Tayler's Series Expansion  The Taylor series of a function is an infinite sum of terms that are expressed in terms of the function's derivatives at a single point , f(x+Δx) = f(x) + f'(x).Δx + f''(x).(Δx)^2/2! + f'''(x).(Δx)^3/3! + .......... Now finding the value of f'(x) , f''(x) in 4rh order…

AIM:  Solving the steady state and unsteady state 2D heat conduction by using the point iterative technique. Jacobian method Gauss siedol method Successive-over Relaxation method With absolute error criteria 1e-4.   STEADY STATE ANALYSIS The 2D steady state heat conduction equation with no heat generation is…

1D Sub-sonic and Super-sonic Nozzle by Using McCormack Method Objective: To simulate the isentropic flow through a quasi 1D subsonic-supersonic nozzle by deriving both conservative and non-conservative forms of governing equation and solve them by using McCormack Method in MATLAB.   NOZZLE DIAGRAM: The nozzle…

Solving the simulation of an incompressible-laminar-viscous flow through the backward facing step geometry.  performing 2 case studies as described below and comparing the results. Case 1 - Simulate the flow without using any grading factor (i.e., GF = 1) Case 2 - Simulate the flow with grading factor of…

FINITE VOLUME METHOD (FVM) LITERATURE REVIEW   Objective: To study and understand The difference between FDM and FVM. Interpolation schemes in FVM Flux limiters in FVM   Finite Volume Method (FVM) is a discretization method for the approximation of a single or a system partial differential equation (PDE) expressing…

                                                       2R FORWARD KINEMATIC ROBOT ARM   OBJECT: Write a program to solve forward kinematics of 2R Robotic Arm. THEORY: A robotic…

                                                    Solving second order ODEs  OBJECTIVE:                …

                                                                    GENETIC ALGORIYHM   OBJECTIVE:    To explain the concept of Genetic…

                                                                         MIXING TEE   AIM: To create two versions of the…

                                                                 FLOW OVER A CYLINDER       Aim: Simulation of flow over the cylinder and…

                                   Simulation of Flow through a pipe in OpenFoam   Objective: The aim of this project is to simulate the flow of water through a pipe and validate the results of the fully developed flow with analytical…

                                              External flow simulation over an Ahmed body   AIM: Describe Ahmed's body and its importance. Explain the reason for the negative pressure in the wake region.  Explain the significance of the point of separation.    INTRODUCTION: The pollution emerged by using volatile fuels…

                                                  CHT ANALYSIS ON HEAT EXHAUST PORT   Introduction: Conjugate Heat Transfer is process of heat exchanging at interface and transporting via conduction…

                                                                    Rayleigh-Taylor Instability   AIM: Simulation of Rayleigh-Taylor Instibility. …

                                                            CHT Analysis on Graphic Card Objectives: Run the simulation by varying the velocity from 1m/sec to 5m/sec for…

                                     Simulating Cyclone separator with Discrete Phase Modelling   Aim: To perform analysis on cyclone separator and calculate the separation efficiency and pressure drop.   Objective:…

                                                            PARAMETRIC STUDY ON GATE VALVE   Aim: Simulate the Gate valve using Parametric study. Objectives: Obtain…

                                                                      Simulation on Natural Gas AIM: To perform a combustion simulation on the…

                                                SURFACE MESHING ON A PRESSURE VALVE   AIM: Perform the Surface meshing on Pressure valve OBJECTIVES: Target length = 1mm, 3 mm and 5 mm (i.e.…

                                                               CFD MESHING ON TURBOCHARGER AIM: Perform surface mesh with the given target lengths as per PIDs for Turbocharger model.   OBJECTIVES: Blade stage-1 = 1 mm Blade stage-2 = 1 mm Impeller = 2 mm Shaft rotor = 1 mm Turbo casing = 5 mm Compressor casing = 5 mm Inlet…

                                                                    MESHING A BMW CAR MODEL   AIM: check and solve all geometrical errors and mesh…

                                                   SURAFACE WRAP ON AUTOMOTIVE ASSEMBLY AIM: Clear the geometry and merge all 3 models and perform surface wrap.   OBJECTIVES: Perform surface wrap merged geometry.                         Target length for Wrap = 3 mm   INTRODUCTION: Surface wrap is the process of meshing…

                                                            MESHING ON TESLA CYBER TRUCK   AIM: Perform meshing with the suitable Target length for cyber truck model.…

                                                        PARSING NASA THERMODYNAMIC DATA   AIM: Parsing the NASA Thermodynamic data in MATLAB and find the molecular weight of each…

    AIM: Create Rankine cycle simulator using the standard engg. Book.   OBJECTIVES:   Calculate the state points of the Rankine Cycle (any type of your choice) based on user inputs.  Then, plot the corresponding T-S and H-S plots for the given set of inputs.   INTRODUCTION: Rankine cycle…