Screenshot of Draft Analysis Report for Class-A Surface and The Final Plastic Component :-  Class-A Surface -    Final Component -  Screenshot of Solid Model With Colour Code of Draft Angle in Different Orientations -  Isometric View -  Front View -  Top View -  Side View - …

DRAFT ANALYSIS OF CLASS-A SURFACE :-  DRAFT ANALYSIS OF FINAL COMPONENT :-  Screenshots of the solid model with the proper color code of the draft angle in various orientations :-    REPORT :-  Steps to Create Tooling Axis -  First of all we take an intersection of Class-A Surface and create…

UNDERBODY COATING  Underbody Coating is usually a dense cladding applied uniformaly on undercarriage portion of a automobile. it is usually done by the sprayed or painted when it just out of dealership and is clean. But, we can also apply the undercoating after a couple of year. so, it can further prevent damage the…

BENCHMARKING :- In Automotive Industry Benchmarking is in the sense of comparison between similar products. it may be the comparison of performance, features and specifications. it is used by businesses to compare the key metrics of their operations to those of other companies and remain competitive in the market. …

                                                             REPORT ON HOOD ASSEMBLY DESIGN  AIM The aim of this project is to design a Hood Assembly which consists…

                                                            REPORT ON SECTION MODULUS Aim The aim of this report is to calculate the section modulus of the designed…

                                                    REPORT ON FENDER DESIGN Aim   Introduction Before we go for the design of fender let's try to understand the concept of fender and…

                                                        REPORT ON WHEEL ARC MEASUREMENT Aim The aim of this report is to calculate the wheel arc area and compare to the European Regulations Requirement to check whether it satisfy or not.  Introduction  Wheel arch is the semi - circular part of the vehicle is position on…

                                                                REPORT ON ROOF DESIGN AIM The aim of the project is to create the Roof Sheetmetal design…

                                                        REPORT ON ASSEMBLY DESIGN AIM The aim of this design is to create the part model seperately and then assemble them as a…

                                                                 REPORT ON BUMPER DESIGN AIM The aim of this Bumper Design is to create a bumper model from the given class- A Surface. Also create the proper tooling direction and do draft analysis on both the class- A surface and final component.  INTRODUCTION A bumper…

                                                                       REPORT ON RIBS AND SCREW BOSS AIM The aim of ribs and screw bosses design…

                                                       REPORT ON DOG HOUSE DESIGNAIMThe aim of this design is make a solid body from given class-A surface and then create the dog houses…

                                                       REPORT ON DOOR TRIM LOCATORS AND HEAT STAKES  AIM The aim of this design is to create the closed body from the given class-A…

                                                           REPORT ON BACK DOOR DESIGN AIM The aim of this project is to design the back door outer panel, inner panel and…

AIM Define Electrical Connector using Electrical Part design Workbench and also define all the necessary properties to Connectors & Clip from the given data. INTRODUCTION Wiring Harness -  Connectors -  Let's Define the given data into electrical connector -  1. Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html)…

AIM The aim of the project is to study and understand the different models of the clips, back shell and corrugated tube and convert the given cad data file of the P clamp into electrical support and Backshell into the electrical back shell by electrical Part design workbench available in the CATIA V5 tool. Then create…

AIM Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram.   Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end)   Download…

                                                              REPORT ON A PILLAR DESIGN AIM The aim of this project is to design the A - Pillar from the given class-A…

AIM To create the assembly wiring harness as per the image given below. Convert all the given part files into CAT.Part file and define all into electrical component and also define all the electrical features. Create Harness Assembly and check for Connectivity and also check for warnings. create annotation for all the…

AIM Flatten the harness assembly completed in “ week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view. PROCEDURE Define all the connectors as electrical component and electrical features for them. Then create harness assembly…

                                                                FINAL PROJECT REPORT AIM The aim of this project is to make a solid body of a side door trim…

                                                       REPORT ON FINAL PROJECT 2 AIM The aim of this project is to route the wiring harness on the given backdoor of a car and prepare a flattened view drawing in the CATIA V5 by applying all packaging rules and following the industry standards and design guidelines. INTRODUCTION…

                                                           REPORT ON FINAL PROJECT 1 AIM The aim of this project is to route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design.…