1. Concrete mix design for M50 grade concrete without Fly ash Data assumed: I. Stipulations of proportioning: a) Grade designation : M50 b) Type of cement: OPC 43 grade conforming to IS 8112 c) Maximum nominal size of aggregate: 20mm d) Minimum cement content: 360 kg/m^3 (From Table 5 of IS 456: 2000- Exposure condition)…

1. I have drawn the plan on A4 size paper according to Vaastu Shastra    Schedule of openings Doors ,    D= 1x2.10m               D1= 0.9x2.10m               D2= 0.75 x 2.10m Windows, W= 1.2x1.37m        …

P1 & P2 AIM To draw the geometric object P1 & P2 using all the co-ordinate system methods, they are absolute co-ordinates, relative rectangular co-ordinates and relative polar co-ordinates. INTRODUCTION Absolute Co-ordinate system is a system in which drawing the object by 2 co-ordinates x-axis, y-axis. Relative co-ordinates…

1. CROSS-SECTION OF LOAD BEARING WALL AIM To draw the cross-section of Load bearing wall over spread footing by using AutoCAD software INTRODUCTION This type of drawing can be drawn by using the line command or rectangle command with specifying the length and angle of the drawing PROCEDURE Open AutoCAD software Choose…

1. AIM Drafting the given geometrical figure using Chamfer or fillet option in AutoCAD by decimal system INTRODUCTION This type of drawing can be drawn by using the line, Circle, Chamfer or fillet command with specifying the length and angle of the drawing given in figure PROCEDURE Open the AutoCAD software and dick on…

1. RESIDENCE PLAN AIM Sketch the layout of a residence, consider all dimensions as reference to sketch the unit plan. Also, the text in the layout is only for reference. Assume the missing dimensions. Also, refer the schedule for size of the doors INTRODUCTION The Residence plan can be drawn with help of some important…

1) AIM Create a column schedule as shown in the figure using AutoCAD INTRODUCTION This type of drawing can be drawn by using the line, text, rectangle command with specifying the length and angle of the drawing given in figure PROCEDURE Open the AutoCAD software and dick on new for a new drawing sheet Enter units in command…

1. AIM To draw the elevation and details of wardrobe using AutoCAD 2022 INTRODUCTION A wardrobe is a standing closet used for storing clothes. The earliest wardrobe was a chest, and it was not until some degree of luxury was attained in regal palaces and the castles of powerful nobles that separate accommodation was provided…

1. AIM To draw the floor plans and sections using the proper dimension techniques and dimension styles to document the project. INTRODUCTION Plans and Sections are different types of drawings used by architects, to graphically represent a building design A plan drawing is a drawing on a horizontal plane showing a…

AIM To draw Architectural Drawings of Floor Plan, Elevations, and Sections and also the Structural Drawings of Column, Beam and Footing Plan INTRODUCTION Architectural and structural drawings are generally considered to be the drawings of steel, wood, concrete and other materials used to construct buildings, ships, planes,…

1. AIM To create the templates and need to take the size of title block as per industry standards and need to save them as a block name as Custom 1_titlebox and Custom 2_titlebox INTRODUCTION Drawing template files are drawings that store styles, settings, layers, and layouts in a drawing including title blocks When you…

1. AIM To create the layout of the kitchen and providing hatches to it using the autocad in detail. INTRODUCTION kitchen layout is the most important part of designing your perfect kitchen. It's the layout that will determine how you cook, how you eat and how you socialise So whether you're totally remodelling the kitchen,…

1. AIM To create a layout of the plan and section-A of the project in challenge 7 using the template And use the MV command to create the viewport of the size from the given figure. INTRODUCTION Plans and Sections are different types of drawings used by architects, to graphically represent a building design A plan drawing…

1. AIM To create a 3D furniture element as given in the figure and need to assume dimensions which are missing in the drawing. INTRODUCTION The three-dimensional furniture element was drawn in the autocad using the different tools in the autocad 3D models are widely used anywhere in 3D graphics and CAD Their use predates…

1. AIM To create a 3D Isometric view of the given building with plan and elevation INTRODUCTION As isometric drawing is 30 representations of an object, room, building or design on a 2D surface. One of the defining characteristics of an isometric drawing. compared to other types of 30 representation, is that the final…

AIM To create a 3-dimensional model of the residential building with a rendered view INTRODUCTION: 3D computer-generated images of proposed building projects and other types of constructions are designers to showcase their designs to clients The steady advancement in computer graphics has enabled the creation of realistic…

1.AIM To create a new project from the file menu and need to name the project appropriately. INTRODUCTION For creating a project, select a template from the Projects list or the New Project dialog box To configure the project, choose Manage Project Information and enter information in the Project information dialog box.…

1. Building Information Modeling (BIM) BIM is an acronym for Building information Modeling or Building Information Management. It is a highly collaborative process that allows architects, engineers, real estate developers, contractors, manufacturers, and other construction professionals to plan, design, and construct a…

1. AIM To create a floor plan and need to apply the materials and thickness using the property browser to align the floor plan with grids created from week 2 INTRODUCTION Building material is material used for construction. Many naturally occurring substances, such as clay, rocks, sand, and wood, even twigs and leaves,…

1. AIM To model a Celling from the architecture tab above the walls at the first-floor level INTRODUCTION The creation of Celling’s within Revit is a very similar process to that of Floors and Roots- le you can let Revit do most of the work and "grass" where you want the boundaries to be. Or you can enter Sketch…

1. Ans Building codes essential for the modeling/efficiency of drawings in Revit Building codes address many of a society's most important concerns, including public health and safety, and environmental protection Building codes are used, when we are constructing a building, it gives the standard codes, that prevents from…

1. AIM To set project base point and project shared coordinates for the project using manage tab in the architectural template. INTRODUCTION The project base point can be used to establish a reference for measuring distances and positioning objects in relation to the model Initially, in stock templates, it identifies the…

1.Ans: A) I Choose Multi-Unit Residential Apartment 2.Ans Assumptions for geographic and location details for your project modeling My building is constructed in the residential area My building is constructed in the plain area (geographic) As per the NBC, the height limit will be given in NBC part V-1. (National building…

1.Ans HVAC SYSTEMS (HEATING, VENTILATION, AND AIR CONDITIONING) HVAC systems are responsible for the regulation of heat, airflow, ventilation, and air conditioning of an entire building you won't see the machines when you enter the building but you will most certainly fool the effects of a comfortable and well-ventilated…

1.Ans The shortcut keys for the given question is given below Using 3D model create a section box=BX To create similar doors and windows in a floor plan layout=CS To reduce the thickness of lines visible in plan views=TL To apply override settings to a floor in the model section view=VG To increase the range of visibility…

1.AIM To create a set of sinusoidal points, create a curve and to create a surface out of the curve INTRODUCTION Dynamo is a visual programming tool that works with Revit Dynamo extends the power of Revit by providing access to the Revit API (Application Programming interface) in a more accessible manner. Rather than typing…

1.AIM To Export the Revit architecture and structure model to Navisworks Coche files following the export settings INTRODUCTION Navisworks Cache Files are created mostly for ease of use and speed When you open a model created in other programs, it creates a cache file that is much smaller in size and you won't even notice…

1.Ans 1a. AIM To identify the mode of failure or damage of the beams in the given figure OBSERVATIONS Concrete crushed and the reinforcement is exposed. Concrete spalled beyond the reinforcement which may be a sign of rupture. Beam top portion looks safe because of the flange advantage from slab. The crack develops from…

1.AIM To Compute lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The system has 3 Degree of freedom as shown. Assume L = 2h and Elb = Elc SOLUTION By using Moment distribution method Given the Degree of freedom is 3 Now, The Unit Displacement U1=1, Where U2=U3 Stiffness coefficient…

1.Ans AIM  A five storey structure with 5 translational DOF is given here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. Also, calculate the effective modal mass Mn* and the…

1.Ans Investigation of the framing plan with respect to Symmetry in X-direction: If we split the plan vertically half, it will look mirrored. So, we conclude the given plan is symmetric in X-direction. It is observed that the distribution of mass stiffness is across the plan has good symmetrical aspects. This tends to…

1.Ans For Arrangement (a) Restraint of Floor shrinkage Observation: Full restraints at all corners Conclusion: Arrangement (a) will have higher restraint to shrinkage, thus lead to cracks in the floor.   The Lateral stiffness Observation: Comparatively Lower Lateral stiffness in both X and Y   Torsion with respect…

1.Ans AIM To Model a 25-storey building on ETABS with structural properties as specified below and to cross check the parameters as per 1S -1893 Provisions. PROCEDURE STEP-1 Go to ETABS software click on the file menu click on create new model option A new model dialogue box will be open as model initialization. Select…

1.Ans AIM: - TO STUDY AND COMPAIR THE RESULTS ON, Factors influencing the dynamic characteristics of different storey building for seismic force Factors influencing the Natural Period of different storey building for seismic force Factors influencing the Mode shape of oscillations of different storey building for seismic…