TITLE:- BASE BRACKET DESIGN AIM:- To create the Base Bracket Plastic component through the given class-A surface and perform the draft analysis on the final component. OBJECTIVES:- Creation of tooling axis for given class – A Surface. Creation of Class B and Class C surface Perform Draft analysis for given class…

TITLE :- SWITCH BEZEL DESIGN AIM :- To create the Switch Bezel Plastic component through the given class-A surface and perform the draft analysis on final component and Class A surface. OBJECTIVES :- Creation of tooling axis for given class – A Surface. Creation of Class B and Class C surface Perform Draft analysis…

WEEK 9 CHALLANGE 3 BUMPER DESIGN :- AIM :- To create the bumper plastic component through the given Class A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. INTRODUCTION:- A bumper…

RIBS & SCREW BOSS CREATION  AIM:- To create the rib and screw boss for the door handle considering the design rules for the rib creation and screw boss creation and then perform the draft analysis for class A and final cmponent. Objectives:- Creating a tooling axis using bisecting method. Performing draft analysis…

TITLE:-  To create the Door Trim with attachement features (Dod House) considering the design rules. Consider the thickness of the part to be 2.5 mm. AIM :- To create the Door Trim with attachement features through the given class-A surface and perform the draft analysis on final component and…

TITLE :- DOOR TRIM LOWER WITH ENGINEERING FEATURES AIM:- Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Create…

TITLE:- A PILLAR DESIGN WITH MASTER SECTION AIM:- Creating A Pillar design with given master section and also creating B side features according to the given master section. OBJECTIVE:- Create Tooling Axis Perform Draft analysis for Class A surface and Final component. Create closed body Follow the master section and create…

BENCHMARKING :- Benchmarking involves a structured comparison between similar products, services or processes on some dimensions of performance. For example it can be used to compare the availability and delivery of features in a product and in this form often provides the basis of consumer tests and reviews. These look…

Underbody coating:- Underbody coating is a protective layer applied to the underside of a car to prevent damage from the elements, such as moisture, salt, and other chemicals. It is usually made of a rubber or polymer-based material that adheres to the surface of the car, creating a barrier between the metal body and the…

DRAWING 1:- INPUT:- PROCEDURE:- 1.) First make each solid part using part workbench using 2D drawing sheet data. 2.)Create 2D drafting of each part using drafting workbench. 3.) Now the important point is to assemble all the parts using assembly workbench. 4.) Go to assembly workbench and select new product. 5.)Now, I…

Aim: To design a car hood in NX CAD/CATIAA V5 using the given master section and provided design parameters. Hood and its components: Hood:- A car hood, also known as a bonnet in some countries, is a hinged cover that is located at the front of a vehicle and covers the engine compartment. It is designed to protect…

DESIGN OF FRONT FENDER- OBJECTIVE- To develop the front fender using Nx cad/Catia V5 following the design parameters. INTRODUCTION: A fender (also known as a wing or quarter panel) is the body panel that covers the wheel well and is located above the tire. Its primary function is to protect the wheel and tire from…

Aim:- Calculate the Wheel Arch gap at the required points and check whether the car passes the European standard. Objectives:-  Brief information about Fender. Different standards for wheel arch gap measurements. Calculate the Wheel Arch gap at the required points and check whether the…

Objective:- Create a roof assembly by developing the essential flanges for the outer roof and creating the reinforcements. Perform the draft analysis. Do a curvature study on the roof and perform calculations to determine the position of the Bow-roofs. Calculate snow load prediction value. ROOF - A roof…

Objective:- Using the section of the hood design and calculating the section modulus. Writing a detailed report on Section Modulus. Come up with a new section that has an improved Section Modulus compared to the previous one and mention what changes you come up with a new section that has an improved Section Modulus compared…

Design of Backdoor Objective:  To design the Back door of the car using the given Class ‘A’ surface. Introduction:- It is a hinged board or door at the rear of the vehicle that can be moved up or down during loading and unloading. Back Door is also referred to as 'Hatch' or 'Tailgate' or 'Trunk-lid' or…

Development of a Door Trim panel OBJECTIVE: Creation of CAD model considering the following inputs as like in OEM and tier1 companies  Class A surface  Nominal thickness: Refer to master sections  Attachment strategy :  Find an attachment strategy for the door panel complete work. Use Push pin with…