Aim:-To Calculate the Concrete Mix Design for M35 grade concrete with fly ash. Introduction: Design mix iprocess is used to design by structrual engineer.It is use to gain accuracy of required strength and hardness from available ingrediants of concrete It used to gain required strength and hardness. it can be controlled…

 Aim & Introduction: To sketch G+1 building and calculating the loads acting on  building. Procedure: Calculation of load acting on building: Assumed dimensions of buliding  All columns are 300mm x 300mm All beams are 300mm x 450mm Slab thickness if 125mm The height of the wall is 4.5m Dead load calculation:…

  AIM: To Create the geometries from P1 to P2 using all the coordinates system methods. by using the Line tool and circle  tool to create the geometries in Imperial Template and the Decimal Units to draft the features with refrence dimensions. Procedures :    AIM: To Create the geometries…

AIM AND INTRODUCTION : CREATING A CROSS SECTION WALL USING AUTO CAD AS PER REFRENCE DRAWING. PROCEDURE:   OPEN NEW FILE  SELECT UNITS  TYPE RECTANGLE LINE  IN COMMAND BOX SPECIFY FIRST POINT 0,0 SELECT DIMENSION AND PROVIDE DIMENSIONS LENGTH AND WIDTH 1.5 AND 0.15 ENTER  TYPE RECTANGLE LINE …

Creating a drawing using Auto CAD as per refrance manual drawing in attachment  .   Aim and Introduction: To Sketch the layout of a residence as shown in the Figure 1. Consider all dimensions as reference to sketch the unit plan and Also the text in the layout are only for reference. the missing dimensions are assumed…

      AIM & INTRODUCTION:  To create a column schedule as shown in the figure by using auto cad .  Procedure: Get in to a new drawing file and set start up settings in to Imprerical  Set limits as 10',10' by using LI command  Set the text height as 8" and text style as Romans.SHX …

AIM & INTRODUCTION : To draw the elevation and details of a wardrobe by using auto cad as shown in the Figure below.along dimensions and text with the use of layers.  Note: All dimensions are in mm. Start with New drawing  file Set the units in millimetre Set dimensions size 50mm text size as 50mm PROCEDURE…

 AIM & INTRODUCTION :  To create the Plan and Sections as shown in the Figures. by using  proper dimension techniques and dimension styles to document the project. the sizes of the doors and windows are assumed  as per construction standards. The stair details are refered from section. PROCEDURE:…

Aim & Introduction : To draw a Architectural drawing of area size of 60’x20’(18.3m x6m) with facing east side. Procedure : Coomand used: Line Xline Polyline Rectangle Circle Arc Trim Move Offset Hatch Layer MatchProperties Multileader Fillet Copy Explode Dimlinear Dimcontinue Dim break Dim…

AIM & INTRODUCTION: To draw a templates as shown in Figures. Take the size of the title block as per industry standards or you can assume  Use text and attributes wherever required and create  the title block you need to save it as a block with names: Custom1_titleblock and Custom2_titleblock, respectively.…

Aim& Introdiction : To draw the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks whereverrequired and provide appropriate dimensions in the plan. Procedure: Open new drawing file  Set units in millimetre 1.Creating a below counter plan: Draw a rectangle of 4300 mm,3200mm by using Rectangle command …

Aim & Introduction: To create a 3D Furniture element as shown in the Figure. Procedure: Command used: Line join Trim Offset 3D Orbit Extrude Union Draw rectangle of 3’ x 3’ Offset the rectangle of thickness 2” Explode the rectangle Make it region Region > select the inner area > enter Extrude…

Aim & Introduction: To create a 3D Isometric View of the building with given plan and elevation. Commands used: Rectangle Line Explode Extend View 3D orbit Boundary Extrude Union Subtract Align Procedure: Open new drawing file Change the setting in to 3d modelling Change unit to engineering Change the dimension settings…

Aim & Introduction: To create layout and plot the plan and section of the project challenge 7 by using template of mArch.dwt in auto cad by using MV command to create the viewport of the size asshown in Figure and also, use ATTEDIT command to edit the information in the title block. the size for the layout…

AIM & INTRODUCTION: To creating a 3D rendered model for a Residential Building in AutoCad PROCEDURE: 1)TO CREATE PLAN AND SECTION: COMMANDS USED : Layer Line PL XL Offset Rectangle Tool pallet Array Mirror Copy Trim Extend Dimension linear Hatch 1.Create a layer as per requirement Layer > new layer > specify…

1.From the file menu, create a new project (Structural / Architectural / Construction template) and name the project appropriately Aim: To create a template of Structural / Architectural / Construction and name the project appropriately Procedure: 1.Creating a structural template Click the window icon Type Revit in search…

  1) What is BIM? Summarize the features of BIM and benefits of using BIM over 2D CAD tools.BIM is a process for creating and managing information on a construction project throughout its whole life cycle. Ans: BIM stands for Building Information Modeling. It is  process, a coordinated digital description…

1) Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with grids created from…

    1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level. AIM & PROCEDURE: To create ceiling for week 3 model using architectural tab in Revit. Procedure: Open week 3 revit file Goto to architectural…

1) Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project Aim: Procedure: open revit file  select new ARCHETECTURAL TEMPLATE create horizontal and vertical grids   GOT TO MANAGE> COORDINATES > specify coordinates   select the grid…

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School Ans:  I choose office building among the top 3  2) Assume reasonable assumptions for…

1) What are HVAC systems? Why are they essential in the modeling of buildings   The full form of HVAC is Heating, Ventilation, and Air Conditioning. HVAC systems generally control temperature, humidity, and quality of air in a building or any occupied space. The main goal of the HVAC system…

1) Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below           a. Using 3D model create a section box           b. To create similar doors and windows in a floor plan layout         …

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. Procedure: Open Revit software  goto manage tab > select  dynamo option Select New  Type code block and sliders  in search option Create a required element in the library    goto…

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class. Procedure: Open revit files of architectural file  goto file > export > naviswork nwc  Specify the…

Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental period of vibration (T1 = 2 seconds) and…

1. Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. Objective : To under stand the vertical and horizontal Impact in seismic behaviour…