CONCRETE MIX FOR M35 GRADE WITH FLYASH a) Grade designation : M35 b) Type of cement: OPC 43 grade conforming to IS 8112 C) Maximum nominal size of aggregate : 20mm d) Minimum cement content: 320 kg/m^3 (From Table 5 of IS 456: 2000 Exposure condition) e) Maximum water-cement ratio : 0.45 (From Table 5 of IS 456: 2000 Exposure…

AIM - To Sketch a G+1 floor residential plan, according to Vaastu Shastra, and list down the names of the structural drawings required to be provided to the site for construction                                  GROUND FLOOR PLAN …

AIM- Draw the geometries using all the coordinates system methods INTRODUCTION-cordinate system Absolute cordinate system-In absolute cordinate system all the points are located from the origin Relative cordinate system- In relative cordinate system the points are located with respect to the previous point Polar cordinate…

AIM To draw the given figure in autocad Fig 1 PROCEDURE SELECT line command specify the first point eg-(1,1) follows the series of command (@0.9,0)(@0,0.25)(@-0.2,0)(@0,0.4)(@-0.05,0)(@0,0.4)(@-0.05,0)(@0,0.6)(@0,0.05)(@0,1)(@-0.3,0)(@0,-1)(@0,-0.05)(@0,-0.15)(@-0.3,0)(@0,-0.15)(@-0.3,0)(@0,-0.15)(@-0.3,0)(0,-0.15)(@1.15,0)(@0,-0.25)(@-0.05,0)(@0,-0.4)(@0.2,0)…

AIM To draw the given figures in autocad FIG1 PROCEDURE SELECT the line command specify the first point follow the series of command (@3,0)(@2.12<45)(@2.83<135)(@2<180) close select circle with center (1.5,1) from origin with radius 1.2 and press enter select circle with center (1.5,2.5) from the origin with radius…

Challenge one Challenge two Procedure select a circle command specify the center draw a circle of radius 452mm with the same center draw a circle of radius 1398 mm place the chairs symetrically between the two circles RESULT Challenge three    

1) AIM - To Create a column schedule with the help of lines Procedure 1) create the table with the help of line 2) allot the text in the position Result 2) AIM- TO Create a window schedule as given Procedure 1) create the table with the help of line 2) allot the text in the position Result 3) AIM- TO Create the drawing…

A) AIM- TO Draw the elevation and details of a wardrobe as shown in the Figure PROCEDURE- SELECT the line command draw the elevation as per the dimension given select the DIMENSION tool give the dimension  select the TEXT tool alot the specified position to the text in the figure RESULT B) AIM -Draw the floor plan…

1) AIM- TO Create the Plan and Sections as shown PROCEDURE- SELECT the line command draw the LAYOUT as per the dimension given select the DIMENSION tool give the dimension  select the TEXT tool alot the specified position to the text in the figure RESULT 2) AIM- TO Create the Plan and Sections as shown PROCEDURE-…

AIM- To Design and Draft a layout of a residential building INTRODUCTION- floor plan- or house plan is a simple two-dimensional (2D) line drawing showing a structure's walls and rooms as though seen from above elevation- refers to an orthographic projection of the exterior (or sometimes the interior) faces of a building…

1) AIM- Create the templates as shown in Figures also create a block of this template name as Custom1_titleblock and Custom2_ PROCEDURE SELECT the line command  using line command create the template as shown in fig select single line text from annotate and mention the text as shown select block command using command window …

1) AIM-Create the layouts of the Kitchen and provide hatches pattern as shown and also use blocks and appropriate dimensions  PROCEDURE  SELECT the line command  using line command create the kitchen layout as shown in fig select single line text from annotate and mention the text as shown select dimension  tool mention…

1) AIM-Create a layout of the Plan and Section A also using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use ATTEDIT command to edit the information in the title block. Use A1 size for the layout PROCEDURE open file of…

1) AIM-Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing PROCEDURE select 3d modeling from the settings create the 2d figure as per the given dimension use join command or union command to create 2d polygen create 3d solid fig of 2d polygen using region command use extrude and give…

1) AIM-Create a 3D Isometric View of the building with plan and elevation given PROCEDURE select 3d modeling from the settings create the 2d figure as per the given dimension use join command or union command to create 2d polygen create 3d solid fig of 2d polygen using region command use extrude and give the heght as per…

PROJECT AIM- To Create a 3 dimensional model of the residential building with a rendered view INTRODUCTION- In planning of residential building floor plans , elevation and section elevation along with the center line diagram are made in order to figure out the exact positions of the rooms and footings in order to avoid…

1) AIM- create a new project From the file menu and name the project appropriately PROCEDURE- open the revit software  below models click on option new select architecture press ok go to file  go to save  select the path and give the name to save the file RESULT Saved file can been seen in…

Ans1) Revit buildings are of three types    a)view elements   b)model elements   c)annote elements annotation elements datum elements BIM is a visual representation of the physical and fuctional characterstics of a facility from inception onwards as such it serves as a shared information respository…

Ans1 AIM-Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with grids created…

ANS1) AIM- Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level PROCEDURE Go to aritectural -> celling-> automatic celling revit automatically place the cellings above the rooms RESULT ANS2) AIM-Model a…

ANS1 A set of standards that are uniform to all structures. It protects the construction safety Modern construction methods Provides building standards ANS2 Group A: Residential buildings Group B: Educational buildings Group F: Business buildings Group G: Storage buildings Group C: Assembly buildings Group H:Industrial…