Aim - To simulate and compare the mixing effectiveness of two free streams at different temperatures and velocities in a T-section pipe on CFD Fluent with the help of k-ε model and SST k-ω model. Introduction - A T-section pipe is a component used commonly in systems where fluid flow takes place.…

Aim- PART-I To simulate a flow over cylinder and calculate Strouhal number for Reynolds number = 100 using a steady and transient solver sequentially. PART-II  To calculate the co-efficient of drag and lift over a cylinder by setting the Reynolds number to 10, 100, 1000, 10000, 100000 with just the steady solver,…

Aim- To simulate the flow of air over an Ahmed body and perform a grid independency test.   Introduction- Ahmed body is a standard model of a generic car used to test simulations. Instead of bringing in the proper model of the actual car to be simulated, the Ahmed body serves best. Ahmed body represent a…

Aim- To simulate Rayleigh-Taylor instability. Introduction- Rayleigh-Taylor instability is an instability that occurs when two different fluids of different densities have a common interface and the lighter fluid pushes the heavier fluid. An example from school is the famous water and oil behaviour in a container…

Aim - To perform a CHT analysis on an exhaust port of an automobile and calculate the heat transfer co-efficients from the results. Introduction - Conjugate Heat Transfer analysis is a method of simulating heat transfer between a solid and liquid by exchanging thermal energy between their interfaces. Application…

Aim- 1. To simulate CHT on a graphics card.          2. To check the temperature distribution on the graphics card and advise appropriate construction to avoid overheating. Introduction-  Conjugate Heat Transfer Analysis or CHT analysis is done in a domain where a combination of modes…

Aim- To perform analysis on cyclone separator and calculate the separation efficiency and pressure drop. Introduction- A cyclone separator is simply a separation device used for gas-solid flow. This flow needs to be filtered from the particulate matter. The principle on which this device works is simply inertia, where…

Aim- To perform a parametric study on the gate valve simulation by setting the opening from 10% to 80%. Introduction- A gate valve, also known as a sluice valve, is a valve that opens by lifting a barrier (gate) out of the path of the fluid. Gate valves require very little space along…

Aim-  1. To perform a combustion simulation on the combustor model and plot the variation of the mass fraction of the different species in the simulation using line probes at different locations of the combustor. To plot for CO2, H2O, CH4, N2, O2, NOx emissions & Soot formation. 2. To add the water content in…

Aim- To study the aerodynamics of airfoil body by varying the angle of attack. Introduction-  Airfoil- Airfoil, also spelled Aerofoil, shaped surface, such as an airplane wing, tail, or propeller blade, that produces lift and drag when moved through the air. An airfoil produces a lifting force that acts at right…

Aim- To write a program that solves the following ODE. Write a program in Matlab that will simulate the pendulum motion.   Theory- A second order ordinary differential equation is an ordinary differential equation in which any derivatives with respect to the independent variable have order no greater than 2. The general second…

Aim - To write a code in MATLAB to optimise the stalagmite function and find the global maxima of the function.                                                          …

Aim - To write a function that extracts the 14 co-efficients and calculates the enthalpy, entropy and specific heats for all the species in the data file. Calculate the molecular weight of each species and display it in the command window. Plot the Cp, Enthalpy and Entropy for the local temperature range (low temperature…

                                                                                          DESIGN…

Radar mast     REPORT Yacht Model Objective- To model all the components of a Sunseeker Superyacht and render them after assembly in SolidWorks 2020. Introduction-  A yacht is a motor boat or vessel used for pleasure, cruising or racing. It is a boat which has amenities to accomodate  overnight use. To…

Draft Angle A draft angle refers to that slant applied to the sides of most features of injection molded parts. Positioning of the injection angles is such that they run towards the direction of the mold's pull and parting line. They help to release the molded parts from the mold easily.   Tooling Axis …

1. Class A Draft Analysis   2. Solid Body Draft Analysis   3. Final Body   4. Tree structure   5. Class A surface   6. Class B surface   7. Class C surface   8. Tooling Axis   9. Report on Draft Analysis and Tooling axis creation   i. Tooling axis creation Step1: Acquire the…

1. Tooling Axis   To create the tooling axis the intersection of component is generated with the respective planes (x and y). Since the walls of the coin holder are at 90 degrees or perpendicular to each other the tooling axis is simply created by drawing a line normal to the base.   2. Draft Analysis The Draft…

1. Draft Analysis The Draft Analysis command enables you to detect if the part you drafted will be easily removed. This type of analysis is performed based on color ranges identifying zones on the analyzed element where the deviation from the draft direction at any point, corresponds to specified values. For the color…

1. Report on Draft Analysis and Tooling axis creation   i. Tooling axis creation Step1: Acquire the cross-section outline of the component from the x-direction using the intersection command. Select the component and the appropriate plane and click 'OK' in the command. Extend the line which is closest to the…

1. Draft Analysis The Draft Analysis command enables you to detect if the part you drafted will be easily removed. This type of analysis is performed based on color ranges identifying zones on the analyzed element where the deviation from the draft direction at any point, corresponds to specified values. For the color…

1. Draft Analysis The Draft Analysis command enables you to detect if the part you drafted will be easily removed. This type of analysis is performed based on color ranges identifying zones on the analyzed element where the deviation from the draft direction at any point, corresponds to specified values. For the color…

1. Draft Analysis The Draft Analysis command enables you to detect if the part you drafted will be easily removed. This type of analysis is performed based on color ranges identifying zones on the analyzed element where the deviation from the draft direction at any point, corresponds to specified values. For the color…

1. Sketches   2. Tree Structure-   3. A-Pillar closed body with Tooling axis-    4. B-side feature (Dog House) using the Master section & Side core Axis-   5. Draft analysis i. Class A   2. A-pillar   3. Dog House using Side core axis   6. Individual entities i. Class A (given)…

Title- Advanced Sheet Metal Design Using NX Cad Objective- To design a Casing using NX Sheet Metal Application with its various features. Introduction-  Sheet metal is metal formed into thin, flat pieces, usually by an industrial process. Sheet metal is one of the fundamental forms used in metalworking,…

Benchmarking-  Benchmarking involves a structured comparison between similar products, services or processes on some dimensions of performance. For example it can be used to compare the availability and delivery of features in a product and in this form often provides the basis of consumer tests and reviews. These…

Undercoating is a thick resilient coating applied to the underbody or chassis of an automobile to protect against impact damage from small stones, which would rapidly chip ordinary paint, allowing rusting to begin. The main purpose of undercoating is to check rust especially in the body…