Two-quadrant chopper calculator: EV steady-state speed, regenerative braking and armature ripple

At a 70% duty cycle a 72 V two-quadrant chopper puts 0.7 × 72 = 50.4 V on the motor. The motor line T = 70.56 − 0.98ω meets the road load 24.7 + 0.0051ω² at 38.915 rad/s (371.6 rpm), 32.42 N m and 46.3 A. Change any number and the calculator redraws the operating point, the braking with d2 and the current ripple. Free, runs in your browser.

The defaults are the Week-6 EV Drivetrain challenge in Skill-Lync's hybrid electric vehicle course. Skill-Lync read 868 public reports on it: 427 give the right speed in their text and 96 give 38.85 rad/s, a number that solves neither quadratic they write. "Check my numbers" in the third tab tells you which slip yours is.

NPTEL Fundamentals of Electric Drives (IIT Kanpur) · CSJMU chopper notes · Husain, Electric and Hybrid Vehicles · checked against a separate solution (712 checks at build) · Updated 22 Nov 2026

The challenge gives no gear ratio or wheel radius, so its speed is the motor shaft speed. Fill both to get km/h from your own numbers.

Speed38.915 rad/s371.6 rpm
Torque32.42 N mmotor = road load
Armature current46.3 A11.6% of rated
0255075100d1 0.7: 38.91 rad/storque (N m)dashed: d1 0.2 to 1.0, orange: road load020406080100motor speed ω (rad/s)
0255038.91 rad/sspeed ω (rad/s)moves above d1 = 0.2450255046.32 Aarmature current (A)rated 400 A is off the scale00.20.40.60.81duty ratio d1
  • Operating point 38.915 rad/s = 371.6 rpm, 32.42 N m. The other root, −231.07 rad/s, is rejected: a negative speed is not forward motoring on this load curve.
  • Armature current 46.32 A, 11.6% of the 400 A rating.
  • Armature voltage 50.4 V average (d1 × 72 V), 70% of the rated 72 V.
  • Back-EMF 27.24 V. From the battery 2,334 W (average battery current d1 × Ia = 32.42 A), 1,073 W lost in Ra, 1,262 W at the shaft: 54.0% (= E/Va, ideal chopper).
  • No gear ratio or wheel radius is given in the challenge, so the speed is the motor shaft speed. Type both to get km/h.
  • Starts moving above d1 = 0.245. Top speed at d1 = 1: 59.33 rad/s (567 rpm). 50 rad/s needs d1 = 0.858.

What is the EV's steady-state speed if the duty cycle is 70%?

38.915 rad/s at the motor shaft, 371.6 rpm. In steady state the motor torque equals the vehicle's load torque, so the operating point is where the motor's torque-speed line crosses the road-load curve. The chopper's average output sets the line:

With constant flux, the armature current is the voltage left after the back-EMF, over Ra, and the torque is K-phi times the current:

Set it equal to the road load the challenge gives:

The negative root is the motor running backwards, which this load curve and this quadrant don't describe, so it is rejected. Then:

46.3 A is 11.6% of the 400 A rating, and the back-EMF is 27.24 V. The battery gives 2,334 W, 1,073 W is lost in Ra and 1,262 W reaches the shaft: 54.0%. With Ra = 0.5 Ω almost half of the battery power is lost in the armature at this point. The question gives no gear ratio or wheel radius, so the speed can only be the motor's.

When does the car start moving, and what is its top speed?

At standstill the motor makes K-phi × Va/Ra and the road needs a = 24.7 N m. The car moves only above

At d1 = 1 (the full 72 V) the speed tops out at 59.33 rad/s, 567 rpm. For a target speed, the duty is closed form: 50 rad/s needs d1 = 0.858.

How does a two-quadrant chopper drive an EV?

Two switches, each with a diode across it, sit between the battery and the motor. NPTEL's electric drives course (IIT Kanpur) describes the circuit: the armature sees the battery voltage when the upper switch Q1 or the upper diode D2 conducts, and zero when the lower diode D1 or the lower switch Q2 conducts. The voltage is never negative, but the current can flow either way, so it works in two quadrants: forward motoring and forward regenerative braking. It is also called a class C chopper.

72 V+Q1Q2D2D1RaLaEmotorVa

Accelerate: Q1 chops at d1 and D1 freewheels. Brake: Q2 chops at d2 and D2 returns the current to the battery.

Accelerating. Q1 is on for d1 of each period, so Va = d1 V on average, and D1 carries the current while Q1 is off. If d1 V is above the back-EMF, the average current flows into the motor.

Braking. Q2 is on for d2 of each period and shorts the armature, so the back-EMF builds up the current in La. When Q2 turns off, that current has to go somewhere: through D2 into the battery. The armature sees zero for d2 of the period and V for the rest.

This page takes d2 as the on-time fraction of the braking switch, as in NPTEL lecture 14, so Va = (1 − d2)V. The same lecture then renames the off-time fraction (T − tON)/T as δ and writes Va = δV, so a text may write d2 V for the same circuit: check which fraction your d2 is. The challenge comes from Iqbal Husain's Electric and Hybrid Vehicles: Design Fundamentals (Problem 7.5 uses the same d1/d2 wording with a different motor), but the book's own braking equations couldn't be read for this page.

For anything this page doesn't model, such as start-up current spikes, a PID speed loop or a four-quadrant H-bridge, use the DC motor speed control calculator.

How much can the motor brake at its cruising speed?

Not much. At 38.91 rad/s the back-EMF is 27.24 V. Braking starts only when (1 − d2) × 72 drops below it, at d2 = 0.6217. With d2 = 0.8, Va = 14.4 V and the braking current is 25.7 A: 18.0 N m of braking torque, 370 W back to the battery and 330 W lost in Ra.

The most current this motor can give at 38.91 rad/s is with the armature shorted (d2 = 1): E/Ra = 54.5 A, 13.6% of rated, and then nothing reaches the battery. Rated 400 A of braking needs 285.7 rad/s (2,728 rpm), well above this car's top speed of 59.3 rad/s. So in this drivetrain regenerative braking alone can't stop the car quickly: friction brakes do most of a hard stop, and the braking torque falls with speed.

The power returned has a peak too:

At the cruising speed that is 371 W at d2 = 0.811. Above it, more d2 means more braking torque and more heat in Ra, but less energy back. For the energy a drive cycle can return, use the regenerative braking energy calculator.

0204017.98 N mbraking torque (N m)rated 280 N m is off the scale-2500250370 Wpower to the battery (W)0.60.70.80.91braking duty ratio d2

What is the armature current ripple at 400 Hz?

It depends on the armature inductance La, which the challenge doesn't give. The armature sees V for d of each period and 0 for the rest, in motoring (d = d1) and in braking (d = 1 − d2). With the back-EMF steady over a period, the current swings between

as derived for a chopper with an RLE load in CSJMU's power electronics notes (ECE-S 501). When the period is short against τ, the current is close to a triangle and

which peaks at d = 0.5 (from d(1 − d); the worst case is derived here). With La = 2 mH, an example value from a different motor in Husain's Problem 7.5, the Week-6 point at d1 = 0.7 and 400 Hz swings 36.5 to 55.3 A: 18.77 A peak to peak, against 18.90 A from the first-order formula and 22.5 A at worst. Keeping it under 10 A needs La ≥ 3.77 mH (3.78 mH first order). At d2 = 0.8 in braking the swing is 14.33 A.

A class C chopper has no discontinuous mode: if the current falls to zero, the lower switch or upper diode lets it reverse. The calculator flags when the current reverses within a period, which is where a one-quadrant chopper would go discontinuous.

4050armature current (A)18.8 A peak to peak050armature voltage (V)012345time (ms)

Check of the formulas against a printed example: CSJMU's Example 3 (100 V, 10 Ω, 50 mH, 1 kHz, d = 0.5) gives Imax 5.25 A, Imin 4.75 A, ΔI 0.5 A with a linear current. The exact form here gives 5.2498 and 4.7502 A, ΔI 0.4996 A.

What did 868 student reports answer?

Skill-Lync read all 868 public "Week-6 Challenge: EV Drivetrain" reports on 22 Nov 2026. 820 contain the speed question. The table sorts them by the speed their text gives, taking the right value first when a report gives several. Answers inside images aren't counted.

Speed in the textReportsExamples
38.91 to 38.92 rad/s: right3821, 2, 3
38.9 rad/s: right to 3 significant figures45—
38.85 rad/s: solves neither quadratic961, 2, 3
38.95 rad/s: close, not the root601, 2, 3
38.2 to 38.35 rad/s: a coefficient slip111, 2, 3
39.7 rad/s: 46.94 in the quadratic21
59.3 rad/s: the full 72 V on the armature21, 2, 3
another value between 30 and 70 rad/s88—
no rad/s value in the text (in an image, or no unit)1341, 2, 3
Total with the question820
  • 46.94. 67 reports put 46.94 in the quadratic (70.56 − 24.7 is 45.86). 62 of them still print 38.85 rad/s, which is the root of neither equation: 46.94 gives 39.70, 45.86 gives 38.915. Only 1 carries 46.94 through to 39.7. A number that matches no working was most likely copied from another report.
  • Units. 118 label the speed in rps. It is rad/s (6.19 rev/s). 6 multiply rad/s by 60 and write about 2,335 "rpm" (1, 2, 3); the right figure, 371.6 rpm, appears in 120.
  • The second root. 440 show the negative root, about −231 rad/s, and reject it.
  • Braking and ripple. Only 2 do anything with d2 (1, 2). 122 mention ripple in their text, none computes the armature current ripple at 400 Hz.
  • km/h. 4 convert to km/h with a wheel radius the question doesn't give.

Counts as of 22 Nov 2026, n = 868, from the text of each public report (Skill-Lync's own data, a starting point, not a grade).

  • 38.85 rad/s solves neither quadratic that appears in the reports: put it into 0.0051 ω² + 0.98 ω − 45.86 and the left side is −0.0895 N m, not 0; into the 46.94 version, −1.17 N m. The roots are 38.915 and 39.697 rad/s. A number that fits no working is most likely copied from another report. Reports with this: 1, 2, 3.

Induction or DC brushless: what does Wally Rippel's post say?

The challenge's last question asks for a summary of Wally Rippel's Tesla blog post "Induction Versus DC Brushless Motors" (9 January 2007). In short: a brushless drive makes less rotor heat and can run at unity power factor, while "the best power factor for the induction drive is about 85 percent", so its peak efficiency is "a few percentage points higher". An induction motor's field can be weakened at light load (B is proportional to V/f), so its average efficiency may be better in a high-performance car. Magnets cost "something like $50 per kilogram"; the catch is that "induction machines are more difficult to control".

What this calculator does not cover

  • Discontinuous and uncontrollable modes. The model is the average, continuous-current one. A class C chopper stays continuous, but with an extra series filter or a different converter it may not.
  • Losses in the chopper. Switches and diodes are ideal, so the battery power equals Va × Ia.
  • Vehicle dynamics. No mass is given, so there is no acceleration time or stopping distance; the road load is the torque at the motor shaft as the challenge gives it.
  • Husain's printed answer. The book's worked numbers for this example couldn't be read for this page, so they aren't reproduced.
Learn EV drivetrains

Finding where a motor and a road load meet, and what the converter can and can't do at that point, is everyday work in EV powertrain teams. The EV drivetrain challenge is part of Skill-Lync's hybrid and electric vehicle courses.

Frequently asked questions

What is the EV's steady-state speed at a 70% duty cycle?

38.915 rad/s (371.6 rpm) of the motor shaft. The chopper gives 0.7 × 72 = 50.4 V, so the motor line is T = 70.56 − 0.98ω. Setting it equal to 24.7 + 0.0051ω² gives 0.0051ω² + 0.98ω − 45.86 = 0. The positive root is the speed; torque 32.42 N m, current 46.3 A.

Why is the negative root rejected?

The quadratic has two roots, 38.91 and -231.07 rad/s. A negative speed means the motor turning backwards, but the load curve 24.7 + 0.0051ω² is the road load for forward motion and the chopper is in its forward-motoring quadrant. Only the positive root is a real operating point here.

Is 38.9 the speed in rps or rad/s?

Rad/s. K-phi is 0.7 V s per radian, so ω from the motor equation is in radians per second. In revolutions per second it is 6.19 rev/s, and in rpm 371.6. Multiplying 38.9 by 60 gives 2,335, which is not rpm: rpm is rad/s × 60/(2π).

What is the duty ratio d2 in a two-quadrant chopper?

The on-time fraction of the braking switch. While it conducts the armature is shorted and current builds up; when it turns off, the current flows back to the battery through the upper diode. The average armature voltage is (1 − d2)V, and the motor brakes when that is below its back-EMF.

Which power converters are used in electric and hybrid vehicles?

An inverter turns battery DC into AC for the traction motor and returns braking energy. DC-DC converters step battery voltage up or down, including one for the 12 V accessories. An onboard charger turns AC from the charge port into DC for the battery. A DC motor uses a chopper, such as this two-quadrant one.

Why can't this EV brake at rated current?

With the armature shorted (d2 = 1) the braking current is the back-EMF over Ra. Rated 400 A needs E = 400 × 0.5 = 200 V, about 286 rad/s. The motor's top speed at d1 = 1 on this road is 59.3 rad/s, where the most braking current is only 83.1 A, so friction brakes must do the rest.

Related on Skill-Lync

Sources

  • NPTEL 108104140, Fundamentals of Electric Drives, Prof. Shyama Prasad Das, IIT Kanpur: Lecture 14 (chopper-fed DC motor for motoring and regenerative braking: Va = δV; in braking the armature is shorted while the switch is on and sees V while it is off, Va = V(T − tON)/T, E − Ia Ra = V) and Lecture 15 (type A two-quadrant chopper, T1/D1/T2/D2, average current (δV − E)/Ra).
  • C.S.J.M. University Kanpur, Power Electronics (ECE-S 501): DC-DC converters (choppers), study material and problems: Imax and Imin of a chopper with an RLE load; Examples 2 and 3 (linear ripple ΔI = toff Vav/L).
  • Malla Reddy College of Engineering and Technology, Electrical and Hybrid Vehicles digital notes: the class C two-quadrant chopper (no discontinuous conduction, Va = δV) and the power electronics of EVs and HEVs.
  • Iqbal Husain, Electric and Hybrid Vehicles: Design Fundamentals, CRC Press, 2003, publisher's preview: Chapter 7 contents (7.3 DC drives, two-quadrant chopper, braking operation, regenerative power; 7.4 operating point analysis) and Problem 7.5 (d1/d2 wording; Ra 0.1 Ω, La 2 mH, K 0.6 V s, 200 A, 500 Hz). The chapter text itself was not available.
  • Wally Rippel, "Induction Versus DC Brushless Motors", Tesla blog, 9 January 2007 (read in the Internet Archive copy).
  • Skill-Lync, all 868 public Week-6 EV Drivetrain reports, read 22 Nov 2026. scripts/verify/two_quadrant_chopper.py solves the same problems another way (numpy.roots and brentq for the operating point and duties, the switched circuit integrated with solve_ivp and shot to its periodic state for the ripple), 98 cases; the page checks itself against it at build time (712 checks).
Free counselling

From a chopper problem to an EV powertrain job.

Getting the operating point right, and saying what the drive can't do, is the kind of answer EV teams look for. A Skill-Lync counsellor can map the HEV or EV course that fits the role you want.

Talk to an EV course counsellor

Free. We call you back, usually the same day.

By submitting you agree to our Terms and Privacy Policy.

Talk to a career counsellor

Talk to a career counsellor

Free 20-minute call. We'll map the right course to where you want to work.

By submitting you agree to our Terms and Privacy Policy.