitational acceleration(m/s^2) l = 1; %..........length of string(metre) m = 1; %..........mass of bob(kg) % initial conditions for angular displacement…

clear all close all clc % A project report on parsing NASA's thermodyanamic data f3 = fopen('THERMO.dat','r'); %.......the command "fopen()" is used to open the file % by typing file name in inverted comma % in parenthesis after fopen, 'r' stands % for permission for read the file % content. this result is stored in %…

A report on defining components and creating catalogue 1) Giving geometrical parameters: after downloading the component from the link & unzipping it, the component is opened into the catia  to open the component in software, the steps are: file > open > select the downloaded unzipped file > press enter.…

A challenge complition report on P Clamp, backshell,corrugated tubes, catalogue of corrugated tubes. 1) Defining P clamp after downloading .igs p clamp file open it into catia's part design workbench. in order to give the geometrical parameters click on point option available on reference element toolbar>a window will…

 A report on routing a harness layout in electrical workbench 1) Defining all the connectors electrically and storing it in a catalogue document download all the given connectors from te.com and unzip it. open any of the connector mentioned in the given layout in catia's part design workbench give the geometrical…

A report on week 5 & 6 challenge. 1) defining all the connectors electrically and storing them in the catalogue. after downloading all the connectors and extracting it, open one of the connector in catia's part design workbench. give the necessary geometrical parameters (points,axis) on its connector connection side and…

A report on week 7 challenge 1) Electrical definations & bundle flattening It is necessary to define all the connectors electrically. for that all the connectors should be define as a connector and also their connector connection & bundle connection points must be defined in electrical part design workbench. …

A REPORT ON PROJCT 11) defining all the cat parts a) defining the connectors & catalogue creation:open any of the connector from project 1 data in part design w/b > identify the bundle connection and connector connection sides > give the geometrical parameters (points and axis) on the bundle connection(point…

  A REPORT ON PROJCT 2 1) defining all the cat parts  a) defining the connectors & catalogue creation: open any of the connector from project 1 data in part design w/b > identify the bundle connection and connector connection sides > give the geometrical parameters (points and axis) on the bundle connection(point…

 A report on benchmarking   What is benchmarking?         Benchmarking is a quality by comparision for achieving better standards.         In the global movement today, the competition is increasing at faster rate. Hence the only way to         …

A report on hood design Hood: hood is an essential part of an automobile vehicle which covers and protects the engine as well as other important components which assembled with the engine inside the engine bay.  It also act as a door with locking mechanism which opens and closes in order to access the engine bay for…

A report on SECTION MODULUS Section Modulus: Section Modulus is a geometric property used to calculate the bending stresses in a structural member. Mathematically section modulus is define as the ratio of total moment resisted by the section to the stresses induced in the extreme fibre. It gives information about how much…

A Report On Wheel Arch Design Objective: To inspect the given fender design to verify whether the wheel arch of the fender meets the European Standards or not. Introduction: The wheel arch area is one of the important part in fender design because it deals with some of the safety regulations for pedestrians, for the vehicle…

A Report On Front Fender Design   Objective: To design a front fender of an automobile vehicle from the given skin data and create different types of mountings                     on it. Fender: Fender is one of the important outer body part of an automobile vehicle whose function is to cover or shield the wheel above…

 A report on 'Roof Design' of a passenger car   Objective :  To design and model Front roof rail, Rear roof rail, Centre roof rail, Bow roofs and their assembly for the given skin part of the roof using NX12. Roof curvature study for :         1) Heat destortion criteria    …

A Report On 'Underbody Coating' Of An Automobile Vehicle   Objective: To understand the purpose of Underbody Coating for the Automobile Vehicle's body, types of underbody coating and it's pros and cons.   Underbody Coating: Underseal or undercoating is a thick resilient coating applied to the underbody or chassis…

A Report On Backdoor(Tailgate) Design Of The Passenger Car   Objective:  To design and model the Inner Panel of the backdoor with the Reinforcements and embosses for Hinges, Latch, Gas-Stay and Wiper Motor from the given styling surface using NX12. Perform draft analysis on the inner panel and create an assembly of outer…

A report on week 7 challenge Assembly Workbench: Steps followed to prepare an assembly: 1) Part Creation: Each part of the assembly is been created in the part design workbench by drawing the sketches with all the constrains and by using 3d modeling commands like pad, pocket and other methods like boolean operations a…

A report on base bracket design draft analysis The draft analysis determines whether the part is manufacturable or not. The forming processec which uses the core and cavity to manufacture the parts always required some draft. Draft allows the formed part inside mold to get eject from the core and cavity. It helps the part…

A Report On Switch Bezel Design   Draft Analysis: The draft analysis determines whether the part is manufacturable or not. The forming processec which uses the core and cavity to manufacture the parts always required some draft. Draft allows the formed part inside mold to get eject from the core and cavity. It helps…

 A Report On Bumper Design Objective : To design class B surface and class C surface for the given class A surface of the bumper and make a solid part                       using 'close surface' method.   Draft Analysis: The draft analysis determines…

A Report On Attachment Feature Creation (Ribs & Screw Boss)   Objective:1) Create the rib for the Drill Handle considering the design rules.                  2) Create the Screw boss for the Drill Handle considering the design rules.   Draft Analysis: The…

                                              A Report On Attachment Feature Creation (Dog House)   Objective:  To create class B and class C surface for the door trim lower skin part and…

                          A report on Door Trim Lower with Engineering Features (Heat Stakes & Locators)   Obective: To create class B and class C surface for the door trim lower skin part and creat heat stakes and locators on the b …

A Design Report On Assembly Of The Butterfly Valve Exploded view of all the parts include in an assembly All the parts are assembled together by using the constrains like touch, align, concentric etc. Assembly of the vlave and its different orientation views.         2D Drafting Of The Assembly And Application Of GD&T

 A Report On 'A pillar Plastic Trim (A Pillar Cover) Design' Objective:  1. To create class B & C surface for the given A-surface of A-pillar cover and make these three as closed surfaces to get a solid part using close surface method in CATIA.   2. To design the doghouse using the master section provided with class A…

A Design Report On 'Door Trim Panel Assembly' Objective: To design solid bodies of door trim panels from given class-A surface, design and develope B-surface engineering features like heat stakes, locators, doghouse, ribs, attachement flanges using given master-section. Perform draft analysis on each panel.   Introduction:…

A Report On Casing Design Objective: To design a sheet metal casing using NX sheet metal application as per given guidelines.   Intorduction:  The NX sheet metal application is a powerful tool to design and develop the numerous sheet metal components in different sectors. It has been used in wide range of industrial sectors…

Design Report On Box Assembly   Objective: To design a sheet metal box using NX sheet metal application as per the guidelines.   Design Methodology: Recommended workflow to create simple sheet metal part:   Features and commands used to generate the design: 1) Tab tab is the command which is used to create the base feature…

Designing Of Odd Shape Enclosure   Objective: To design an enclosure for odd shape part using NX sheet metal application.   Intorduction:  The NX sheet metal application is a powerful tool to design and develop the numerous sheet metal components in different sectors. It has been used in wide range of industrial sectors…

Bracket Design   Objective: To design a simple sheet metal bracket using NX sheet metal application.   Intorduction:  The NX sheet metal application is a powerful tool to design and develop the numerous sheet metal components in different sectors. It has been used in wide range of industrial sectors such as mechanical,…

A Report On Metal Bracket Design   Objective: To design a sheet metal bracket using NX sheet metal application.   Intorduction:  The NX sheet metal application is a powerful tool to design and develop the numerous sheet metal components in different sectors. It has been used in wide range of industrial…