1) Breakers Distributor Generator Motor Battery Current and Voltage regulator Foot selector switch Ammeter Fuel guage Ignition switch Ignition coil  Starter Fuse.   2) Breakers;  The breakers action needed when electric current flows along an undesired path with no or less load. If there is no breaker in…

1) Answer MATLABCODE CODE % excel file of voltage current data is to be uploaded. % read the excel file in the matlab program. A=xlsread("VI.xlsx"); A A = -17.3000 -28.0000 -17.1000 -24.0000 -17.0000 -19.0000 -16.8000 -14.0000 -16.5000 -9.0000 -16.0000 -6.0000 -15.0000 -4.0000 -14.0000 -3.0000 -12.0000 -2.0000 -10.0000…

1) PROBLEM STATEMENT: DESIGN A SIMULINK MODEL FOR DC MOTOR SYSTEM AND IMPLEMENT  PROPORTIONAL, INTEGRAL, AND DERIVATIVE (PID) CONTROL GAINS. DEVELOP AND TEST A CONTROLLER TO MAINTAIN A DESIRED  SPEED FOR THE MOTOR. ANSWER: Speed of a dc motor can change manually or by using automotive control systems External…

1) PROJECT :  Development of a Forward energy-based fuel Consumption Model of a Conventional Vehicle Submitted by : Manu Mohan V AIM :  To develop the block diagram of the vehicle model using simulink. To  define the script in MATLAB for running the simulink model.(ie load variables). Tabulate the fuel…

1) AIM DEVELOPMENT OF A FORWARD-BASED FUEL CONSUMPTION OF A HYBRID VEHICLE OBJECTIVES To find the fuel economy of UDDS and HWFET cycle. We will compare it with conventional vehicle.  Plot the time trace for engine, transmission input, transmission output and wheel speed on one plot With the help of subplots plot engine…

ANSWERS Lithium-Ion Batteries Lithium-ion batteries power the lives of millions of people every day. From laptops and mobile phones to hybrid and electric vehicles, the technology is growing in popularity because it is lightweight, energy dense and rechargeable.…

1) ANSWER1 Simulate the 3 test cases from the harness dashboard and write a detailed report on the results. The Test Sequence Variant block, which lets you choose which test has to be replicated, can be used to choose one of the three test conditions. The simulation below shows that the first variant was initially chosen.…

AIM Prepare a detailed battery pack drawing along with its enclosure. State your assumptions.   ABSTRACT In this Project, we'll figure out all the numbers needed to construct an EV battery pack. For our battery pack, we're going to use Cell: ANR26650M1-B. All electrical factors, including temperature, Depth of Discharge,…

1)   AIM For a 10 cell series lithium ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB. OBJECTIVE For a 10 cell series lithium ion battery model, simulate the thermal effects and compare life cycle performance at various…

1) AIM: To Develop a double-acting actuator model using Simscape Multibody and Simscape components OBJECTIVES To develop a hydraulic model(Physical model) to maintain and control the flow of working fluid. To develop a mechanical model having hydraulic cylinder and piston. Implement hydraulic and mechanical system together…

  AIM Define all the necessary properties to Connectors ,electrical connectors and mounting clip using electrical part design work bench. OBJECTIVES Create or download Connectors ,electrical connectors and mounting clip cad models. Create required geometrical parameters. Define part as connector. Define bundle…

1) P clamp bundle entry plane P clamp Bundle exit plane P clamp base plane selection P Clamp Support part definition Steps followed Import p clamp part in to the part design Define the work object Define the points and planes corresponding for bundle entry and exit. Go to the electrical part design and define support part.…

1) Electrically defined DT06-2S connector Electrically defined DT06-4S connector Electrically defined DT06-6S connector Electrically defined DT06-08SA connector   Geomertical arrangement of connectors before bundle routing Brach definition Creation of sub branch Routed bundle with connectors before coating…

1) Aim: Route  Harness A and Harness B layout in Electrical workbench. Make assumption for harness bundle diameters.  Electrically defined connector C-DTO6-4S Electrically defined connector C-DT04-4P Developed Harness B  Branch definition Annotation For developed bundle connections Harness A Assembly Design for Harness…

1) Electrically defined DT06-2S connector Electrically defined DT06-4S connector Electrically defined DT06-6S connector Electrically defined DT06-08SA connector   Geomertical arrangement of connectors before bundle routing Brach definition Creation of sub branch Routed bundle with connectors before coating…

                                                                      PROJECT -1 : Wiring Harness Routing on V16 Engine AIM Route the Wiring harness…

                                                 PROJECT -2 : Wiring Harness Routing on Car Backdoor PROBLEM DEFINITION Route the Wiring harness on Given car body and Prepare flatten view drawing…

1) AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. CLASS A SURFACE Check the connectivity of the Class…

1) AIM: Create the Switch Bezel  Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. CLASS A SURFACE   Check the connectivity…

  1) Part 1 for quick return mechanism   Part 1 Drafting for quick return mechanism Part 2 for quick return mechanism Part 2 Drafting for quick return mechanism Part 3 for quick return mechanism Part 3 Drafting for quick return mechanism Part 4 for quick return mechanism Part 4 Drafting for quick return mechanism…

AIM: Create the Coin Holder  Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. GIVEN A SURFACE Check the connectivity of the Class…

1) AIM: Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. CLASS A SURFACE Check the connectivity of the Class A Surface…

  1) AIM:  Create the Door trim Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. To Create the rib and screw bosses for the Door Trim Lower…

   1) AIM:  Create the B-pillar  component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Create Dog house using given master section GIVEN CLASS A SURFACE…

  1) OBJECTIVES Create the Door trim Panel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. To Create the Heat stakes and locators…