Otto Cycle   OBJECTIVE Write a program to solve the air standard otto cycle in matlab. Plot the P-V diagram. Calculate the thermal efficiency of the engine     OTTO CYCLE An Otto cycle is an idealized thermodynamic cycle that describes the functioning of a SI piston engine.   PROCESS…

Solving second order ODEs   Problem statement The damped pendulum system is governed by  `(d^2 θ)/(dt^2 )+(b/m) dθ/dt+(g/l) sin⁡θ=0` Convert second order ODE to first order ODE by assuming `dθ/dt= θ_1` And `(dθ_1)/dt= θ_2` This implies `(dθ_2)/dt= (-b/m)θ_1-(g/l)sin⁡〖θ_1…

Optimization of stalagmite function Aim Write a code in MATLAB to optimize the stalagmite function and find the global maxima of the function. Clearly explain the concept of genetic algorithm and also explain the syntax for ga in MATLAB. Make sure that code gives the same output, even if it is made…

Parsing NASA thermodynamic data Aim Write a function that extracts the 14 co-efficients and calculates the enthalpy, entropy and specific heats for all the species in the data file. Calculate the molecular weight of each species and display it in the command window. Plot the Cp, Enthalpy and Entropy for the local…

Simulink challenge 2 Doorbell using solenoid   Objective Make a Simulink model of Doorbell using solenoid block with the following details: In the above arrangement, when the switch is closed the electromagnet receives electrical power from the battery and pulls the metal arm to hit the bell producing sound. …

Automatic washing machine Objective Implement control logic of a “washing machine” using State flow as per given sequence: If the power supply is available, the system gets activated If the Water supply is not available, stop the process & indicate through LED Soaking time should be 200s followed by Washing…

Baja ATV – CVT Objective To study the Continuous variable transmission system in BAJA – ATV   All terrain vehicle An all-terrain vehicle (ATV), also known as a light utility vehicle (LUV),[1] a quad bike, or simply a quad, as defined by the American National Standards Institute (ANSI); is a vehicle that…

Project 1 forward energy-based fuel consumption model of a conventional vehicle. Abhishek Patil | 07/03/2022 Objective To compute the fuel economy numbers for the given vehicle (kmpl) on the urban cycle (UDDS) and highway cycle (HWFET). Also, to analyze and understand the vehicle operating points in terms of engine speed,…

Project 2 Rankine cycle Simulator Abhishek Patil | 10/04/2022 Objective Create a Rankine Cycle Simulator using MATLAB. Then, plot the corresponding T-s and h-s plots for the given set of inputs. Title and axes labels are a must, while legends could be used if necessary.   Rankine cycle The Rankine cycle is…

Project 2 development of a forward energy-based fuel consumption model of a P1 hybrid vehicl Abhishek Anil Patil | 12/04/2022 Objective  Project 2 deals with the development of a forward energy-based fuel consumption model of a P1 hybrid vehicle. he main goal of this project is to understand the functionality of a…

Week 1 Challenge Understanding Different Battery Chemistry Abhishek Patil | 15/04/2022 Objective 1.Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium-ion cells. Give your detailed explanation on it 2.Compare the differences…

Week 7 State of charge estimation Abhishek Anil Patil | Introduction to battery technology | 26/04/2022 Objective   https://in.mathworks.com/matlabcentral/fileexchange/72865-design-and-test-lithium-ion-battery-management-algorithms 1.Simulate the 3 test cases from harness dashboard and write a detailed report on the…

Project 1 Mechanical design of battery pack Abhishek Anil Patil | Introduction to Battery Technology| 30/04/2022 Objective Battery pack capacity: 18 kWh Cell: ANR26650M1-B  Prepare a detailed battery pack drawing along with its enclosure. State your assumptions.   26650 Lithium-Ion Power Cell   Battery pack…

Project 2 Thermal modeling of battery pack   Abhishek Anil Patil | Introduction to Battery Technology | 01/05/2022 Objective For a 10-cell series lithium ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB.   Simulink…

Project 1 Mini Project on Vehicle Direction Detection Abhishek Anil Patil | 25/05/2022 General Overview: Identifying the direction of the vehicle is one of the important & diverse features in Autonomous driving & Advanced Driver Assistance Features. This particular sub-feature of identifying the direction of vehicle…

Adaptive Cruise Control   Abhishek Anil Patil | 26/05/2022 General Overview: Adaptive Cruise Control Feature for passenger cars allows the host vehicle to adapt to the speed in line with the flow of traffic. Driving in heavy traffic or keeping a safe distance to the preceding vehicle calls for a high level of concentration.…

Project 1- Traffic Jam Assistant Feature   Abhishek Anil Patil | 10/06/2022 General Overview: Traffic Jam Assistant Feature Introduction to the Feature: Traffic Jam Assistant is one of the most common feature in Advanced Driver Assistance System. Traffic Jam Assistant helps the driver arrive more relaxed at their…

Week 3 - 2D meshing for sheet metal   Abhishek Anil Patil | 15/06/2022 Objective For the given Hood model, Take the mid surface for all the components after checking the geometrical errors and mesh the mid surface with the given element Quality criteria. (Refer the table Below for the Quality criteria)    S.No  Quality…

Week- 5 - Solid meshing   Abhishek Anil Patil | 20/06/2022 Objective For the given Rear view mirror component, check for the geometrical errors and mesh the Surfaces with the given 2D element Quality criteria’s given below.    S. No  Quality Criteria  Value  1 Target/Average length  …

  Week - 4 - 2D meshing for Plastic components Abhishek Anil Patil | 23/06/2022 Objective Week 4 For the given Plastic Bottle Cap model, check for the geometrical errors and take the mid surface by suitable mid surfacing techniques. PID and Thickness assignment has to be done for all the mid surfaces. Mesh the same…

Week 6 - Creating connection for Rear door   Abhishek Anil Patil | Course Title | 24/06/2022 Objective This week, the connections for the front door by using different 1D elements are taught in detail.  Now for the given Rear door FE model, Create and Apply different PIDs for different components. By using the…

Week - 8 - Morphing   Abhishek Anil Patil | 30/06/2022 Objective 1) Practice all the Morphing techniques that were shown in the video for Model-1.  Click here to Download the Model-1 2) Perform morphing for the Model-2 and Increase the Height of the Dog houses and Ribs. (Refer Red annotations in the below image…

Tool Test-2   model       volume mesh