PROJECT 1.AIM:- To find the mix design for M50 grade of concrete without fly ash.   PROCEDURE:-   Step 1:- Stipulations for proportioning  Grade designation : M50 Tyoe of cement : OPC 43 grade conforming to IS 8112 Maximum nominal size of aggragate…

1.                                                                 G+1 BUIDLING  AIM:- Sketch a G+1 floor residential plan, according to Vaastu Shastra,…

  Drawing P1 Aim:- Create the geometries from P1  using all the coordinates system methods. Procedure:-  1. Using absolute coordinate system Steps Open autocad software. open new drawing sheet using short key cntrl N or from the application tab. Assign the units . Using the commands draw the figure…

Drawing C1 :- Cross section of load bearing walls over spred footing 1.AIM:- To draw cross section of load bearing walls over spred footing 2.INTRODUCTION:- The cross section of load bearing wall over spread footing using AutoCAD is created by Lines and Rectangles.  3.PROCEDURE:  STEP 1: Open the…

DRAWING 1 - DECIMAL AIM :- Drafting the given geometrical figure using Chamfer or fillet or obeject snap options etc. INTRODUCTION :-  PROCEDURE :- STEP 1. Open the AutoCAD software and click on new for a new drawing sheet.  Enter UNITS in command box.  Select DECIMAL in TYPE, 0.00 in PRECISION and METERS in UNITS TO SCALE…

DRAWING 1 - RESIDENTIAL PLAN Aim: To sketch the layout of a residence as shown in the figure above in AutoCAD. Introduction: The desired plan is created in AutoCAD using primarily the Construction line tool. The procedure of drawing is explained in detailwith diagrams of each step and the final result is given. Procedure:…

1. COLUMN SCHEDULE PREPARATION Aim: To create a column schedule with the help of lines as shown in the figure above in AutoCAD. Introduction:- The desired column schedule is created in AutoCAD using primarily the Line and Text tool. The procedure of drawing is explained in detail with diagrams of each step and the final…

1. WARDROBE DETAILED DRAWING Aim: To draw the elevation and details of a wardrobe as shown in the figure above, in AutoCAD. Introduction: The Wardrobe detailed drawing is created in AutoCAD using primarily the Line tool and after sketching. the dimensions and text are provided with the use of layers. The procedure of drawing…

 1.SECTION Aim: TO draw the plan as shown in the figure above, in AutoCAD. Introduction: The plan is created in AutoCAD using primarily the XLine and Line tools. the dimensions and text are provided With the use Of layers. The procedure Of drawing is explained in detail With diagrams Of each Step and the final result…

PROJECT 1.Design and Draft a layout of a residential building with the following details   a. Plot Size: 60’x20’(18.3m x6m)  b. Orientation- Facing East    c. Develop the following: 1. Architectural Drawing (Floor Plan, Elevations, and Sections) 2. Structural Drawing (Column, Bean, Footing Plan)   1.EAST FACING RESIDENTIAL…

  1.TEMPLATE USING TEXT AND ATTRIBUTES AIM: To create the template contains text and attributes using AutoCAD. INTRODUCTION: The template contains text and attributes using AutoCAD is created by Lines. The procedure and result should be written after creating the template using text and attributes. STEP 1: Open the…

1.Create the layouts of the Kitchen and provide hatches pattern. Aim: Create the layouts of the Kitchen and provide hatches pattern using lines, rectangle,hatch,blocks etc. Size of Doors and Windows are as followed : Door 1 or Dl as 1000mm X 2100mm Door 2 or D2 as 1000mm X 2100mm Window 1 or WI as 900mm X 1500mm  Procedure:…

1.Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use ATTEDIT command to edit the information in the title block. Use A1 size for the layout,Take…

 1. Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing. AIM :- To create a 3D Furniture element as shown in the question Figure using AutoCAD. INTRODUCTION: 3D Wireframe Model :- A wireframe model is a skeletal description of a 3D object. There are no surfaces in a wireframe model…

1.Create a 3D Isometric View of the building with plan and elevation given. AIM :- To create a 3D Isometric View of the building with plan and elevation as shown in question Figure using AutoCAD. INTRODUCTION :- 3D Wireframe Model :- A wireframe model is a skeletal description of a 3D object. There are no surfaces in a…

PROJECT 1:Create a 3 dimensional model of the residential building with a rendered view. AIM:- To create a Three-Dimensional model of the residential building with a rendered view using AutoCAD. INTRODUCTION:- 2D Wireframe Model :- A wireframe model is a skeletal description of a 3D object. There are no surfaces in a wireframe…

 1:- From the file menu, create a new project (Structural / Architectural / Construction template ) and name the project appropriately. AIM :- To create a new project Structural/Architectural/Construction template and name the project appropriately. INTRODUCTION:- Revit is BIM(Building Information Modeling) software…

1.What is BIM? Summarize the features of BIM and benefits of using BIM over 2D CAD tools. Aim:- To study what is BIM and its benefits over 2D CAD tools BIM To know What is BIM and to Summarize the features of BIM and benefits of using BIM over 2D CAD toolsBIM is an acronym for Building Information Modeling or Building…

 1) Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with grids created from…

 1.Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level. AIM:-Provide ceiling over the first floor level.Procedure :- STEP 1: Double click on the Revit application icon and opens the app. Click on "Open" in the…

 1.Why are building codes or standards essential for the modeling/efficiency of drawings in Revit ? Answer :- The National Building Code (NBC) is a standardised set of rules to be followed by authorities and construction firms, to provide a healthy and safe living experience for all residents. The NBC of India, a…

1. Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project Aim:- To set project base point and project shared coordinates for the project. PROCEDURE :- STEP 1 Click on windows start In Search bar type > Revit Click > Revit 2019 Once the revit is open, It…

1.Select the type of structure you want to build from one of the three below:a. Multi-Unit Residential Apartmentb. Office Buildingsc. School Answer :- I have selected school building.   2) Assume reasonable assumptions for geographic and location details for your project modeling. Based on assumptions and type of structure…

 1. What are HVAC systems? Why are they essential in the modeling of buildings HVAC refers to heating, ventilation and air conditioning which is used to move air between indoor and outdoor areas along with heating andcooling in the buildings. It regulates both air quality and temperature in the building. HVAC system goes…

 1. Use the shortcut keys in Revit discussed in class to complete the following tasks and list them belowa. using 3D model create a section boxb. To create similar doors and windows in a floor plan layoutc. To reduce the thickness of lines visible in plan viewsd. To apply override settings to a floor in the model…

1.Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. Answer :- Aim:- To use the Dynamo, create a set of sinusoidal points and create a curve as well as create a surface out of the curve. Procedure :- Step 1:- Click on windows start In Search bar type > Revit…

1.Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class. AIM : To export revit architectural model and structural model to "Navisworks". INTRODUCTION :-Navisworks project software…

1.What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate. AIM:-To find the type of structural issues and it's possible rectifications on the  following figures of  building structures. Damages on a structure:- A damage can occur in a structural frame…

1.Compute lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The system has 3 DOFs as shown. Assume L = 2h and Elb = Elc . Answers:- AIM:-Compute lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The system has 3 DOFs as shown. Assume…

Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental period of vibration (T1 = 2 seconds) and…

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. Answer:- Aim:- Analyse the given plan based on siesmic irregularities.…

Question 1: The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account…

Challenge 6 – ETABS modelling of a 25 storey building Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. Structural Element Sizes …

                                                    Comparative study of different storey buildings for Seismic forces Aim:- To model and analysis of bulinding from A to K as per the datas given…

Challenge 8 The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span continuous beam along grid A        2) 7 span continuous beam along grid 3 Address the following…

                                                              Reinforcement detailing of Columns from ETABS output   AIM:- Run the analysis and design the RCC Moment…

Challenge 10 Q.The etabs file for a G+6 building is provided. Run the analysis and design the RCC shear walls (show in the etabs model). The following challenge deals specifically with the shear wall of size 300x1500 at grid A-11 in the structural model. Extract values of longitudinal steel ratio, boundary element length…

Structural Modelling using Etabs 2018 AIM:- Conceptualize a framing plan layout and then model a G+7 residential building in zone 5 using Etabs software. The structural model must comply with provisions of IS 1893 and IS 13920 Finally  Run a modal response spectrum analysis and check analysis results of the etabs…

Design of Shallow Foundation (Isolated Footings) AIM:- To design a square footing for a column size of 400x400.  Also consider the following conditions such as; The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 metres below E.G.L. (Tapered…