AIM: To calculate the mix design for M35 grade concrete with fly ash and M50 grade concrete without fly ash  INDRODUCTION:  Concrete mix design involves a process of preparation in which a mix of ingredients creates the required strength and durability for the concrete structure. Because every ingredient in the…

  AIM: - To prepare a Sketch  G+1 floor residential plan, according to Vaastu Shastra, - To list down the names of the structural drawings required to be provided to the site for construction. - To calculate the individual corresponding loads from the members as per IS code. INDRODUCTION: -Vastu Shastra…

   AIM:  -To create the geometrics of the given pictures as per their dimensions using all the co-ordinates system method from        line tool and circle tool if required  -To draw the profile and the trusses using any coordinate system methods   INTRODUCTION: AutoCAD is…

1) Aim: To draw c.s of load bearing wall showing foundation details PROCEDURE : • In the command prompt type QNEW • click on imperical template <advaced setup < decimal    In the command prompt type units     set the units • In the command prompt type REC specify first corner point…

  Q1) Aim: To draw the above figure using AutoCAD Procedure: Select the line command. Specify the Starting point as (0,0) in the command prompt and press enter. Specify the next point as (@3,0) in the command prompt and press enter. Specify the next point as (@2.12-45) in the command prompt and press enter. Specify…

1) Aim: To draw the layout of a residence plan. Commands Used: 1. XL-V OR XL-H.                           2. Offset                           3. Fillet.            …

q1) Aim: To create a column schedule, and to draw the column showing reinforcement of the columns in detail. Introduction:-The column schedule is a schedule which the details of column will be collected in the construction for design purpose. The columnscheduling is very important thing in column detailing. -Structural…

1) Aim: To draw the elevation and details of wardrobe. Introduction:  A wardrobe is a standing closet used for storing clothes. The earliest wardrobe was a chest, and it was not until some degree of luxury was attained in regal palaces and the castles of powerful nobles that separate accommodation was provided for the…

Aim: To sketch the Plan and sections of the given building Introduction: Floor plans are scale drawings that show the relationship between rooms, spaces and physical features viewed from above Exterior elevation drawings detail the exterior of a home. This provides information regarding where the windows, doors, and…

1) AIM:  -To create the templates and need to take the size of title block as per industry standards. -And need to save them as a block names as Customi_titlebox and Custom_titlebox. INTRODUCTION:  • Drawing template files are drawings that store styles, settings, layers, and layouts in a drawing including       title…

1)   Aim: To Create the Kitchen Layout as shown in the Figure Introduction: The kitchen layout is the shape that is made by the arrangement of the countertop, major appliances and Storage areas. This floor plan creates the kitchen's work triangle – the path that you make when moving from the refrigerator…

1) AIM: • To create a layout of the plan and section A of the project in challenge 7 using the template • And use the MV command to create the viewport of the size from the given figure. Introduction: • Plan and Sections are different types of drawings used by architects to graphically represent a building design and construction.…

1) AIM: To create a 3D Furniture element as given in the figure and need to assume dimensions which are missing in the drawing. INTRODUCTION: • The three dimensional furniture element was drawn in the autocad using the different tools in the autocad. • 3D models are widely used anywhere in 3D graphics and CAD.…

1) Aim : To create a 3D Isometric View of the building with plan and elevation as shown in question Figure using AutoCAD. Introduction:• 3D Wireframe Model:- A wireframe model is a skeletal description of a 3D object. There are no surfaces in a wireframe model and it consists of only points, lines, and curves that…

Aim:To draw the Residential Building in the plot size of 60' x 20' (18.3mX6m) facing East direction with the following drawings:• Architectural Drawing1. Site Plan2. Ground Floor Plan3. First Floor Plan4. Elevation5. Section• Structural Drawing1. Column Layout Plan2. Beam Layout Plan3. Footing Layout PlanIntroduction:The…

Aim: To create a Three Dimensional model of the residential building with a rendered view using AutoCAD INTRODUCTION: • 3D computer-generated images of proposed building projects and other types of constructions are widely used by architects and designers to showcase their designs to clients. • The steady advancement…

Question 1 :- From the file menu, create a new project (Structural / Architectural / Construction template) and name the project appropriately. AIM: To create a new project Structural/Architectural/Construction template and name the project appropriately. Intoduction: • Revit is BIM(Building Information Modeling) software…

Question 1:- What is BIM? Summarize the features of BIM and benefits of using BIM over 2D CAD tools. • BIM is an acronym for Building Information Modeling or Building Information Management. • It is a highly collaborative process that allows architects, engineers, real estate developers, contractors, manufacturers and…

 1)Use the project file created from Week 2. Based on layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with grids created from week 2. Procedure : • Double click…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level Procedure : • Double click on the Revit application icon and opens the app. • Click on "Open" in the Home page. • Open the saved "week 3 project"…

1) Why are building codes or standards essential for the modeling/ efficiency of drawings in Revit ? • The National Building Code (NBC) is a standardised set of rules to be followed by authorities and construction firms, to provide ahealthy and safe living experience for all residents.• The NBC of India, a comprehensive…

1) Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project AIM: To create a project base point and project shared coordinates for the project in architectural template. INTRODUCTION: In revit, under manage toolbar their is a option to specify/establish/define…

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School • Multi-Unit Residential Apartment   2) Assume reasonable assumptions for geographic…

1) What are HVAC systems? Why are they essential in the modeling of buildings • HVAC stands for Heating, Ventilation and Air Conditioning. • HVAC refers to the different systems used for moving air between indoor and outdoor areas, along with heating and cooling in both residential and commercial buildings. • HVAC are…

1) Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below           a. Using 3D model create a section box           b. To create similar doors and windows in a floor plan layout         …

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. AIM: To create a set of sinusoidal points, create a curve and provide surface to the curve. INTRODUCTION: A sine wave or sinusoidal wave is the most natural representation of how many things in nature change state.…

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class AIM: To export the revit architecture and structure model to navisworks cache file. INTRODUCTION: Used primarily in…

1)What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate a) MODE OF FAILURE- Flexural tension failure This failure occurs when the load on beam exceeds its flexural capacity.Here failure starts by yielding steel reinforcement followed bycrushing of concrete at compressive…

Question 1: Compute lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The system has 3 DOFs as shown. Assume L = 2h and Elb = Elc     Question 2: a)For the following structures: Determine the number of degrees-of-freedom for dynamic analysis Establish the…

Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental period of vibration (T1 = 2 seconds) and…

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility.   AIM: To Comment on the layout concerning earthquake resistance in…

Question 1: The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account the restraint…

Challenge 6 – ETABS modelling of a 25 storey building Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. Structural Element Sizes …

Given details: Model a 10 different building of various storey on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive storeys has a storey height of 3 metres. Structural Element Sizes  Beams : 300 ×…

Challenge 7 – Detailed design of concrete buildings -1 Detail design of beams in Etabs 2018.The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1)…

 Reinforcement detailing of columns in Etabs 2018. The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment Resisting Frame. The following challenge deals specifically with two columns at the following grid intersections. 3A 3B Provide details of longitudinal reinforcement for the…

 The etabs file for a G+6 building is provided. Run the analysis and design the RCC shear walls (show in the etabs model). The following challenge deals specifically with the shear wall of size 300x1500 at grid A-11 in the structural model. Extract values of longitudinal steel ratio, boundary element length and shear…